首頁 微控制器 (MCU) 與處理器 Microcontrollers Low-power MCUs
首頁
微控制器 (MCU) 與處理器
Microcontrollers
Low-power MCUs

MSP430FR4132

現行

具 8KB FRAM、1KB SRAM、10 位元 ADC、LCD、UART/SPI/I2C、IR 邏輯、定時器的 16 MHz MCU

立即訂購
產品規格表
使用指南
勘誤表

MSP430FR4132

現行
產品規格表 立即訂購

產品詳細資料

CPU MSP430 Frequency (MHz) 16 Flash memory (kByte) 8 RAM (kByte) 1 ADC type 10-bit SAR Features IR Modulation Logic, LCD, Real-time clock UART 1 Number of ADC channels 10 SPI 2 USB No Hardware accelerators 0 Operating temperature range (°C) -40 to 85 Rating Catalog Communication interface I2C, SPI, UART Operating system BareMetal (No OS), TI RTOS Nonvolatile memory (kByte) 8 Number of GPIOs 60 Number of I2Cs 1 Security Secure debug
CPU MSP430 Frequency (MHz) 16 Flash memory (kByte) 8 RAM (kByte) 1 ADC type 10-bit SAR Features IR Modulation Logic, LCD, Real-time clock UART 1 Number of ADC channels 10 SPI 2 USB No Hardware accelerators 0 Operating temperature range (°C) -40 to 85 Rating Catalog Communication interface I2C, SPI, UART Operating system BareMetal (No OS), TI RTOS Nonvolatile memory (kByte) 8 Number of GPIOs 60 Number of I2Cs 1 Security Secure debug
LQFP (PM) 64 144 mm² 12 x 12 TSSOP (DGG) 56 113.4 mm² 14 x 8.1 TSSOP (DGG) 48 101.25 mm² 12.5 x 8.1
  • Embedded microcontroller
    • 16-bit RISC architecture up to 16 MHz
    • Wide supply voltage range from 3.6 V down to 1.8 V (minimum supply voltage is restricted by SVS levels, see the Section 8.12.1.1)
  • Optimized low-power modes (at 3 V)
    • Active mode: 126 µA/MHz
    • Standby mode: <1 µA with real-time clock (RTC) counter and liquid crystal display (LCD)
    • Shutdown (LPM4.5): 15 nA
  • High-performance analog
    • 10-channel 10-bit analog-to-digital converter (ADC)
      • Internal 1.5-V reference
      • Sample-and-hold 200 ksps
    • Low-power LCD driver
      • Supports up to 4×36- or 8×32-segment LCD configuration
      • On-chip charge pump to keep LCD active in standby mode (LPM3.5)
      • Each LCD pin software configurable as SEG or COM
      • Contrast control from 2.6 V to 3.5 V by 0.06‑V steps
  • Low-power ferroelectric RAM (FRAM)
    • Up to 15.5KB of nonvolatile memory
    • Built-in error correction code (ECC)
    • Configurable write protection
    • Unified memory of program, constants, and storage
    • 1015 write cycle endurance
    • Radiation resistant and nonmagnetic
  • Intelligent digital peripherals
    • IR modulation logic
    • Two 16-bit timers with three capture/compare registers each (Timer_A3)
    • One 16-bit counter-only RTC counter
    • 16-bit cyclic redundancy checker (CRC)
  • Enhanced serial communications
    • Enhanced USCI A (eUSCI_A) supports UART, IrDA, and SPI
    • Enhanced USCI B (eUSCI_B) supports SPI and I2C
  • Clock system (CS)
    • On-chip 32-kHz RC oscillator (REFO)
    • On-chip 16-MHz digitally controlled oscillator (DCO) with frequency-locked loop (FLL)
      • ±1% accuracy with on-chip reference at room temperature
    • On-chip very low-frequency 10-kHz oscillator (VLO)
    • On-chip high-frequency modulation oscillator clock (MODCLK)
    • External 32-kHz crystal oscillator (XT1)
    • Programmable MCLK prescalar of 1 to 128
    • SMCLK derived from MCLK with programmable prescalar of 1, 2, 4, or 8
  • General input/output and pin functionality
    • 60 I/Os on 64-pin package
    • 16 interrupt pins (P1 and P2) can wake MCU from LPMs
    • All I/Os are capacitive touch I/O
  • Development tools and software
  • Family members (also see Section 6)
    • MSP430FR4133: 15KB of program FRAM + 512B of information FRAM + 2KB of RAM
