首頁 音訊、觸覺和壓電 音訊放大器 車用音訊放大器
首頁
音訊、觸覺和壓電
音訊放大器
車用音訊放大器
最新

TAS67534-Q1

現行

具 1L 調變的車用、19V、數位輸入四通道 D 類音訊放大器

立即訂購
產品規格表

TAS67534-Q1

現行
產品規格表 立即訂購

產品詳細資料

Output power (W) 52 Power stage supply (max) (V) 19 Power stage supply (min) (V) 4.5 Speaker channels (max) 4 Features 1L modulation, Current sense, Low latency, real-time load diagnostics, thermal pad up Audio input type Digital Input Control interface I2C THD + N at 1 kHz (%) 0.02 Switching frequency (max) (Hz) 2000000 Output noise voltage (µV) 35 Sampling rate (max) (Hz) 192000 Rating Automotive Operating temperature range (°C) -40 to 125
Output power (W) 52 Power stage supply (max) (V) 19 Power stage supply (min) (V) 4.5 Speaker channels (max) 4 Features 1L modulation, Current sense, Low latency, real-time load diagnostics, thermal pad up Audio input type Digital Input Control interface I2C THD + N at 1 kHz (%) 0.02 Switching frequency (max) (Hz) 2000000 Output noise voltage (µV) 35 Sampling rate (max) (Hz) 192000 Rating Automotive Operating temperature range (°C) -40 to 125
HSSOP (DKQ) 56 190.647 mm² (18.42 mm × 10.35 mm)
  • AEC-Q100 qualified for automotive applications
    • Temperature grade 1: –40°C to +125°C, TA
  • General operation
    • 4.5V to 19V supply voltage, 40V load dump
    • Low latency path reducing group delay by >70% at 48kHz
    • Support for 1.8V and 3.3V I/Os
    • I2C control with 8 address options
  • 1L Modulation
    • Requires only one inductor per channel saving four inductors versus a traditional design
    • Lower system component cost for inductors
    • Smaller PCB footprint
  • Audio Performance
    • THD+N 0.02% (4Ω, 1W, 1kHz)
    • Output noise: 35µVRMS at 14.4V, A-weighting
    • Efficiency > 90% at 4 × 25W, 4Ω, 14.4V
  • Output current sensing by channel via I2S/TDM
    • No external circuitry needed
  • Real-time load diagnostics
    • Monitor output conditions while playing audio
    • Open Load, Shorted load, Short-to-power, and Short-to-ground detection
  • DC and AC Standby load diagnostics
  • Audio inputs
    • 2-4 channel I2S or 4-16 channel TDM input
    • Input sample rates: 44.1, 48, 96, 192kHz
  • Audio outputs
    • 4 channel bridge-tied load (BTL), configurable 2 channel parallel-BTL (PBTL)
    • 2MHz output switching frequency
    • 4 × 30W (4Ω, 14.4V, 1kHz, 10% THD+N)
    • 4 × 52W (2Ω, 14.4V, 1kHz, 10% THD+N)
  • Advanced spread-spectrum and selectable phase offset
  • Protection and monitoring
    • Cycle-by-cycle current limiting
    • Output short protection
    • Clip detection with configurable thresholds
    • Thermal foldback and PVDD foldback
    • I2C temperature and supply voltage readout
    • Configurable overtemperature warning and individual channel shutdown
    • DC offset, undervoltage and overvoltage
  • AEC-Q100 qualified for automotive applications
    • Temperature grade 1: –40°C to +125°C, TA
  • General operation
    • 4.5V to 19V supply voltage, 40V load dump
    • Low latency path reducing group delay by >70% at 48kHz
    • Support for 1.8V and 3.3V I/Os
    • I2C control with 8 address options
  • 1L Modulation
    • Requires only one inductor per channel saving four inductors versus a traditional design
    • Lower system component cost for inductors
    • Smaller PCB footprint
  • Audio Performance
    • THD+N 0.02% (4Ω, 1W, 1kHz)
    • Output noise: 35µVRMS at 14.4V, A-weighting
    • Efficiency > 90% at 4 × 25W, 4Ω, 14.4V
  • Output current sensing by channel via I2S/TDM
    • No external circuitry needed
  • Real-time load diagnostics
    • Monitor output conditions while playing audio
    • Open Load, Shorted load, Short-to-power, and Short-to-ground detection
  • DC and AC Standby load diagnostics
  • Audio inputs
    • 2-4 channel I2S or 4-16 channel TDM input
    • Input sample rates: 44.1, 48, 96, 192kHz
  • Audio outputs
    • 4 channel bridge-tied load (BTL), configurable 2 channel parallel-BTL (PBTL)
    • 2MHz output switching frequency
    • 4 × 30W (4Ω, 14.4V, 1kHz, 10% THD+N)
    • 4 × 52W (2Ω, 14.4V, 1kHz, 10% THD+N)
  • Advanced spread-spectrum and selectable phase offset
  • Protection and monitoring
    • Cycle-by-cycle current limiting
    • Output short protection
    • Clip detection with configurable thresholds
    • Thermal foldback and PVDD foldback
    • I2C temperature and supply voltage readout
    • Configurable overtemperature warning and individual channel shutdown
    • DC offset, undervoltage and overvoltage

