DRV8462
- Stepper motor driver
- SPI or H/W interface with STEP/DIR pins
- Up to 1/256 microstepping indexer
-
4.5 V to 65 V operating supply voltage range
- Supports standard 24 V, 36 V and 48 V rails
-
Low R DS(ON): 100 mΩ HS + LS at 24 V, 25°C
- High current capacity per bridge:
- DDW Package: 5 A full-scale, 3.5 A RMS
- DDV Package: 10 A full-scale, 7 A RMS
- DDW package pin-to-pin compatible with -
- DRV8452DDWR: 55 V, 5A full-scale
- DRV8461DDWR: 65 V, 3A full-scale
- Integrated current sensing and regulation
- 5% full-scale current accuracy
- Smart tune and mixed decay regulation options
- Silent step decay mode for silent operation at standstill and low speed
- Automatic Microstepping mode for step frequency interpolation
- Customizable microstepping indexer table
- Auto-torque for load dependent current control
- Standstill Power Saving mode
- Supports 1.8-V, 3.3-V, 5.0-V logic inputs
- Low-current sleep mode (3 µA)
- Separate logic supply voltage ( VCC)
- Protection and diagnostic features
- Sensorless Stall Detection
- VM undervoltage lockout (UVLO)
- Open-load detection (OL)
- Overcurrent protection (OCP)
- Thermal shutdown (OTSD)
- Fault condition output (nFAULT)
- Indexer zero position output ( nHOME)
The DRV8462 is a wide-voltage, high-power, high-performance stepper motor driver. The device supports up to 65-V supply voltage, and integrated MOSFETs with 100 mΩ HS + LS on-resistance allow up to 10-A current.
The auto-torque feature boosts efficiency by adjusting the coil current according to load torque. Standstill power saving mode reduces power loss during motor holding condition. Silent step decay mode provides noiseless operation at low speeds and standstill. The internal current sense eliminates the need for sense resistors, saving PCB area and system cost. Built-in indexer supports up to 1/256 microstepping, and the automatic microstepping mode interpolates the input STEP signal to reduce overhead on the controller. Sensorless stall detection eliminates end stops from the system. The device supports other protection and diagnostic features for robust and reliable operation.
The DRV8462 requires minimal tuning to configure the advanced features. The device supports higher power density compared to external FET drivers, with a smaller PCB area. High energy efficiency with precise, noiseless operation makes the DRV8462 a choice for high-performance stepper systems.
관심 가지실만한 유사 제품
비교 대상 장치보다 업그레이드된 기능을 지원하는 즉각적 대체품.
비교 대상 장치와 유사한 기능.
기술 자료
| 상위 문서 | 유형 | 직함 | 형식 옵션 | 최신 영어 버전 다운로드 | 날짜 |
|---|---|---|---|---|---|
| * | 데이터 시트 | DRV8462: 65 V, 5-10 A Stepper Motor Driver for High Efficiency and Noiseless Operation datasheet (Rev. B) | PDF | HTML | 2023. 9. 28 | |
| 애플리케이션 노트 | System Efficiency Improvement With the DRV8452 and DRV8462 | PDF | HTML | 2023. 1. 19 | ||
| 사용 설명서 | DRV84xx_DRV82x2_DRV89x2-EVM User's Guide (Rev. B) | PDF | HTML | 2023. 1. 18 | ||
| 인증서 | DRV8462EVM EU RoHS Declaration of Conformity (DoC) (Rev. A) | 2023. 1. 17 | |||
| 애플리케이션 노트 | Integrated FETs vs External FETs: Performance Comparison of Motor Drivers | PDF | HTML | 2022. 12. 22 | ||
| 인증서 | DRV8462VEVM EU RoHS Declaration of Conformity (DoC) | 2022. 12. 16 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
DRV8462EVM — 자동 마이크로스테핑 기능이 있는 스테퍼 모터 드라이버용 DRV8462 평가 모듈
DRV8462EVM 평가 모듈은 DRV8462DDWR의 기능과 성능을 입증합니다.
DRV8462은 산업용 애플리케이션을 위한 완전 통합 스테퍼 모터 드라이버입니다. 이 장치는 4.5V~65V 공급 범위에서 작동하며, 최대 5A의 풀 스케일 전류를 구동할 수 있습니다.
DRV84XX-DRV89X2-DRV82X2-EVM-SOFTWARE — EVM GUI and device firmware for DRV84XX_DRV89X2_DRV82X2 family
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| HTSSOP (DDV) | 44 | Ultra Librarian |
| HTSSOP (DDW) | 44 | Ultra Librarian |
주문 및 품질
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.