    • MSP430FR4132: 8KB of program FRAM + 512B of information FRAM + 1KB of RAM
    • MSP430FR4131: 4KB of program FRAM + 512B of information FRAM + 512B of RAM
  • Package options
    • 64 pin: LQFP (PM)
    • 56 pin: TSSOP (G56)
    • 48 pin: TSSOP (G48)
  • Embedded microcontroller
    • 16-bit RISC architecture up to 16 MHz
    • Wide supply voltage range from 3.6 V down to 1.8 V (minimum supply voltage is restricted by SVS levels, see the Section 8.12.1.1)
  • Optimized low-power modes (at 3 V)
    • Active mode: 126 µA/MHz
    • Standby mode: <1 µA with real-time clock (RTC) counter and liquid crystal display (LCD)
    • Shutdown (LPM4.5): 15 nA
  • High-performance analog
    • 10-channel 10-bit analog-to-digital converter (ADC)
      • Internal 1.5-V reference
      • Sample-and-hold 200 ksps
    • Low-power LCD driver
      • Supports up to 4×36- or 8×32-segment LCD configuration
      • On-chip charge pump to keep LCD active in standby mode (LPM3.5)
      • Each LCD pin software configurable as SEG or COM
      • Contrast control from 2.6 V to 3.5 V by 0.06‑V steps
  • Low-power ferroelectric RAM (FRAM)
    • Up to 15.5KB of nonvolatile memory
    • Built-in error correction code (ECC)
    • Configurable write protection
    • Unified memory of program, constants, and storage
    • 1015 write cycle endurance
    • Radiation resistant and nonmagnetic
  • Intelligent digital peripherals
    • IR modulation logic
    • Two 16-bit timers with three capture/compare registers each (Timer_A3)
    • One 16-bit counter-only RTC counter
    • 16-bit cyclic redundancy checker (CRC)
  • Enhanced serial communications
    • Enhanced USCI A (eUSCI_A) supports UART, IrDA, and SPI
    • Enhanced USCI B (eUSCI_B) supports SPI and I2C
  • Clock system (CS)
    • On-chip 32-kHz RC oscillator (REFO)
    • On-chip 16-MHz digitally controlled oscillator (DCO) with frequency-locked loop (FLL)
      • ±1% accuracy with on-chip reference at room temperature
    • On-chip very low-frequency 10-kHz oscillator (VLO)
    • On-chip high-frequency modulation oscillator clock (MODCLK)
    • External 32-kHz crystal oscillator (XT1)
    • Programmable MCLK prescalar of 1 to 128
    • SMCLK derived from MCLK with programmable prescalar of 1, 2, 4, or 8
  • General input/output and pin functionality
    • 60 I/Os on 64-pin package
    • 16 interrupt pins (P1 and P2) can wake MCU from LPMs
    • All I/Os are capacitive touch I/O
  • Development tools and software
  • Family members (also see Section 6)
    • MSP430FR4133: 15KB of program FRAM + 512B of information FRAM + 2KB of RAM
    • MSP430FR4132: 8KB of program FRAM + 512B of information FRAM + 1KB of RAM
    • MSP430FR4131: 4KB of program FRAM + 512B of information FRAM + 512B of RAM
  • Package options
    • 64 pin: LQFP (PM)
    • 56 pin: TSSOP (G56)
    • 48 pin: TSSOP (G48)

MSP430FR41xx ultra-low-power (ULP) microcontroller family supports low-cost LCD applications that benefit from an integrated 10-bit ADC such as remote controls, thermostats, smart meters, blood glucose monitors, and blood pressure monitors. The MCUs feature a powerful 16-bit RISC CPU, 16-bit registers, and constant generators that contribute to maximum code efficiency. The digitally controlled oscillator (DCO) allows the device to wake up from low-power modes to active mode in less than 10 µs. The architecture, combined with extensive low-power modes, is optimized to achieve extended battery life in portable measurement applications.

