SLLSFN5A June   2023  – February 2024 ISO1228

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
    4. 5.4  Thermal Information
    5. 5.5  Power Ratings
    6. 5.6  Insulation Specifications
    7. 5.7  Safety-Related Certifications
    8. 5.8  Safety Limiting Values
    9. 5.9  Electrical Characteristics—DC Specification
    10. 5.10 Switching Characteristics—AC Specification
    11. 5.11 Typical Characteristics
  7. 6 Parameter Measurement Information
    1. 6.1 Test Circuits
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Surge Protection
      2. 7.3.2  Field Side LED Indication
      3. 7.3.3  Serial and Parallel Output option
      4. 7.3.4  Cyclic Redundancy Check (CRC)
      5. 7.3.5  FAULT Indication
      6. 7.3.6  Digital Low Pass Filter
      7. 7.3.7  SPI Register Map
      8. 7.3.8  SPI Interface Timing - Non-Daisy Chain
      9. 7.3.9  SPI Interface Timing - Daisy Chain
      10. 7.3.10 SPI Interface Timing - Burst Mode
    4. 7.4 Device Functional Modes
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Sinking Type Digital Inputs
      2. 8.2.2 Sourcing Type Digital Inputs
      3. 8.2.3 Design Requirements
        1. 8.2.3.1 Detailed Design Procedure
          1. 8.2.3.1.1 Current Limit
          2. 8.2.3.1.2 Voltage Thresholds
          3. 8.2.3.1.3 Wire-Break Detection
  10. 9 Power Supply Recommendations
  11. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  12. 11Device and Documentation Support
    1. 11.1 Documentation Support
      1. 11.1.1 Related Documentation
    2. 11.2 Receiving Notification of Documentation Updates
    3. 11.3 Support Resources
    4. 11.4 Trademarks
    5. 11.5 Electrostatic Discharge Caution
    6. 11.6 Glossary
  13. 12Revision History
  14. 13Mechanical, Packaging, and Orderable Information
    1. 13.1 Tape and Reel Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

7.3.6 Digital Low Pass Filter

The ISO1228 supports in-built digital low pass filters on the INx and WBx data paths. The filters can be programmed through SPI registers (where each channel filter can be individually programmed) or through the pins F0 and F1. F0 and F1 pins support three input states, high, low, and float, resulting in 9 values of digital filtering. Refer to the Switching Characteristics section for values of the digital filters. The filter values in the SPI registers take precedence. If any SPI filter Enable has a non-zero value, then the states of F0 and F1 pins are ignored.

ISO1228 also supports a digital filter on the Wire Break detection fault. This is a fixed, non-programmable, 30ms filter.