TPS65916
- System Voltage Range from 3.135 V to 5.25 V
- Low-Power Consumption
- 20 µA in Off Mode
- 90 µA in Sleep Mode With Two SMPSs Active
-
Five Step-Down Switched-Mode Power Supply (SMPS) Regulators:
- 0.7- to 3.3-V Output Range in 10- or 20-mV Steps
- Two SMPS Regulators With 3.5-A Capability, With the Ability to Combine into 7-A Output in Dual-Phase Configuration, With Differential Remote Sensing (Output and Ground)
- Three Other SMPS Regulators with 3-A, 2-A, and 1.5-A Capabilities
- Dynamic Voltage Scaling (DVS) Control and Output Current Measurement in 3.5-A and 3-A SMPS Regulators
- Hardware and Software Controlled Eco-mode™ Supplying up to 5 mA
- Short-Circuit Protection
- Power-Good Indication (Voltage and Overcurrent Indication)
- Internal Soft-Start for In-Rush Current Limitation
- Ability to Synchronize to External Clock between 1.7 MHz and 2.7 MHz
- Five Low-Dropout (LDO) Linear Regulators:
- 0 .9- to 3.3-V Output Range in 50-mV steps
- Two With 300-mA Capability and Bypass Mode
- One With 100-mA Capability and Capable of Low-Noise Performance up to 50 mA
- Two Other LDOs With 200-mA Current Capability
- Short-Circuit Protection
- 12-Bit Sigma-Delta General-Purpose ADC (GPADC) With 8 Input Channels (2 external)
- Thermal Monitoring With High Temperature Warning and Thermal Shutdown
- Power Sequence Control:
- Configurable Power-Up and Power-Down Sequences (OTP)
- Configurable Sequences Between the SLEEP and ACTIVE State Transition (OTP)
- Three Digital Output Signals that can be Included in the Startup Sequence
- Selectable Control Interface:
- One SPI for Resource Configurations and DVS Control
- Two
I2C Interfaces.
- One Dedicated for DVS Control
- One General Purpose I2C Interface for Resource Configuration and DVS Control
- OTP Bit-Integrity Error Detection With Options to Proceed or Hold Power-Up Sequence and RESET_OUT Release
- Package Option:
- 7-mm × 7-mm 48-pin VQFN With 0.5-mm Pitch
The TPS65916 PMIC integrates five configurable step-down converters with up to 3.5 A of output current to power the processor core, memory, I/O, and preregulation of LDOs The step-down converters are synchronized to an internal 2.2-MHz clock to improve EMC performance of the device. The GPIO_3 pin allows the step-down converters to synchronize to an external clock, allowing multiple devices to synchronize to the same clock which improves system-level EMC performance. The device also contains five LDOs to power low-current or low-noise domains.
The power-sequence controller uses one-time programmable (OTP) memory to control the power sequences, as well as default configurations such as output voltage and GPIO configurations. The OTP is factory-programmed to allow start-up without any software required. Most static settings can be changed from the default through SPI or I2C to configure the device to meet many different system needs. For example, voltage-scaling registers are used to support dynamic voltage-scaling requirements of processors. The OTP also contains a bit-integrity-error detection feature to stop the power-up sequence if an error is detected, preventing the system from starting in an unknown state.
The TPS65916 device also includes an analog-to-digital converter (ADC) to monitor the system state. The GPADC includes two external channels to monitor any external voltage, as well as internal channels to measure supply voltage, output current, and die temperature, allowing the processor to monitor the health of the system. The device offers a watchdog to monitor for software lockup, and includes protection and diagnostic mechanisms such as short-circuit protection, thermal monitoring, shutdown, and automatic ADC conversions to detect if a voltage is below a predefined threshold. The PMIC can notify the processor of these events through the interrupt handler, allowing the processor to take action in response.
관심 가지실만한 유사 제품
비교 대상 장치와 동일한 기능을 지원하는 핀 대 핀.