The MSP430™ FRAM microcontroller platform combines uniquely embedded ferroelectric random access memory (FRAM) and a holistic ultra-low-power system architecture, allowing system designers to increase performance while lowering energy consumption. FRAM technology combines the low-energy fast writes, flexibility, and endurance of RAM with the nonvolatile behavior of flash.

MSP430FR41x MCUs are supported by an extensive hardware and software ecosystem with reference designs and code examples to get your design started quickly. Development kits for the MSP430FR41xx include the MSP-EXP430FR4133 LaunchPad™ development kit and the MSP-TS430PM64D 64-pin target development board. TI also provides free MSP430Ware™ software, which is available as a component of Code Composer Studio™ IDE desktop and cloud versions within TI Resource Explorer. MSP430 MCUs are also supported by extensive online collateral, such as our housekeeping example series, MSP Academy training, and online support through the TI E2E™ support forums.

For complete module descriptions, see the MSP430FR4xx and MSP430FR2xx Family User’s Guide .

MSP430FR41xx ultra-low-power (ULP) microcontroller family supports low-cost LCD applications that benefit from an integrated 10-bit ADC such as remote controls, thermostats, smart meters, blood glucose monitors, and blood pressure monitors. The MCUs feature a powerful 16-bit RISC CPU, 16-bit registers, and constant generators that contribute to maximum code efficiency. The digitally controlled oscillator (DCO) allows the device to wake up from low-power modes to active mode in less than 10 µs. The architecture, combined with extensive low-power modes, is optimized to achieve extended battery life in portable measurement applications.

The MSP430™ FRAM microcontroller platform combines uniquely embedded ferroelectric random access memory (FRAM) and a holistic ultra-low-power system architecture, allowing system designers to increase performance while lowering energy consumption. FRAM technology combines the low-energy fast writes, flexibility, and endurance of RAM with the nonvolatile behavior of flash.

MSP430FR41x MCUs are supported by an extensive hardware and software ecosystem with reference designs and code examples to get your design started quickly. Development kits for the MSP430FR41xx include the MSP-EXP430FR4133 LaunchPad™ development kit and the MSP-TS430PM64D 64-pin target development board. TI also provides free MSP430Ware™ software, which is available as a component of Code Composer Studio™ IDE desktop and cloud versions within TI Resource Explorer. MSP430 MCUs are also supported by extensive online collateral, such as our housekeeping example series, MSP Academy training, and online support through the TI E2E™ support forums.

For complete module descriptions, see the MSP430FR4xx and MSP430FR2xx Family User’s Guide .
filter 尋找其它 Low-power MCUs
下載 觀看有字幕稿的影片 影片

