SNIS214E june   2021  – july 2023 TMP114

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Revision History
  6. 5 Device Comparison
  7. 6 Pin Configuration and Functions
  8. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 I2C Interface Timing
    7. 7.7 Typical Characteristics
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 1.2 V Compatible Logic Inputs
      2. 8.3.2 Cyclic Redundancy Check (CRC)
      3. 8.3.3 Temperature Limits
      4. 8.3.4 Slew Rate Warning
      5. 8.3.5 NIST Traceability
    4. 8.4 Device Functional Modes
      1. 8.4.1 Continuous Conversion Mode
      2. 8.4.2 Shutdown Mode
        1. 8.4.2.1 One-Shot Temperature Conversions
    5. 8.5 Programming
      1. 8.5.1 Temperature Data Format
      2. 8.5.2 I2C and SMBus Interface
      3. 8.5.3 Device Address
      4. 8.5.4 Bus Transactions
        1. 8.5.4.1 Auto-Increment
        2. 8.5.4.2 Writes
          1. 8.5.4.2.1 CRC Enabled Writes
        3. 8.5.4.3 Reads
          1. 8.5.4.3.1 CRC Enabled Reads
        4. 8.5.4.4 General Call Reset Function
        5. 8.5.4.5 Time-Out Function
        6. 8.5.4.6 Coexist on I3C MixedBus
        7. 8.5.4.7 Cyclic Redundancy Check Implementation
    6. 8.6 Register Map
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Separate I2C Pullup and Supply Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
      3. 9.2.3 Application Curves
    3. 9.3 Equal I2C Pullup and Supply Voltage Application
      1. 9.3.1 Design Requirements
      2. 9.3.2 Detailed Design Procedure
    4. 9.4 Power Supply Recommendations
    5. 9.5 Layout
      1. 9.5.1 Layout Guidelines
      2. 9.5.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Receiving Notification of Documentation Updates
    2. 10.2 Support Resources
    3. 10.3 Trademarks
    4. 10.4 Electrostatic Discharge Caution
    5. 10.5 Glossary
  12. 11Mechanical, Packaging, and Orderable Information

Package Options

Refer to the PDF data sheet for device specific package drawings

Mechanical Data (Package|Pins)
  • YMT|4
Thermal pad, mechanical data (Package|Pins)
Orderable Information

8.4.1 Continuous Conversion Mode

When the Mode bit is set to 0b in the configuration register, the device operates in continuous conversion mode. Figure 8-4 shows the device in a continuous conversion cycle. In this mode, the device can perform multiple conversions and updates the temperature result register and Data_Ready_Flag in the alert status register at the end of every active conversion. The typical active conversion time for the device is 6.4 ms with averaging disabled. When averaging is enabled, the device will convert 8 consecutive times at the beginning of every conversion period for a typical time of 51.2 ms.

GUID-14BC69E2-D81C-4FB3-B6D4-549F844E41BF-low.gif Figure 8-4 Continuous Conversion Cycle Timing Diagram

The Conv_Period[1:0] bits in the configuration register control the rate at which the conversions are performed. The device typically consumes 68 µA during conversion and 0.26 µA during the low power standby period. By decreasing the rate at which the conversions are performed, the application can benefit from reduced average current consumption in continuous mode.

Use Equation 1 to calculate the average current in continuous mode.

Equation 1. Average Current = ((IACT × tACTIVE) + (IStandby × tStandby)) / tConv_Period

Where

  • tACTIVE = Active Conversion Time
  • tConv_Period = Conversion Period
  • tStandby = Standby time between conversions calculate as tConv_Period – tACTIVE