SBOSA45C february   2022  – may 2023 TMP1826

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Revision History
  6. 5 Description (cont.)
  7. 6 Device Comparison
  8. 7 Pin Configuration and Functions
  9. 8 Specifications
    1. 8.1 Absolute Maximum Ratings
    2. 8.2 ESD Ratings
    3. 8.3 Recommended Operating Conditions
    4. 8.4 Thermal Information
    5. 8.5 Electrical Characteristics
    6. 8.6 1-Wire Interface Timing
    7. 8.7 EEPROM Characteristics
    8. 8.8 Timing Diagrams
    9. 8.9 Typical Characteristics
  10. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1  Power Up
      2. 9.3.2  Power Mode Switch
      3. 9.3.3  Bus Pullup Resistor
      4. 9.3.4  Temperature Results
      5. 9.3.5  Temperature Offset
      6. 9.3.6  Temperature Alert
      7. 9.3.7  Standard Device Address
        1. 9.3.7.1 Unique 64-Bit Device Address and ID
      8. 9.3.8  Flexible Device Address
        1. 9.3.8.1 Non-Volatile Short Address
        2. 9.3.8.2 IO Hardware Address
        3. 9.3.8.3 Resistor Address
        4. 9.3.8.4 Combined IO and Resistor Address
      9. 9.3.9  CRC Generation
      10. 9.3.10 Functional Register Map
      11. 9.3.11 User Memory Map
      12. 9.3.12 Bit Communication
        1. 9.3.12.1 Host Write, Device Read
        2. 9.3.12.2 Host Read, Device Write
      13. 9.3.13 Bus Speed
      14. 9.3.14 NIST Traceability
    4. 9.4 Device Functional Modes
      1. 9.4.1 Conversion Modes
        1. 9.4.1.1 Basic One-Shot Conversion Mode
        2. 9.4.1.2 Auto Conversion Mode
        3. 9.4.1.3 Stacked Conversion Mode
        4. 9.4.1.4 Continuous Conversion Mode
      2. 9.4.2 Alert Function
        1. 9.4.2.1 Alert Mode
        2. 9.4.2.2 Comparator Mode
      3. 9.4.3 1-Wire Interface Communication
        1. 9.4.3.1 Bus Reset Phase
        2. 9.4.3.2 Address Phase
          1. 9.4.3.2.1 READADDR (33h)
          2. 9.4.3.2.2 MATCHADDR (55h)
          3. 9.4.3.2.3 SEARCHADDR (F0h)
          4. 9.4.3.2.4 ALERTSEARCH (ECh)
          5. 9.4.3.2.5 SKIPADDR (CCh)
          6. 9.4.3.2.6 OVD SKIPADDR (3Ch)
          7. 9.4.3.2.7 OVD MATCHADDR (69h)
          8. 9.4.3.2.8 FLEXADDR (0Fh)
        3. 9.4.3.3 Function Phase
          1. 9.4.3.3.1  CONVERTTEMP (44h)
          2. 9.4.3.3.2  WRITE SCRATCHPAD-1 (4Eh)
          3. 9.4.3.3.3  READ SCRATCHPAD-1 (BEh)
          4. 9.4.3.3.4  COPY SCRATCHPAD-1 (48h)
          5. 9.4.3.3.5  WRITE SCRATCHPAD-2 (0Fh)
          6. 9.4.3.3.6  READ SCRATCHPAD-2 (AAh)
          7. 9.4.3.3.7  COPY SCRATCHPAD-2 (55h)
          8. 9.4.3.3.8  READ EEPROM (F0h)
          9. 9.4.3.3.9  GPIO WRITE (A5h)
          10. 9.4.3.3.10 GPIO READ (F5h)
      4. 9.4.4 NVM Operations
        1. 9.4.4.1 Programming User Data
        2. 9.4.4.2 Register and Memory Protection
          1. 9.4.4.2.1 Scratchpad-1 Register Protection
          2. 9.4.4.2.2 User Memory Protection
    5. 9.5 Programming
      1. 9.5.1 Single Device Temperature Conversion and Read
      2. 9.5.2 Multiple Device Temperature Conversion and Read
      3. 9.5.3 Register Scratchpad-1 Update and Commit
      4. 9.5.4 Single Device EEPROM Programming and Verify
      5. 9.5.5 Single Device EEPROM Page Lock Operation
      6. 9.5.6 Multiple Device IO Read
      7. 9.5.7 Multiple Device IO Write
    6. 9.6 Register Map
      1. 9.6.1  Temperature Result LSB Register (Scratchpad-1 offset = 00h) [reset = 00h]
      2. 9.6.2  Temperature Result MSB Register (Scratchpad-1 offset = 01h) [reset = 00h]
      3. 9.6.3  Status Register (Scratchpad-1 offset = 02h) [reset = 3Ch]
      4. 9.6.4  Device Configuration-1 Register (Scratchpad-1 offset = 04h) [reset = 70h]
      5. 9.6.5  Device Configuration-2 Register (Scratchpad-1 offset = 05h) [reset = 80h]
      6. 9.6.6  Short Address Register (Scratchpad-1 offset = 06h) [reset = 00h]
      7. 9.6.7  Temperature Alert Low LSB Register (Scratchpad-1 offset = 08h) [reset = 00h]
      8. 9.6.8  Temperature Alert Low MSB Register (Scratchpad-1 offset = 09h) [reset = 00h]
      9. 9.6.9  Temperature Alert High LSB Register (Scratchpad-1 offset = 0Ah) [reset = F0h]
      10. 9.6.10 Temperature Alert High MSB Register (Scratchpad-1 offset = 0Bh) [reset = 07h]
      11. 9.6.11 Temperature Offset LSB Register (Scratchpad-1 offset = 0Ch) [reset = 00h]
      12. 9.6.12 Temperature Offset MSB Register (Scratchpad-1 offset = 0Dh) [reset = 00h]
      13. 9.6.13 IO Read Register [reset = F0h]
      14. 9.6.14 IO Configuration Register [reset = 00h]
  11. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Applications
      1. 10.2.1 Bus Powered Application
        1. 10.2.1.1 Design Requirements
        2. 10.2.1.2 Detailed Design Procedure
      2. 10.2.2 Supply Powered Application
        1. 10.2.2.1 Design Requirements
        2. 10.2.2.2 Detailed Design Procedure
      3. 10.2.3 UART Interface for Communication
        1. 10.2.3.1 Design Requirements
        2. 10.2.3.2 Detailed Design Procedure
    3. 10.3 Power Supply Recommendations
    4. 10.4 Layout
      1. 10.4.1 Layout Guidelines
      2. 10.4.2 Layout Example
  12. 11Device and Documentation Support
    1. 11.1 Documentation Support
      1. 11.1.1 Related Documentation
    2. 11.2 Receiving Notification of Documentation Updates
    3. 11.3 Support Resources
    4. 11.4 Trademarks
    5. 11.5 Electrostatic Discharge Caution
    6. 11.6 Glossary
  13. 12Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

