Inicio Administración de potencia Interruptores y controladores de protección de potencia Controladores de diodo ideal y ORing
Inicio
Administración de potencia
Interruptores y controladores de protección de potencia
Controladores de diodo ideal y ORing

LM7310

ACTIVO

Interruptor de carga de 2.7 V a 23 V, 28 mΩ y 5.5 A con diodo ideal integrado y protección contra so

Haga su pedido ahora
Hoja de datos

LM7310

ACTIVO
Hoja de datos Haga su pedido ahora

Detalles del producto

Vin (max) (V) 23 Vin (min) (V) 2.7 FET Integrated back-to-back FET Device type Ideal diode controller Number of channels 1 Rating Catalog Features Analog current monitor, Overvoltage protection, Power good signal, Reverse current blocking, Reverse polarity protection, Short circuit protection, Thermal shutdown Imax (A) 5.5 Iq (typ) (mA) 0.4 Iq (max) (mA) 0.6 Operating temperature range (°C) -40 to 125 IReverse (typ) (µA) 4.8 Design support Calculation Tool, EVM, Simulation Model Shutdown current (ISD) (mA) (A) 0.0046 Product type Ideal diode controller
Vin (max) (V) 23 Vin (min) (V) 2.7 FET Integrated back-to-back FET Device type Ideal diode controller Number of channels 1 Rating Catalog Features Analog current monitor, Overvoltage protection, Power good signal, Reverse current blocking, Reverse polarity protection, Short circuit protection, Thermal shutdown Imax (A) 5.5 Iq (typ) (mA) 0.4 Iq (max) (mA) 0.6 Operating temperature range (°C) -40 to 125 IReverse (typ) (µA) 4.8 Design support Calculation Tool, EVM, Simulation Model Shutdown current (ISD) (mA) (A) 0.0046 Product type Ideal diode controller
VQFN-HR (RPW) 10 4 mm² (2 mm × 2 mm)
  • Wide operating input voltage range: 2.7 V to 23 V
    • 28-V absolute maximum
    • Withstands negative voltages up to -15 V
  • Integrated back-to-back FETs with low On-Resistance: RON = 28.4 mΩ (typ)
  • Ideal diode operation with true reverse current blocking
  • Fast overvoltage protection

    • 1.2-µs (typ) response time

    • Adjustable overvoltage lockout (OVLO)
  • Fast-trip response to transient overcurrents during steady state
    • 500-ns (typ) response time
    • Latch-off after fault
  • Analog load current monitor output (IMON)
    • Current range: 0.5 A to 5.5 A
    • Accuracy: ±15% (max) (IOUT ≥ 1 A)
  • Active high enable input with adjustable undervoltage lockout threshold (UVLO)
  • Adjustable output slew rate control (dVdt)
  • Overtemperature protection
  • Power Good indication (PG) with adjustable threshold (PGTH)
  • Small footprint: QFN 2 mm x 2 mm, 0.45-mm pitch
  • Wide operating input voltage range: 2.7 V to 23 V
    • 28-V absolute maximum
    • Withstands negative voltages up to -15 V
  • Integrated back-to-back FETs with low On-Resistance: RON = 28.4 mΩ (typ)
  • Ideal diode operation with true reverse current blocking
  • Fast overvoltage protection

    • 1.2-µs (typ) response time

    • Adjustable overvoltage lockout (OVLO)
  • Fast-trip response to transient overcurrents during steady state
    • 500-ns (typ) response time
    • Latch-off after fault
  • Analog load current monitor output (IMON)
    • Current range: 0.5 A to 5.5 A
    • Accuracy: ±15% (max) (IOUT ≥ 1 A)
  • Active high enable input with adjustable undervoltage lockout threshold (UVLO)
  • Adjustable output slew rate control (dVdt)
  • Overtemperature protection
  • Power Good indication (PG) with adjustable threshold (PGTH)
  • Small footprint: QFN 2 mm x 2 mm, 0.45-mm pitch

The LM73100 is a highly integrated circuit protection and power management solution in a small package. The device provides multiple protection modes using very few external components and is a robust defense against voltage surges, reverse polarity, reverse current and excessive inrush current.

With integrated back-to-back FETs, reverse current flow from output to input is blocked at all times, making the device well suited for power MUX/ORing applications. The device uses linear ORing based scheme to ensure almost zero DC reverse current and emulates ideal diode behavior with minimum forward voltage drop and power dissipation.