The TAS67534-Q1 is a four-channel digital-input Class-D audio amplifier that implements 1L modulation only requiring one inductor per BTL channel reducing system size and cost by removing four inductors compared to a traditional design. Additionally, 1L modulation lowers switching losses compared to traditional Class-D modulation schemes.

The TAS67534-Q1 integrates DC and AC load diagnostics to determine the status of the connected loads. During audio playback this status can be monitored through Real-Time load diagnostics. The device also offers current sense for each channel and can report the measurement to a host processor through TDM with minimal delay. The device monitors the output load condition while playing audio through real-time load diagnostics independent of the host and audio input.

The TAS67534-Q1 device features an additional low latency signal path for each channel, providing up to 70% faster signal processing at 48kHz which enables time-sensitive active noise cancellation (ANC), road noise cancellation (RNC) applications.

The device supports global temperature, channel temperature and PVDD values using I2C readout for easy system level thermal management.

The device is offered in a 56-pin HSSOP package with the exposed thermal pad up.

The TAS67534-Q1 is a four-channel digital-input Class-D audio amplifier that implements 1L modulation only requiring one inductor per BTL channel reducing system size and cost by removing four inductors compared to a traditional design. Additionally, 1L modulation lowers switching losses compared to traditional Class-D modulation schemes.

The TAS67534-Q1 integrates DC and AC load diagnostics to determine the status of the connected loads. During audio playback this status can be monitored through Real-Time load diagnostics. The device also offers current sense for each channel and can report the measurement to a host processor through TDM with minimal delay. The device monitors the output load condition while playing audio through real-time load diagnostics independent of the host and audio input.

The TAS67534-Q1 device features an additional low latency signal path for each channel, providing up to 70% faster signal processing at 48kHz which enables time-sensitive active noise cancellation (ANC), road noise cancellation (RNC) applications.

The device supports global temperature, channel temperature and PVDD values using I2C readout for easy system level thermal management.

The device is offered in a 56-pin HSSOP package with the exposed thermal pad up.
filter 尋找其它 車用音訊放大器
下載 觀看有字幕稿的影片 影片

提供完整資料表及其他設計資源。立即索取

技術文件

找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 1
重要文件 類型 標題 格式選項 下載最新的英文版本 日期
* 資料表 TAS67534-Q1 ​​​1L Modulation, 52 W, 2MHz Digital Input 4 -Channel Automotive Class-D Audio Amplifier With Current Sense and Real-time Load Diagnostics datasheet PDF | HTML 2026/8/27

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

TAS67534Q1EVM — TAS67534-Q1 評估模組

TAS67534Q1EVM 展示了 TAS67534-Q1，具有 1L 調變功能的四通道、數位輸入閉合迴路 D 類車用音訊放大器，可在每通道減少 1 個電感器，並可為四通道減少 50% 的電感器成本。EVM 在編程和 I2C 配置中使用 PurePath™ Console (PPC3) 圖形使用者介面，以評估 TAS67534-Q1 裝置的特性、功能和性能。

支援產品和硬體
支援軟體

TAS67534-Q1-DESIGN — TAS67534-Q1 Technical Documentation

TAS67534-Q1 Technical Documentation
支援產品和硬體
認證

TAS67534-Q1EVM-DOC-CERT — TAS67534-Q1EVM 歐盟符合性聲明 (DoC)

TAS67534-Q1EVM EU Declaration of Conformity (DoC)
支援產品和硬體
封裝 針腳 CAD 符號、佔位空間與 3D 模型
HSSOP (DKQ) 56 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片