SWRS219 Data sheet

SWRS219F October 2018 – April 2025 IWR6443 , IWR6843

PRODUCTION DATA

Package Options

Refer to the PDF data sheet for device specific package drawings

Mechanical Data (Package|Pins)

ABL|161

Thermal pad, mechanical data (Package|Pins)

Orderable Information

7.12.3.3.1 SPI Peripheral Mode Switching Parameters (SPICLK = input, SPISIMO = input,
and SPISOMI = output)⁽¹⁾⁽²⁾⁽³⁾

NO.	PARAMETER		MIN	MAX	UNIT
1	t_c(SPC)S	Cycle time, SPICLK⁽⁴⁾	25		ns
2⁽⁵⁾	t_w(SPCH)S	Pulse duration, SPICLK high (clock polarity = 0)	10		ns
2⁽⁵⁾	t_w(SPCL)S	Pulse duration, SPICLK low (clock polarity = 1)	10		ns
3⁽⁵⁾	t_w(SPCL)S	Pulse duration, SPICLK low (clock polarity = 0)	10		ns
3⁽⁵⁾	t_w(SPCH)S	Pulse duration, SPICLK high (clock polarity = 1)	10		ns
4⁽⁵⁾	t_{d(SPCH-SOMI)S}	Delay time, SPISOMI valid after SPICLK high (clock polarity = 0)		10	ns
4⁽⁵⁾	t_{d(SPCL-SOMI)S}	Delay time, SPISOMI valid after SPICLK low (clock polarity = 1)		10	ns
5⁽⁵⁾	t_{h(SPCH-SOMI)S}	Hold time, SPISOMI data valid after SPICLK high (clock polarity = 0)	2		ns
5⁽⁵⁾	t_{h(SPCL-SOMI)S}	Hold time, SPISOMI data valid after SPICLK low (clock polarity = 1)	2		ns
4⁽⁵⁾	t_{d(SPCH-SOMI)S}	Delay time, SPISOMI valid after SPICLK high (clock polarity = 0; clock phase = 0) OR (clock polarity = 1; clock phase = 1)		10	ns
4⁽⁵⁾	t_{d(SPCL-SOMI)S}	Delay time, SPISOMI valid after SPICLK low (clock polarity = 1; clock phase = 0) OR (clock polarity = 0; clock phase = 1)		10	ns
5⁽⁵⁾	t_{h(SPCH-SOMI)S}	Hold time, SPISOMI data valid after SPICLK high (clock polarity = 0; clock phase = 0) OR (clock polarity = 1; clock phase = 1)	2		ns
5⁽⁵⁾	t_{h(SPCL-SOMI)S}	Hold time, SPISOMI data valid after SPICLK low (clock polarity = 1; clock phase = 0) OR (clock polarity = 0; clock phase = 1)	2		ns
6⁽⁵⁾	t_{su(SIMO-SPCL)S}	Setup time, SPISIMO before SPICLK low (clock polarity = 0; clock phase = 0) OR (clock polarity = 1; clock phase = 1)	3		ns
6⁽⁵⁾	t_{su(SIMO-SPCH)S}	Setup time, SPISIMO before SPICLK high (clock polarity = 1; clock phase = 0) OR (clock polarity = 0; clock phase = 1)	3		ns
7⁽⁵⁾	t_{h(SPCL-SIMO)S}	Hold time, SPISIMO data valid after SPICLK low (clock polarity = 0; clock phase = 0) OR (clock polarity = 1; clock phase = 1)	1		ns
7⁽⁵⁾	t_{h(SPCL-SIMO)S}	Hold time, SPISIMO data valid after SPICLK high (clock polarity = 1; clock phase = 0) OR (clock polarity = 0; clock phase = 1)	1		ns

(1) The MASTER bit (SPIGCRx.0) is cleared ( where x = 0 or 1 ).

(2) The CLOCK PHASE bit (SPIFMTx.16) is either cleared or set for CLOCK PHASE = 0 or CLOCK PHASE = 1 respectively.

(3) t_{c(MSS_VCLK)} = main subsystem clock time = 1 / f_{(MSS_VCLK)}. For more details, see the Technical Reference Manual.

(4) When the SPI is in peripheral mode, the following must be true: For PS values from 1 to 255: t_c(SPC)S ≥ (PS +1)t_{c(MSS_VCLK)} ≥ 25 ns, where PS is the prescale value set in the SPIFMTx.[15:8] register bits.For PS values of 0: t_c(SPC)S = 2t_{c(MSS_VCLK)} ≥ 25 ns.

(5) The active edge of the SPICLK signal referenced is controlled by the CLOCK POLARITY bit (SPIFMTx.17).

IWR6843 IWR6443 SPI peripheral Mode
External Timing (CLOCK PHASE = 0)

Figure 7-9 SPI peripheral Mode External Timing (CLOCK PHASE = 0)

IWR6843 IWR6443 SPI peripheral Mode
External Timing (CLOCK PHASE = 1)

Figure 7-10 SPI peripheral Mode External Timing (CLOCK PHASE = 1)

Package Options

Mechanical Data (Package|Pins)

Thermal pad, mechanical data (Package|Pins)

Orderable Information

7.12.3.3.1 SPI Peripheral Mode Switching Parameters (SPICLK = input, SPISIMO = input, and SPISOMI = output)(1)(2)(3)

7.12.3.3.1 SPI Peripheral Mode Switching Parameters (SPICLK = input, SPISIMO = input,
and SPISOMI = output)⁽¹⁾⁽²⁾⁽³⁾