技術文件

star =TI 所選的此產品重要文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 32
重要文件 類型 標題 格式選項 日期
* Data sheet MSP430FR413x Mixed-Signal Microcontrollers datasheet (Rev. F) PDF | HTML 2021年 12月 8日
* Errata MSP430FR4132 Device Erratasheet (Rev. W) PDF | HTML 2021年 5月 27日
* User guide MSP430FR4xx and MSP430FR2xx Family User's Guide (Rev. I) 2019年 3月 13日
Application note Migration Guide From MSP430 MCUs to MSPM0 MCUs (Rev. B) PDF | HTML 2025年 6月 2日
User guide MSP430 FRAM Devices Bootloader (BSL) User's Guide (Rev. AB) PDF | HTML 2022年 9月 22日
Application note How to achieve higher accuracy timer with internal oscillator on MSP430 2021年 12月 10日
Application note UART-to-I2C Bridge Using Low-Memory MSP430™ MCUs (Rev. A) PDF | HTML 2021年 9月 29日
Application note ESD Diode Current Specification (Rev. B) PDF | HTML 2021年 8月 23日
Application note MSP430 FRAM Technology – How To and Best Practices (Rev. B) 2021年 8月 12日
Application note Designing With the MSP430FR4xx and MSP430FR2xx ADC (Rev. A) PDF | HTML 2021年 8月 2日
Application note Low-Power Battery Voltage Measurement With MSP430FR MCU On-Chip VREF and ADC (Rev. B) PDF | HTML 2021年 8月 2日
Application note Migrating from MSP430 F2xx and G2xx families to MSP430 FR4xx and FR2xx family (Rev. G) PDF | HTML 2021年 8月 2日
Application note Migration from MSP430 FR58xx, FR59xx, and FR6xx to FR4xx and FR2xx (Rev. B) PDF | HTML 2021年 8月 2日
Application note MSP430 System-Level ESD Considerations (Rev. B) PDF | HTML 2021年 7月 14日
User guide MSP430 MCUs Development Guide Book (Rev. A) PDF | HTML 2021年 5月 13日
Application note MSP430FR2xx and MSP430FR4xx DCO+FLL Application Guide 2020年 12月 7日
Application note MSP430 Embedded Application Binary Interface (Rev. A) PDF | HTML 2020年 6月 2日
Application note MSP430 System ESD Troubleshooting Guide PDF | HTML 2019年 12月 13日
White paper Capacitive Touch and MSP Microcontrollers (Rev. A) 2017年 4月 27日
EVM User's guide MSP430FR4133 LaunchPad Development Kit (MSP-EXP430FR4133) User's Guide (Rev. B) 2017年 1月 17日
White paper Smart Fault Indicator with MSP430 FRAM Microcontrollers 2016年 9月 26日
Application note General Oversampling of MSP ADCs for Higher Resolution (Rev. A) PDF | HTML 2016年 4月 1日
Application note VLO Calibration on the MSP430FR4xx and MSP430FR2xx Family (Rev. A) 2016年 2月 19日
Application note MSP Code Protection Features PDF | HTML 2015年 12月 7日
Application note Designing With MSP430™ MCUs and Segment LCDs (Rev. A) PDF | HTML 2015年 7月 20日
Application note Infrared Remote Control Implementation With MSP430FR4xx (Rev. B) 2015年 6月 30日
Design guide Thermostat Implementation With MSP430FR4xx Design Guide (Rev. A) 2014年 10月 15日
Design guide Water Meter Implementation With MSP430FR4xx Design Guide (Rev. A) 2014年 10月 15日
Application note Migrating from the MSP430F4xx to Family to the MSP430FR4xx Family 2014年 10月 3日
Application note MSP430 FRAM Quality and Reliability (Rev. A) 2014年 5月 1日
White paper FRAM FAQs 2014年 4月 23日
White paper Benchmarking MCU power consumption for ultra-low-power applications 2012年 10月 26日

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

ALGO-3P-UISP1-TI — 適用於德州儀器裝置的 Algocraft μISP1 編程器

μISP 可以連接到主機 PC (內建 RS-232、USB、LAN 連接) 或獨立模式工作。

在單機模式下，只要按下「開始」按鈕或透過一些 TTL 控制線，就可以執行編程週期。

其緊湊的尺寸和多功能性可輕鬆整合到生產環境、手動和自動化程序中。

從：Algocraft
造訪合作夥伴網站
開發套件

MSP-EXP430FR4133 — MSP430FR4133 LaunchPad™ 開發套件

MSP-EXP430FR4133 LaunchPad 開發套件是易用的評估模組 (EVM)，適用於 MSP430FR4133 微控制器。其包含開始以 MSP430™ 超低功耗 (ULP) FRAM 架構微控制器 (MCU) 平台著手開發所需的一切，包括用於編程、偵錯和能源量測的板載模擬功能。電路板配備板載按鈕和 LED 以快速整合簡單的使用者介面，並配備液晶顯示器 (LCD)，展現了具有軟體可配置之靈活接腳的整合式驅動器。
使用指南: PDF
TI.com 無法提供
開發套件

MSP-TS430PM64D — 適用於 MSP430FR2x/4x MCU 的 64 針腳目標開發基板

Note: This kit does not include MSP430 microcontroller samples.  To sample the compatible devices, please visit the product page or select the related MCU after adding the tool to the TI Store cart.

The MSP-TS430PM64D is a standalone 64-pin ZIF socket target board used to program and debug the (...)

