SLLSFP9B February   2024  – October 2025 TCAN1575-Q1 , TCAN1576-Q1

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Comparison Table
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Supply Characteristics
    6. 6.6 Electrical Characteristics
    7. 6.7 Timing Requirements
    8. 6.8 Switching Characteristics
    9. 6.9 Typical Characteristics
  8. 7 Parameter Measurement Information
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  VSUP Pin
      2. 8.3.2  VIO Pin
      3. 8.3.3  VCC Pin
      4. 8.3.4  GND Pin
      5. 8.3.5  INH/LIMP Pin
      6. 8.3.6  WAKE Pin
      7. 8.3.7  TXD Pin
      8. 8.3.8  RXD Pin
      9. 8.3.9  SDO or nINT Interrupt Pin
      10. 8.3.10 nCS Pin
      11. 8.3.11 SCK
      12. 8.3.12 SDI
      13. 8.3.13 CANH and CANL Bus Pins
      14. 8.3.14 CAN FD SIC Transceiver
    4. 8.4 Device Functional Modes
      1. 8.4.1 Normal Mode
      2. 8.4.2 Standby Mode
      3. 8.4.3 Listen Only Mode
      4. 8.4.4 Sleep Mode
        1. 8.4.4.1 Bus Wake via RXD Request (BWRR) in Sleep Mode
        2. 8.4.4.2 Local Wake Up (LWU) via WAKE Input Terminal
      5. 8.4.5 Selective Wake-up
        1. 8.4.5.1 Selective Wake Mode
        2. 8.4.5.2 Frame Detection
        3. 8.4.5.3 Wake-Up Frame (WUF) Validation
        4. 8.4.5.4 WUF ID Validation
        5. 8.4.5.5 WUF DLC Validation
        6. 8.4.5.6 WUF Data Validation
        7. 8.4.5.7 Frame error counter
        8. 8.4.5.8 CAN FD Frame Tolerance
      6. 8.4.6 Fail-safe Features
        1. 8.4.6.1 Sleep Mode via Sleep Wake Error
        2. 8.4.6.2 Fail-safe Mode
      7. 8.4.7 Protection Features
        1. 8.4.7.1 Driver and Receiver Function
        2. 8.4.7.2 Floating Terminals
        3. 8.4.7.3 TXD Dominant Time Out (DTO)
        4. 8.4.7.4 CAN Bus Short Circuit Current Limiting
        5. 8.4.7.5 Thermal Shutdown
        6. 8.4.7.6 Under-Voltage Lockout (UVLO) and Unpowered Device
          1. 8.4.7.6.1 UVSUP, UVCC
          2. 8.4.7.6.2 UVIO
            1. 8.4.7.6.2.1 Fault Behavior
        7. 8.4.7.7 Watchdog (TCAN1576-Q1)
          1. 8.4.7.7.1 Watchdog Error Counter
          2. 8.4.7.7.2 Watchdog SPI Control Programming
            1. 8.4.7.7.2.1 Watchdog Configuration Registers Lock and Unlock
          3. 8.4.7.7.3 Watchdog Timing
          4. 8.4.7.7.4 Question and Answer Watchdog
            1. 8.4.7.7.4.1 WD Question and Answer Basic Information
            2. 8.4.7.7.4.2 Question and Answer Register and Settings
            3. 8.4.7.7.4.3 WD Question and Answer Value Generation
              1. 8.4.7.7.4.3.1 Answer Comparison
              2. 8.4.7.7.4.3.2 Sequence of the 2-bit Watchdog Answer Counter
            4. 8.4.7.7.4.4 Question and Answer WD Example
              1. 8.4.7.7.4.4.1 Example Configuration for Desired Behavior
              2. 8.4.7.7.4.4.2 Example of Performing a Question and Answer Sequence
      8. 8.4.8 Bus Fault Detection and Communication (TCAN1576-Q1)
    5. 8.5 Programming
      1. 8.5.1 SPI Communication
        1. 8.5.1.1 Chip Select Not (nCS):
        2. 8.5.1.2 SPI Clock Input (SCK):
        3. 8.5.1.3 SPI Serial Data Input (SDI):
        4. 8.5.1.4 SPI Serial Data Output (SDO):
  10. 9 Application Information Disclaimer
    1. 9.1 Application Information
      1. 9.1.1 Signal Improvement Capable (SIC)
      2. 9.1.2 CAN Termination
        1. 9.1.2.1 Termination
        2. 9.1.2.2 CAN Bus Biasing
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Brownout
      3. 9.2.3 Application Curves
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  11. 10Registers
    1. 10.1 Register Maps
      1. 10.1.1  DEVICE_ID_y Register (Address = 0h + formula) [reset = value]
      2. 10.1.2  REV_ID_MAJOR Register (Address = 8h) [reset = 00h]
