SBVS263B July   2017  – June 2025 TPS7A39

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Start-Up Characteristics
    7. 5.7 Timing Diagram
    8. 5.8 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 Voltage Regulation
        1. 6.3.1.1 DC Regulation
        2. 6.3.1.2 AC and Transient Response
      2. 6.3.2 User-Settable Buffered Reference
      3. 6.3.3 Active Discharge
      4. 6.3.4 System Start-Up Controls
        1. 6.3.4.1 Start-Up Tracking
        2. 6.3.4.2 Sequencing
          1. 6.3.4.2.1 Enable (EN)
          2. 6.3.4.2.2 Undervoltage Lockout (UVLO) Control
    4. 6.4 Device Functional Modes
      1. 6.4.1 Normal Operation
      2. 6.4.2 Dropout Operation
      3. 6.4.3 Disabled
  8. 7 Application and Implementation
    1. 7.1 Application Information
      1. 7.1.1  Setting the Output Voltages on Adjustable Devices
      2. 7.1.2  Capacitor Recommendations
      3. 7.1.3  Input and Output Capacitor (CINx and COUTx)
      4. 7.1.4  Feed-Forward Capacitor (CFFx)
      5. 7.1.5  Noise-Reduction and Soft-Start Capacitor (CNR/SS)
      6. 7.1.6  Buffered Reference Voltage
      7. 7.1.7  Overriding Internal Reference
      8. 7.1.8  Start-Up
        1. 7.1.8.1 Soft-Start Control (NR/SS)
          1. 7.1.8.1.1 In-Rush Current
        2. 7.1.8.2 Undervoltage Lockout (UVLOx) Control
      9. 7.1.9  AC and Transient Performance
        1. 7.1.9.1 Power-Supply Rejection Ratio (PSRR)
        2. 7.1.9.2 Channel-to-Channel Output Isolation and Crosstalk
        3. 7.1.9.3 Output Voltage Noise
        4. 7.1.9.4 Optimizing Noise and PSRR
        5. 7.1.9.5 Load Transient Response
      10. 7.1.10 DC Performance
        1. 7.1.10.1 Output Voltage Accuracy (VOUT x)
        2. 7.1.10.2 Dropout Voltage (VDO)
      11. 7.1.11 Reverse Current
      12. 7.1.12 Power Dissipation (PD)
        1. 7.1.12.1 Estimating Junction Temperature
    2. 7.2 Typical Applications
      1. 7.2.1 Design 1: Single-Ended to Differential Isolated Supply
        1. 7.2.1.1 Design Requirements
        2. 7.2.1.2 Detailed Design Procedure
          1. 7.2.1.2.1 Switcher Choice
          2. 7.2.1.2.2 Full Bridge Rectifier With Center-Tapped Transformer
          3. 7.2.1.2.3 Total Solution Efficiency
          4. 7.2.1.2.4 Feedback Resistor Selection
        3. 7.2.1.3 Application Curves
      2. 7.2.2 Design 2: Getting the Full Range of a SAR ADC
        1. 7.2.2.1 Design Requirements
        2. 7.2.2.2 Detailed Design Procedure
        3. 7.2.2.3 Detailed Design Description
          1. 7.2.2.3.1 Regulation of –0.2V
          2. 7.2.2.3.2 Feedback Resistor Selection
        4. 7.2.2.4 Application Curves
    3. 7.3 Power Supply Recommendations
    4. 7.4 Layout
      1. 7.4.1 Layout Guidelines
        1. 7.4.1.1 Board Layout Recommendations to Improve PSRR and Noise Performance
        2. 7.4.1.2 Package Mounting
      2. 7.4.2 Layout Example
  9. 8 Device and Documentation Support
    1. 8.1 Device Support
      1. 8.1.1 Development Support
        1. 8.1.1.1 Evaluation Modules
        2. 8.1.1.2 Spice Models
    2. 8.2 Documentation Support
      1. 8.2.1 Related Documentation
    3. 8.3 Receiving Notification of Documentation Updates
    4. 8.4 Support Resources
    5. 8.5 Trademarks
    6. 8.6 Electrostatic Discharge Caution
    7. 8.7 Glossary
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information
7.2.2.3.2 Feedback Resistor Selection

Use Equation 17 and Equation 18 to calculate the values of the feedback resistors:

Equation 17. VOUTP = VFBP × (1 + R1P / R2P)
Equation 18. VOUTN = VBUF × (–R1N / R2N)

For this design the recommended 10kΩ resistors are used for R2P and R2N. R1P and R1N can be calculated by substituting R2P and R2N into Equation 19 and Equation 20 because R2P and R2N are already selected.

Equation 19. R1P = [(VOUTP / VFBP) – 1] × R2P = [(5.2V / 1.188V) – 1] × 10kΩ = 33.8kΩ
Equation 20. R1N = –VOUTN × R2N / VBUF = –(–0.2V) × 10kΩ / 1.19V = 1.68kΩ

After solving for Equation 19 and Equation 20, the closest one percent resistors are selected, R1N = 1.69kΩ and R1P = 34kΩ.