9.5.3 Register Scratchpad-1 Update and Commit

Table 9-8 shows the sequence the host must execute to update the register scratchpad and commit to the configuration EEPROM. The host must read the scratchpad to ensure it can perform the correct read modify write to the registers, before it copies the same to the configuration EEPROM.

If the host has only one device, or if the application can guarantee no bus corruption, then it may use SKIPADDR command to globally update and commit the register scratchpad region with the same settings. However once committed and locked, it is not possible for the host to update the locations anymore, and hence TI strongly advises that the host still read the locations before running the commit operation.

Table 9-8 Register Scratchpad-1 Update and Program Configuration EEPROM
HOST TO DEVICE DEVICE TO HOST COMMENTS
Reset Host sends reset to initialize communication
Answer to Reset Device responds to initialization
MATCHADDR (55h) Host sends address command to select specific device
DEVICE-1 ADDRESS Host sends 8 byte for selecting device-1
READ SCRATCHPAD-1 (BEh) Host sends function command to read register scratchpad-1
16 register bytes + 2 CRC bytes Device sends first 8 register scratchpad-1 bytes followed by CRC byte and then last 8 register scratchpad-1 bytes followed by CRC byte
Reset
Answer to Reset Device responds to initialization
MATCHADDR (55h) Host sends address command to select specific device
DEVICE-1 ADDRESS Host sends 8 byte for selecting device-1
WRITE SCRATCHPAD-1 (4Eh) Host sends function command to write register scratchpad-1
9 register bytes Host sends the updated 9 register scratchpad-1 bytes
CRC Device sends CRC for the register bytes
Reset Host sends reset to initialize communication
Answer to Reset Device responds to initialization
MATCHADDR (55h) Host sends address command to select specific device
DEVICE-1 ADDRESS Host sends 8 byte for selecting device-1
COPY SCRATCHPAD-1 (48h) Host sends function command to write copy scratchpad-1 to configuration EEPROM
Bus idle for tPROG for register Bus is held in idle state (high) during configuration EEPROM erase-program