TUSB2E221
- Compliance to USB 2.0 and eUSB2 (rev 1.2)
- Support for low-speed (LS), full-speed (FS), high-speed (HS)
- Best-in-class high-speed total jitter of 20ps
- Register access protocol receptor capable
- Dual independent repeater
- 2:2 crossbar mux (DSBGA package only)
- Host and device mode (DRD) support
- Selection between 1.2V and 1.8V control or I2C levels using VIOSEL pin
- Auto detection for I2C or strap-pin options
- Three strap-pins for USB 2.0 high-speed channel compensation settings
- I2C device interface for more configurations
- Device variants
- eUSB2 1.0V or 1.2V signaling interface
- Four eUSB2 trace loss compensation levels for different product form-factors: 2.5, 5, 7.5, and 10 inches
- Supports auto-resume ECR as well as L2 interrupt resume mode
- CTA-936 USB Carkit UART support
- Optional BC1.2 CDP battery charging and detection support
- Optional GPIO modes for EQ pins for debug and I2C ↔ GPIOs through EQ0/1
- I2C accessible debug capabilities for manufacturing tests
The TUSB2E221 enables implementation of USB 2.0 compliant port on newer processors using lower voltage processes.
The TUSB2E221 is a USB eUSB2-USB 2.0 repeater supporting both device and host modes. The TUSB2E221 supports USB low-speed (LS) and full-speed (FS) signals and high-speed (HS) signals.
The TUSB2E221 is designed to interface with eUSB2 eDSPr or eUSPr operating at 1.2V single-ended signaling.
The TUSB2E221 has multiple patented designs to provide robust interoperability, optimum performance, and power.
For systems without an I2C interface, the device offers eight individual settings with three strap-pins for USB 2.0 channel Equivalent Series Resistance (ESR) up to 17.5Ω. Device variants are available for different levels of eUSB2 trace length compensation up to 10 inches.
The I2C interface permits additional flexibility for users to fine tune the RX and TX settings of the device. The available settings are RX equalization, RX squelch threshold, RX disconnect thresholds, TX amplitude, TX slew rate and TX pre-emphasis.
Various debug options are available through the three EQ pins that can be configured to monitor various USB bus states or interrupt as well as CTA-936 UART mode control that can provide SoC debug capabilities. EQ0 and EQ1 can be used as general purpose I2C to GPIOs bridge.
技術文件
| 類型 | 標題 | 日期 | ||
|---|---|---|---|---|
| * | Data sheet | TUSB2E221 USB 2.0-eUSB2 Dual Repeater datasheet (Rev. D) | PDF | HTML | 2025年 10月 22日 |
| Certificate | TUSB2E221QFNEVM EU Declaration of Conformity (DoC) | 2024年 11月 11日 | ||
| Application brief | Top Four Things to Know About eUSB2 | PDF | HTML | 2024年 7月 24日 |
設計與開發
如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。
TUSB2E221QFNEVM — TUSB2E221QFN 評估模組
TUSB2E221QFN 評估模組 (EVM) 的設計可協助評估和驗證 TUSB2E221 雙埠 eUSB 中繼器的性能。此 EVM 整合堆疊式 Type-A USB 2.0 連接器，可連接至 USB 相容主機（使用 Type-A 轉 B 轉接器）、集線器或裝置。EVM 也有兩組 SMP 連接器，可與另一個 eUSB2 PHY 或測試設備接合。
PSPICE-FOR-TI — PSpice® for TI 設計與模擬工具
PSpice for TI 設計和模擬環境可讓您使用其內建函式庫來模擬複雜的混合訊號設計。在進行佈局和製造之前，建立完整的終端設備設計和解決方案原型，進而縮短上市時間並降低開發成本。
在 PSpice for TI 設計與模擬工具中，您可以搜尋 TI (...)
TINA-TI — 基於 SPICE 的類比模擬程式
| 封裝 | 針腳 | CAD 符號、佔位空間與 3D 模型 |
|---|---|---|
| DSBGA (YCG) | 25 | Ultra Librarian |
| WQFN-FCRLF (VBW) | 20 | Ultra Librarian |
訂購與品質
- RoHS
- REACH
- 產品標記
- 鉛塗層/球物料
- MSL 等級/回焊峰值
- MTBF/FIT 估算值
- 材料內容
- 認證摘要
- 進行中持續性的可靠性監測
- 晶圓廠位置
- 組裝地點
建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。