SLASFB7A November   2024  – August 2025 TAS5802

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5.   Device Comparison Table
  6. 4 Pin Configuration and Functions
  7. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements
    7. 5.7 Typical Characteristics
      1. 5.7.1 Bridge Tied Load (BTL) Configuration Curves with 1SPW Modulation
      2. 5.7.2 Bridge Tied Load (BTL) Configuration Curves with BD Modulation
  8. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 Power Supplies
      2. 6.3.2 Device Clocking
      3. 6.3.3 Serial Audio Port – Clock Rates
      4. 6.3.4 Serial Audio Port (SAP)
      5. 6.3.5 Digital Audio Processing
      6. 6.3.6 Class D Audio Amplifier
        1. 6.3.6.1 Speaker Amplifier Gain Select
    4. 6.4 Device Functional Modes
      1. 6.4.1 Software Control
      2. 6.4.2 Speaker Amplifier Operating Modes
        1. 6.4.2.1 BTL Mode
      3. 6.4.3 Low EMI Modes
        1. 6.4.3.1 Spread Spectrum
        2. 6.4.3.2 Channel to Channel Phase Shift
        3. 6.4.3.3 Multi-Devices PWM Phase Synchronization
      4. 6.4.4 Thermal Foldback
      5. 6.4.5 Device State Control
      6. 6.4.6 Device Modulation
        1. 6.4.6.1 BD Modulation
        2. 6.4.6.2 1SPW Modulation
        3. 6.4.6.3 Hybrid Modulation
    5. 6.5 Programming and Control
      1. 6.5.1 I2C Serial Communication Bus
      2. 6.5.2 Target Address
        1. 6.5.2.1 Random Write
        2. 6.5.2.2 Sequential Write
        3. 6.5.2.3 Random Read
        4. 6.5.2.4 Sequential Read
        5. 6.5.2.5 DSP Memory Book, Page and BQ update
        6. 6.5.2.6 Checksum
          1. 6.5.2.6.1 Cyclic Redundancy Check (CRC) Checksum
          2. 6.5.2.6.2 Exclusive or (XOR) Checksum
      3. 6.5.3 Control via Software
        1. 6.5.3.1 Startup Procedures
        2. 6.5.3.2 Shutdown Procedures
        3. 6.5.3.3 Protection and Monitoring
          1. 6.5.3.3.1 Overcurrent Shutdown (OCSD)
          2. 6.5.3.3.2 DC Detect
          3. 6.5.3.3.3 Device Over Temperature Protection
          4. 6.5.3.3.4 Over Voltage Protection
          5. 6.5.3.3.5 Under Voltage Protection
          6. 6.5.3.3.6 Clock Fault
  9. 7 Register Maps
    1. 7.1 CONTROL PORT Registers
  10. 8 Application and Implementation
    1. 8.1 Application Information
      1. 8.1.1 Bootstrap Capacitors
      2. 8.1.2 Inductor Selections
      3. 8.1.3 Power Supply Decoupling
      4. 8.1.4 Output EMI Filtering
    2. 8.2 Typical Applications
      1. 8.2.1 2.0 (Stereo BTL) System
        1. 8.2.1.1 Design Requirements
        2. 8.2.1.2 Detailed Design Procedures
          1. 8.2.1.2.1 Step 1: Hardware Integration
          2. 8.2.1.2.2 Step 2: Speaker Tuning
          3. 8.2.1.2.3 Step 3: Software Integration
    3. 8.3 Power Supply Recommendations
      1. 8.3.1 DVDD Supply
      2. 8.3.2 PVDD Supply
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
        1. 8.4.1.1 General Guidelines for Audio Amplifiers
        2. 8.4.1.2 Importance of PVDD Bypass Capacitor Placement on PVDD Network
        3. 8.4.1.3 Optimizing Thermal Performance
          1. 8.4.1.3.1 Device, Copper, and Component Layout
          2. 8.4.1.3.2 Stencil Pattern
            1. 8.4.1.3.2.1 PCB footprint and Via Arrangement
            2. 8.4.1.3.2.2 Solder Stencil
      2. 8.4.2 Layout Example
  11. 9 Device and Documentation Support
    1. 9.1 Device Support
      1. 9.1.1 Device Nomenclature
    2. 9.2 Receiving Notification of Documentation Updates
    3. 9.3 Support Resources
    4. 9.4 Trademarks
    5. 9.5 Electrostatic Discharge Caution
    6. 9.6 Glossary
  12. 10Revision History
  13. 11Mechanical, Packaging, and Orderable Information
    1.     PACKAGE OPTION ADDENDUM
    2. 11.1 Tape and Reel Information
    3. 11.2 Mechanical Data

6.5.3.2 Shutdown Procedures

  1. The device is in normal operation.
  2. Configure the Register DEVICE_CTRL2 Regsiter [1:0]=00 (DEEP SLEEP) via the I2C control port or Pull PDN low.
  3. The clocks can now be stopped and the power supplies brought down.
  4. The device is now fully shutdown and powered off.
TAS5802 Power down sequence
A. Before PVDD/DVDD power down, Class D Output driver needs to be disabled by PDN or by I2C.
B. At least 6ms delay needed based on: LRCLK (Fs) = 48kHz, digital volume =24dB, digital volume ramp down by 0.5dB every sample period. Changing the value of DIG_VOL_CTRL2 or DIG_VOL_CTRL3 registers or changing the or change the LRCLK rate will change the delay time.
Figure 6-17 Power down sequence