SBOSAJ5 December   2024 TMP113

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Related Products
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 I2C Interface Timing
    7. 6.7 Timing Diagrams
    8. 6.8 Typical Characteristics
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Digital Temperature Output
      2. 7.3.2 Decoding Temperature Data
      3. 7.3.3 Temperature Limits and Alert
      4. 7.3.4 NIST Traceability
    4. 7.4 Device Functional Modes
      1. 7.4.1 Continuous-Conversion Mode
      2. 7.4.2 One-Shot Mode
    5. 7.5 Programming
      1. 7.5.1 Serial Interface
      2. 7.5.2 Bus Overview
      3. 7.5.3 Device Address
      4. 7.5.4 Bus Transactions
        1. 7.5.4.1 Writes
        2. 7.5.4.2 Reads
        3. 7.5.4.3 General Call Reset Function
        4. 7.5.4.4 SMBus Alert Response
        5. 7.5.4.5 Time-Out Function
        6. 7.5.4.6 Coexist on I3C Mixed Bus
  9. 8 Register Map
    1. 8.1 Temp_Result Register (address = 00h) [reset = 0000h]
    2. 8.2 Configuration Register (address = 01h) [reset = 40A0h]
    3. 8.3 TLow_Limit Register (address = 02h) [reset = 4B00h]
    4. 8.4 THigh_Limit Register (address = 03h) [reset = 5000h]
    5. 8.5 Device ID Register (Address = 0Bh) [reset = 113xh]
    6. 8.6 Unique_ID0 Register (Address = 0Ch) [reset = xxxxh]
    7. 8.7 Unique_ID1 Register (Address = 0Dh) [reset = xxxxh]
    8. 8.8 Unique_ID2 Register (Address = 0Eh) [reset = xxxxh]
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Equal I2C Pullup and Supply Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
      3. 9.2.3 Application Curve
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Device Support
    2. 10.2 Documentation Support
      1. 10.2.1 Related Documentation
    3. 10.3 Receiving Notification of Documentation Updates
    4. 10.4 Support Resources
    5. 10.5 Electrostatic Discharge Caution
    6. 10.6 Glossary
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information
    1. 12.1 Package Option Addendum
    2. 12.2 Tape and Reel Information

Package Options

Refer to the PDF data sheet for device specific package drawings

Mechanical Data (Package|Pins)
  • YBG|6
Thermal pad, mechanical data (Package|Pins)
Orderable Information

7.4.1 Continuous-Conversion Mode

When the Shutdown bit is set to 0b in the configuration register, the device operates in continuous conversion mode. Figure 7-3 shows the device in a continuous conversion cycle. In this mode, the device performs conversion at fixed periods and updates the temperature result register at the end of every conversion, The typical active conversion time is 11ms.

TMP113 Continuous Conversion Cycle Timing DiagramFigure 7-3 Continuous Conversion Cycle Timing Diagram

The Conversion_Rate[1:0] bits in the configuration register control the rate at which the conversions are performed. The device typically consumes 55µA during conversion and 0.85µA during the low power standby time. By decreasing the rate at which conversions are performed, the application can benefit from reduced average current consumption in continuous mode.

Use Equation 1 to calculate the average current in continuous mode.

Equation 1. Average Current = ((IDD_ACTIVE × tACT) + (IDD_SB × tSTANDBY)) / tConv_Period

Where

  • tACT = Active conversion time
  • tConv_Period = Conversion Period
  • tSTANDBY = Standby time between conversions calculated as tConv_Period - tACT