기술 자료
| 상위 문서 | 유형 | 직함 | 형식 옵션 | 최신 영어 버전 다운로드 | 날짜 |
|---|---|---|---|---|---|
| * | 데이터 시트 | TPS65916 3.1-V to 5.2-V, 5 Buck Converter and 5 LDO Power Management IC (PMIC) datasheet (Rev. C) | PDF | HTML | 2018. 8. 20 | |
| * | 사용 설명서 | TPS65916 Register Map (Rev. A) | 2017. 4. 11 | ||
| 애플리케이션 노트 | POR Generation in TPS65903x, TPS65917-Q1, TPS65919-Q1, and TPS65916 Devices (Rev. A) | 2018. 9. 21 | |||
| 애플리케이션 노트 | TPS65917 Power Estimation Tool (Rev. B) | 2018. 6. 14 | |||
| 사용 설명서 | TPS65916 User's Guide to Power AM570x (Rev. A) | 2018. 5. 7 | |||
| 사용 설명서 | TPS65916 User’s Guide to Power AM571x (Rev. D) | 2018. 5. 7 | |||
| 애플리케이션 노트 | Guide to Using the GPADC in TPS65903x, TPS65917-Q1, TPS65919-Q1, and TPS65916 de (Rev. A) | 2017. 12. 13 | |||
| 기술 문서 | How to implement remote sense in your PMIC | PDF | HTML | 2016. 11. 17 | ||
| 기술 문서 | Using PMICs to support a wide range of power sequencing requirements | PDF | HTML | 2016. 11. 1 | ||
| 애플리케이션 노트 | TPS65916 Design Checklist | 2016. 8. 22 | |||
| 애플리케이션 노트 | Adaptive (Dynamic) Voltage (Frequency) Scaling – Motivation and Implementations | 2014. 3. 28 |
설계 및 개발
전원 공급 솔루션
TPS65916을 포함하는 솔루션을 살펴보세요. TI는 칩(SoC), 프로세서, 마이크로컨트롤러, 센서 또는 FPGA(Field Programmable Gate Array)의 TI와 비TI 시스템을 위한 전원 공급 솔루션을 제공합니다.
TPS65916EVM — TPS65916 전원 관리 IC 평가 모듈
TPS65916 장치는 차량용 애플리케이션을 위한 PMIC(전원 관리 통합 회로)입니다. 이 장치는 메모리, 프로세서 코어, I/O(입력/출력) 또는 LDO의 사전 조정을 위해 최대 3.5A의 출력 전류를 제공하는 5개의 구성 가능한 스텝다운 컨버터를 탑재하고 있습니다. 또한 TPS65916에는 외부 사용을 위한 LDO 5개가 포함되어 있습니다.
TIDEP-0100 — AM570x 6계층 PCB 레퍼런스 설계
TIPA-050027 — 산업용 애플리케이션을 위한 TPS65916 PMIC를 사용한 AM571 전원 공급 장치 설계
이 전원 공급 장치 설계는 AM57x 프로세서에 전원을 공급하기 위해 최적화된 전력 관리 IC(PMIC)를 설명합니다. 사용 설명서는 TPS65916 PMIC와 AM571x 프로세서 간 연결 가이드로 사용할 수 있습니다. 이 설명서는 OTP 구성과 함께 전원 업, 전원 다운 및 웜 리셋 시퀀스와 플랫폼 연결에 대해 설명합니다.
TIPA-050030 — 산업용 애플리케이션을 위한 TPS65916 PMIC를 사용한 AM570 전원 공급 장치 설계
이 전원 공급 장치 설계는 AM57x 프로세서에 전원을 공급하기 위해 최적화된 전력 관리 IC(PMIC)를 설명합니다. 사용 설명서는 TPS65916 PMIC와 AM570x 프로세서 간 연결 가이드로 사용할 수 있습니다. 이 설명서는 OTP 구성과 함께 전원 업, 전원 다운 및 웜 리셋 시퀀스와 플랫폼 연결에 대해 설명합니다.
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| VQFN (RGZ) | 48 | Ultra Librarian |
주문 및 품질
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.