使用指南: PDF | HTML
TI.com 無法提供
硬體程式設計工具

MSP-FET — MSP MCU 程式設計工具和偵錯器

MSP-FET 是一款強大的模擬開發工具，通常稱為偵錯探測器，可讓使用者快速展開 MSP 低功耗微控制器 (MCU) 的開始工作。

它支援透過 JTAG 和 SBW 介面進行編程和即時偵錯。此外，MSP-FET 也能在電腦 USB 介面與 MSP UART 間提供後通道 UART 連接。這為 MSP 程式設計工具提供了一種便利的方法，能在 MSP 和電腦上執行的終端之間進行串行通訊。它也支援透過 UART 和 I2C 通訊協定，使用 BSL（自舉式載入程式）將程式（通常稱為韌體）載入到 MSP 目標。

USB 介面可將 MSP-FET 連接至電腦，而 14 針腳連接器則可存取 MSP (...)

使用指南: PDF | HTML
TI.com 無法提供
硬體程式設計工具

ALGO-3P-WRITENOW — Algocraft WriteNow！程式設計工具

WriteNow! 系統內編程器系列是可編程產業的一大突破。此編程器支援多家製造商的眾多裝置 (例如微控制器、記憶體、CPLD 與其他可編程裝置)。其尺寸精巧，便於整合至 ATE 與固定裝置。編程器可單機運作，或透過內建的 RS-232、LAN 與 USB 連接埠與主機電腦連線，並隨附操作簡易的工具軟體。

從：Algocraft
造訪合作夥伴網站
軟體開發套件 (SDK)

MSP430-SDK — MSPWare for MSP430 Microcontrollers

MSP430-SDK is a collection of resources that help users to write effective code for MSP430 microcontrollers (MCUs). These resources support ALL MSP430 microcontrollers. As one user mentioned, “It’s essentially everything developers need to become MSP430 microcontroller experts!”

This collection of (...)

支援產品和硬體

支援產品和硬體
瀏覽 下載選項
程式碼範例或展示

SLAC625 — MSP430FR413x, MSP430FR203x code examples

支援產品和硬體

支援產品和硬體
下載
驅動程式或資料庫

MSPMATHLIB — 適用於 MSP430 的浮點數學函式庫

MSPMathLib is an accelerated floating point math library for MSP430™ MCUs that delivers up to 26x faster computation for the most commonly used math functions. The library seamlessly integrates with projects to replace floating point math functions such as sin, cos, tan, log, exp and sqrt, (...)
使用指南: PDF
檢視選項
韌體

MSPFRBOOT — MSPFRBOOT

The bootloader (BSL) on MSP430™ microcontrollers (MCUs) lets users communicate with embedded memory in the MSP MCUs during the prototyping phase, final production, and in service. This is done through standard interfaces such as UART, I2C, SPI, and USB. Both the programmable memory (Flash/FRAM) and (...)

支援產品和硬體

支援產品和硬體
下載選項
快速入門

TI-DEVELOPER-ZONE — Start embedded development on your desktop or in the cloud

From evaluation to deployment the TI Developer Zone provides a comprehensive range of software, tools and training to ensure that you have everything you need for each stage of the development process.
支援產品和硬體

支援產品和硬體
開始使用
IDE、配置、編譯器或偵錯程式

CCSTUDIO — Code Composer Studio™ integrated development environment (IDE)

Code Composer Studio is an integrated development environment (IDE) for TI's microcontrollers and processors. It is comprised of a rich suite of tools used to build, debug, analyze and optimize embedded applications. Code Composer Studio is available across Windows®, Linux® and macOS® platforms.

(...)

支援產品和硬體

支援產品和硬體
啟動 下載選項
IDE、配置、編譯器或偵錯程式

ENERGIA — Energia

Energia is an open source & community-driven integrated development environment (IDE) & software framework. Based on the Wiring framework, Energia provides an intuitive coding environment as well as a robust framework of easy-to-use functional APIs & libraries for programming a (...)
View Options
IDE、配置、編譯器或偵錯程式

ENERGYTRACE — EnergyTrace 技術

EnergyTrace™ software for MSP430™ MCUs, MSP432™ MCUs, CC13xx wireless MCUs and CC26xx wireless MCUs is an energy-based code analysis tool that measures and displays the energy profile of an application and helps optimize it for ultra-low-power consumption.