Applications with particular inrush current requirements can set the output slew rate with a single external capacitor. Loads are protected from input overvoltage conditions by cutting off the output if input exceeds an adjustable overvoltage threshold. The device also provides fast trip response to transient overcurrent events during steady state.

The device provides an accurate sense of the output load current on the analog current monitor pin.

The device is available in a 2-mm x 2-mm, 10-pin HotRod QFN package for improved thermal performance and reduced system footprint.

The device is characterized for operation over a junction temperature range of –40°C to +125°C.

The LM73100 is a highly integrated circuit protection and power management solution in a small package. The device provides multiple protection modes using very few external components and is a robust defense against voltage surges, reverse polarity, reverse current and excessive inrush current.

With integrated back-to-back FETs, reverse current flow from output to input is blocked at all times, making the device well suited for power MUX/ORing applications. The device uses linear ORing based scheme to ensure almost zero DC reverse current and emulates ideal diode behavior with minimum forward voltage drop and power dissipation.

Applications with particular inrush current requirements can set the output slew rate with a single external capacitor. Loads are protected from input overvoltage conditions by cutting off the output if input exceeds an adjustable overvoltage threshold. The device also provides fast trip response to transient overcurrent events during steady state.

The device provides an accurate sense of the output load current on the analog current monitor pin.

The device is available in a 2-mm x 2-mm, 10-pin HotRod QFN package for improved thermal performance and reduced system footprint.

The device is characterized for operation over a junction temperature range of –40°C to +125°C.

filter Buscar otro/a Controladores de diodo ideal y ORing
Descargar Ver vídeo con transcripción Video

Productos similares que pueden interesarle

open-in-new Comparar alternativas
Pin por pin con la misma funcionalidad que el dispositivo comparado
TPS25947 ACTIVO eFuse de 5.5 A, 2.7 V a 23 V, 28 mΩ, con protección de polaridad inversa integrada Adjustable overcurrent protection

Documentación técnica

No se encontraron resultados. Borre su búsqueda y vuelva a intentarlo.
Ver todo 3
Documentación principal Tipo Título Opciones de formato Descargar la versión más reciente en inglés Fecha
* Hoja de datos LM73100, 2.7 - 23 V, 5.5 A Integrated Ideal Diode with Input Reverse Polarity and Overvoltage Protection datasheet (Rev. A) PDF | HTML 15/12/2020
Nota sobre la aplicación Basics of Power MUX (Rev. A) PDF | HTML 20/10/2020
Application brief Fast Role Swap, Linear ORing with TPS25947 and LM73100 in USB-Type C Systems (Rev. A) PDF | HTML 7/10/2020

Diseño y desarrollo

Para conocer los términos adicionales o los recursos necesarios, haga clic en cualquier título de abajo para ver la página de detalles cuando esté disponible.

Placa de evaluación

LM73100EVM — Módulo de evaluación LM73100 de diodo ideal integrado

El módulo de evaluación de diodo ideal integrado LM73100 permite la evaluación del circuito de referencia del diodo ideal LM73100. El dispositivo LM73100 es un interruptor de potencia de diodo ideal de 2.7 V a 23 V y 5.5 A con FET de 28 mΩ integrado, bloqueo de corriente inversa siempre en ON, (...)
Guía del usuario: PDF | HTML
Productos y hardware compatibles
En inventario
Límite:
??asset.out-of-stock-ti_es_MX??
No disponible
Modelo de simulación

LM7310 PSpice Unencrypted Transient Model (Rev. A)

SNOM703A.ZIP (116 KB) - Modelo PSpice
Productos y hardware compatibles
Herramienta de cálculo

SNOR027 — LM73100 Design Calculator

Productos y hardware compatibles
Encapsulado Pines Símbolos CAD, huellas y modelos 3D
VQFN-HR (RPW) 10 Ultra Librarian
Se aplican los Términos y condiciones estándar de TI para los elementos de evaluación.

Pedidos y calidad

Los productos recomendados pueden tener parámetros, módulos de evaluación o diseños de referencia relacionados con este producto de TI.

Soporte y capacitación

Foros de TI E2E™ con asistencia técnica de los ingenieros de TI

Ver todos los temas del foro en inglés

El contenido lo proporcionan “tal como está” TI y los colaboradores de la comunidad y no constituye especificaciones de TI. Consulte los términos de uso.

Si tiene alguna pregunta sobre calidad, encapsulados o pedido de productos de TI, consulte el servicio de asistencia de TI. ​​​​​​​​​​​​​​

Videos