TPS61052
- Four Operational Modes
- Torch and Flash up to ILED = 1200 mA
- Voltage-Regulated Boost Converter: 4.5 V,
5 V, and 5.25 V - Shutdown: 0.3 µlA (Typical)
- Total Solution Circuit Area < 25 mm2
- Up to 96% Efficiency
- I2C-Compatible Interface up to 400 kbps
- Integrated LED Turnon Safety Timer
- Zero Latency TX-Masking Input (TPS61050)
- Hardware Voltage Mode Selection Input
(TPS61052) - Integrated ADC for LED VF Monitoring
- Integrated Low Light Dimming Mode
- LED Disconnect During Shutdown
- Open and Shorted LED Protection
- Overtemperature Protection
- Available in a 12-Pin NanoFree™ (CSP) and
10-Pin QFN Packaging
The TPS6105x device is based on a high-frequency synchronous-boost topology with constant current sink to drive single white LEDs. The device uses an inductive fixed-frequency PWM control scheme using small external components, minimizing input ripple current.
The 2-MHz switching frequency allows the use of small and low profile 2.2-µH inductors. To optimize overall efficiency, the device operates with only a 250-mV LED feedback voltage.
The TPS6105x device not only operates as a regulated current source, but also as a standard voltage-boost regulator. This additional operating mode can be useful to supply other high-power devices in the system, such as a hands-free audio power amplifier, or any other component requiring a supply voltage higher than the battery voltage (refer to TPS61052).
For highest flexibility, the LED current or the desired output voltage can be programmed through an I2C compatible interface. To simplify flash synchronization with the camera module, the device offers a trigger pin (FLASH_SYNC) for fast LED turnon time.
When the TPS6105x is not in use, it can be put into shutdown mode through the I2C-compatible interface, reducing the input current to 0.3 µA (typical). During shutdown, the LED pin is high impedance to avoid leakage current through the LED.
기술 자료
| 상위 문서 | 유형 | 직함 | 형식 옵션 | 최신 영어 버전 다운로드 | 날짜 |
|---|---|---|---|---|---|
| * | 데이터 시트 | TPS6105x 1.2-A High-Power White LED Driver 2-MHz Synchronous Boost Converter With I2C Compatible Interface datasheet (Rev. A) | PDF | HTML | 2015. 9. 30 | |
| 백서 | Common LED Functions and LED Driver Design Considerations | 2020. 9. 21 | |||
| 애플리케이션 노트 | Performing Accurate PFM Mode Efficiency Measurements (Rev. A) | 2018. 12. 11 | |||
| 선택 가이드 | Power Management Guide 2018 (Rev. R) | 2018. 6. 25 | |||
| 애플리케이션 노트 | Optimizing Transient Response of Internally Compensated DC-DC Converters (Rev. B) | 2017. 11. 29 | |||
| 애플리케이션 노트 | Extending the Soft Start Time Without a Soft Start Pin (Rev. B) | 2017. 6. 15 | |||
| 애플리케이션 노트 | Minimizing Ringing at the Switch Node of a Boost Converter | 2006. 9. 15 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
SLUC569 — TPS61050/TPS61052 GUI Software
TPS6105XEVM-SW — TPS6105x 평가 모듈용 소프트웨어
The TPS6105x EVM Software provides a software interface for the TPS6105x EVM boards. Use this software to change the TPS6105x IC registers via the USB Interface Adapter.
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| DSBGA (YZG) | 12 | Ultra Librarian |
| VSON (DRC) | 10 | Ultra Librarian |