As most developers know, it is difficult to (...)

使用指南: PDF
檢視選項
IDE、配置、編譯器或偵錯程式

IAR-KICKSTART — IAR Embedded Workbench

IAR Embedded Workbench delivers a complete development toolchain for building and debugging embedded applications for your selected target microcontroller. The included IAR C/C++ Compiler generates highly optimized code for your application, and the C-SPY Debugger is a fully integrated debugger for (...)
從：IAR Systems
使用指南: PDF
View Options
線上培訓

MSP430-ACADEMY — MSP430™ academy

MSP430™ academy delivers easy-to-use training modules that span a wide range of topics and LaunchPads in the MSP430 MCU portfolio.
支援產品和硬體

支援產品和硬體
瀏覽
作業系統 (OS)

WHIS-3P-SAFERTOS — WITTENSTEIN SAFERTOS 預先認證的安全 RTOS

SAFERTOS® 是專為嵌入式處理器設計的獨特即時作業系統。經 TÜV SÜD 預先認證，符合 IEC 61508 SIL3 與 ISO 26262 ASILD 標準。SAFERTOS® 是由 WHIS 專家團隊專為安全而打造，適用於全球重要安全應用。WHIS 與德州儀器的合作已經超過十年。在此期間，WHIS 已將 SAFERTOS® 移植至各種 TI 處理器，支援所有熱門核心，並可依要求提供其他架構。SAFERTOS® 專為您的特定處理器/編譯器組合量身打造，隨附完整的原始程式碼與設計保證包，可完全一目了然整個設計生命週期。許多 WHIS 客戶開始使用 FreeRTOS (...)
從：WITTENSTEIN High Integrity Systems
造訪合作夥伴網站
軟體程式設計工具

MSP-GANG-SOFTWARE — MSP-GANG Software

The MSP Gang Programmer (MSP-GANG) is a MSPM0/MSP430/MSP432 device programmer that can program up to eight identical devices at the same time.
支援產品和硬體

支援產品和硬體
下載選項
軟體程式設計工具

UNIFLASH — UniFlash for most TI microcontrollers (MCUs) and mmWave sensors

UniFlash is a software tool for programming on-chip flash on TI microcontrollers and wireless connectivity devices and on-board flash for TI processors. UniFlash provides both graphical and command-line interfaces.

UniFlash can be run from the cloud on the TI Developer Zone or downloaded and used (...)

支援產品和硬體

支援產品和硬體
啟動 下載選項
設計工具

MSP-3P-SEARCH — MSP 第三方搜尋工具

TI has partnered with multiple companies to offer a wide range of solutions and services for TI MSP devices. These companies can accelerate your path to production using MSP devices. Download this search tool to quickly browse third-party details and find the right third-party to meet your needs.

(...)

下載
參考設計

TIDM-FRAM-EEPROM — 使用 MSP430 FRAM 微控制器實現 EEPROM 模擬和感測

此參考設計說明使用 MSP430™ 超低功耗微控制器 (MCU) 上的鐵電隨機存取記憶體 (FRAM) 技術，結合使用 MCU 時可啟用的其他感測功能，模擬電子可擦除可編程唯讀記憶體 (EEPROM) 的實作方式。此參考設計支援 I2C 及序列周邊介面 (SPI) 的介面，可連接具多個從屬位址的主機處理器。
Design guide: PDF
電路圖: PDF
封裝 針腳 CAD 符號、佔位空間與 3D 模型
LQFP (PM) 64 Ultra Librarian
TSSOP (DGG) 56 Ultra Librarian
TSSOP (DGG) 48 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

內含資訊：
  • RoHS
  • REACH
  • 產品標記
  • 鉛塗層/球物料
  • MSL 等級/回焊峰值
  • MTBF/FIT 估算值
  • 材料內容
  • 認證摘要
  • 進行中的可靠性監測
內含資訊：
  • 晶圓廠位置
  • 組裝地點

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片