이 제품의 최신 버전이 있습니다
다른 핀 출력을 지원하지만 비교 대상 장치와 동일한 기능.
BQ27441-G1
- Single Series Cell Li-Ion Battery Fuel Gauge
- Resides on System Board
- Supports Embedded or Removable Batteries
- Powered Directly from Battery with Integrated LDO
- Supports a Low-Value External Sense Resistor
(10 mΩ)
- Battery Fuel Gauging Based on Patented Impedance
Track™ Technology- Reports Remaining Capacity and State-of-Charge
(SOC) with Smoothing Filter - Automatically Adjusts for Battery Aging, =
Self-discharge, Temperature, and Rate Changes - Battery State-of-Health (Aging) Estimation
- Reports Remaining Capacity and State-of-Charge
- Microcontroller Peripheral Supports:
- 400-kHz I2C Serial Interface
- Configurable SOC Interrupt or Battery
Low Digital Output Warning - Internal Temperature Sensor or
Host-Reported Temperature
The Texas Instruments bq27441-G1 fuel gauge is a microcontroller peripheral that provides system-side fuel gauging for single-cell Li-Ion batteries. The device requires minimal user configuration and system microcontroller firmware development.
The bq27441-G1 battery fuel gauge uses the patented Impedance Track™ algorithm for fuel gauging, and provides information such as remaining battery capacity (mAh), state-of-charge (%), and battery voltage (mV).
Battery fuel gauging with the bq27441-G1 fuel gauge requires connections only to PACK+ (P+) and PACK– (P–) for a removable battery pack or embedded battery circuit. The tiny, 12-pin, 2.50 mm × 4.00 mm, small outline no-lead (SON) package is ideal for space-constrained applications.
기술 자료
| 상위 문서 | 유형 | 직함 | 형식 옵션 | 최신 영어 버전 다운로드 | 날짜 |
|---|---|---|---|---|---|
| * | 데이터 시트 | bq27441-G1 System-Side Impedance Track Fuel Gauge datasheet (Rev. C) | PDF | HTML | 2014. 12. 19 | |
| 애플리케이션 노트 | Achieving The Successful Learning Cycle | PDF | HTML | 2018. 6. 19 | ||
| 애플리케이션 노트 | Simple Guide to Chemical ID Selection Tool (GPC) (Rev. A) | PDF | HTML | 2018. 6. 5 | ||
| 애플리케이션 노트 | Gauge Communication | 2017. 1. 12 | |||
| 애플리케이션 노트 | Enhanced Resolution Gauging for Low Current Applications Using Scaling | 2016. 10. 26 | |||
| 애플리케이션 노트 | Theory and Implementation of Impedance Track Battery Fuel-Gauging Algorithm (Rev. A) | PDF | HTML | 2014. 5. 16 | ||
| 사용 설명서 | bq27441-G1 Technical Reference Manual (Rev. A) | 2014. 5. 6 | |||
| 사용 설명서 | Quick Start Guide for bq27441-G1 | 2013. 8. 13 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
BOOSTXL-BATPAKMKII — 연료 탱크 MKII 배터리 부스터팩 플러그인 모듈
연료 탱크 MKII BoosterPack™ 플러그인 모듈은 기존 연료 탱크 BoosterPack 모듈의 차세대 설계입니다. 차세대 TI 배터리 모니터링 IC 및 기타 더욱 편리한 사용을 도와주는 새로운 기능이 포함되어 있습니다. 포함된 충전식 리튬 폴리머 배터리로 TI LaunchPad™ 개발 키트에 전원을 공급하여 모바일 애플리케이션 개발 및 평가를 수행할 수 있습니다.
연료 탱크 MKII BoosterPack 플러그인 모듈에는 온도, 충전 상태, 용량 등을 포함한 배터리의 중요한 매개 변수를 제공하는 온보드 리튬 폴리머 배터리 (...)
BQ27441EVM-G1A — 시스템 측 Impedance Track™ 배터리 연료(가스) 게이지 평가 모듈
BQ27441EVM-G1B — 시스템 측 Impedance Track™ 배터리 연료(가스) 게이지 평가 모듈
BQSTUDIO — bqStudio(Battery Management Studio) 소프트웨어
bqStudio(Battery Management Studio)는 TI 배터리 관리 제품의 평가, 설계, 구성, 테스트 또는 기타 활용 프로세스를 지원하는 견고한 종합 툴을 제공합니다. 여기에는 실시간 감시, 그래프 및 로깅 지원, 명령 전송을 위한 간편한 인터페이스, 직접 저수준 통신 및 I/O, 구성, 보정, 학습 주기 수행, 장치를 생산 단계로 가져가기 위한 유용한 파일 생성 등 레지스터 및 데이터 메모리에 대한 전체 액세스를 제공하는 기능은 물론, 자동화된 가이드 지원도 포함됩니다.
bq20xxx 및 bq30xxx와 같은 (...)
BOOSTXL-BATPAKMKII-SW
BQ27XXXSW-LINUX — BQ27XXX용 Linux 드라이버
The Linux driver supports the BQ27x series of Battery Fuel Gauges. The Linux driver supports communication through the I2C/HDQ bus and interfaces with the power supply sub-system to monitor battery properties.
Linux Mainline Status
Available in Linux Main line: Yes
Available through git.ti.com: N/A
(...)
BQEVSW-MKST-UPDATE — Software Update to enable BQEVSW to use MKST-3P-ALT-EV2300
BQ-BATTERY-PROGRAMMER-SW 소프트웨어 개발 키트(SDK)는 TI 배터리 관리 제품을 사용하는 팩의 프로그래밍, 테스트 또는 조립 프로세스를 지원하는 강력한 소프트웨어 명령줄 툴 모음입니다. 이 소프트웨어의 실행 파일은 EV2300 통신 트랜스시버용 MKST-3P-ALT-EV2300 MKS 기술 대안과 함께 작동합니다. 실행 파일은 단일 스테이션에서 작동하지만 MKS Technology Inc.의 추가 소프트웨어 및 GUI를 사용하여 여러 스테이션으로 확장할 수 있습니다. 이 소프트웨어에는 여러 스테이션에 대한 (...)
TIDA-00251 — 시스템 측 Impedance Track 배터리 가스 게이지
The TIDA-00251 reference design is an easy to configure microcontroller peripheral that provides system-side fuel gauging for single-cell Li-Ion batteries. The device requires minimal user configuration and system microcontroller firmware development. The design uses temperature, voltage, and (...)
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| VSON (DRZ) | 12 | Ultra Librarian |
주문 및 품질
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.