      3. 10.1.3  REV_ID_MINOR Register (Address = 9h) [reset = 01h]
      4. 10.1.4  SPI_RSVD_x Register (Address = Ah + formula) [reset = 00h]
      5. 10.1.5  Scratch_Pad_SPI Register (Address = Fh) [reset = 00h]
      6. 10.1.6  MODE_CNTRL Register (Address = 10h) [reset = 04h]
      7. 10.1.7  WAKE_PIN_CONFIG Register (Address = 11h) [reset = 4h]
      8. 10.1.8  PIN_CONFIG Register (Address = 12h) [reset = 00h]
      9. 10.1.9  WD_CONFIG_1 Register (Address = 13h) [reset = 15h]
      10. 10.1.10 WD_CONFIG_2 Register (Address = 14h) [reset = 02h]
      11. 10.1.11 WD_INPUT_TRIG Register (Address = 15h) [reset = 00h]
      12. 10.1.12 WD_RST_PULSE Register (Address = 16h) [reset = 07h]
      13. 10.1.13 FSM_CONFIG Register (Address = 17h) [reset = 00h]
      14. 10.1.14 FSM_CNTR Register (Address = 18h) [reset = 00h]
      15. 10.1.15 DEVICE_RST Register (Address = 19h) [reset = 00h]
      16. 10.1.16 DEVICE_CONFIG1 Register (Address = 1Ah) [reset = 00h]
      17. 10.1.17 DEVICE_CONFIG2 Register (Address = 1Bh) [reset = 0h]
      18. 10.1.18 SWE_EN Register (Address 1Ch) [reset = 04h]
      19. 10.1.19 SDO_CONFIG Register (Address = 29h) [reset = 00h]
      20. 10.1.20 WD_QA_CONFIG Register (Address = 2Dh) [reset = 00h]
      21. 10.1.21 WD_QA_ANSWER Register (Address = 2Eh) [reset = 00h]
      22. 10.1.22 WD_QA_QUESTION Register (Address = 2Fh) [reset = 3Ch]
      23. 10.1.23 SW_ID1 Register (Address = 30h) [reset = 00h]
      24. 10.1.24 SW_ID2 Register (Address = 31h) [reset = 00h]
      25. 10.1.25 SW_ID3 Register (Address = 32h) [reset = 00h]
      26. 10.1.26 SW_ID4 Register (Address = 33h) [reset = 00h]
      27. 10.1.27 SW_ID_MASK1 Register (Address = 34h) [reset = 00h]
      28. 10.1.28 SW_ID_MASK2 Register (Address = 35h) [reset = 00h]
      29. 10.1.29 SW_ID_MASK3 Register (Address = 36h) [reset = 00h]
      30. 10.1.30 SW_ID_MASK4 Register (Address = 37h) [reset = 00h]
      31. 10.1.31 SW_ID_MASK_DLC Register (Address = 38h) [reset = 00h]
      32. 10.1.32 DATA_y Register (Address = 39h + formula) [reset = 00h]
      33. 10.1.33 SW_RSVD_y Register (Address = 41h + formula) [reset = 00h]
      34. 10.1.34 SW_CONFIG_1 Register (Address = 44h) [reset = 50h]
      35. 10.1.35 SW_CONFIG_2 Register (Address = 45h) [reset = 00h]
      36. 10.1.36 SW_CONFIG_3 Register (Address = 46h) [reset = 1Fh]
      37. 10.1.37 SW_CONFIG_4 Register (Address = 47h) [reset = 00h]
      38. 10.1.38 SW_CONFIG_RSVD_y Register (Address = 48h + formula) [reset = 00h]
      39. 10.1.39 DEVICE_CONFIGx Register (Address = 4Bh) [reset = 0h]
      40. 10.1.40 INT_GLOBAL Register (Address = 50h) [reset = 00h]
      41. 10.1.41 INT_1 Register (Address = 51h) [reset = 00h]
      42. 10.1.42 INT_2 Register (Address = 52h) [reset = 40h]
      43. 10.1.43 INT_3 Register (Address 53h) [reset = 00h]
      44. 10.1.44 INT_CANBUS Register (Address = 54h) [reset = 00h]
      45. 10.1.45 INT_GLOBAL_ENABLE (Address = 55h) [reset = 00h]
      46. 10.1.46 INT_ENABLE_1 Register (Address = 56h) [reset = FFh]
      47. 10.1.47 INT_ENABLE_2 Register (Address = 57h) [reset = 1Fh]
      48. 10.1.48 INT_ENABLE_3 Register (Address = 58h) [reset = 0h]
      49. 10.1.49 INT_ENABLE_CANBUS Register (Address = 59h) [reset = 7Fh]
      50. 10.1.50 INT_RSVD_y Register (Address = 5Ah + formula) [reset = 00h]
  12. 11Device and Documentation Support
    1. 11.1 Documentation Support
      1. 11.1.1 CAN Transceiver Physical Layer Standards:
      2. 11.1.2 EMC Requirements:
      3. 11.1.3 Conformance Test Requirements:
      4. 11.1.4 Related Documentation
    2. 11.2 Receiving Notification of Documentation Updates
    3. 11.3 Support Resources
    4. 11.4 Trademarks
    5. 11.5 Electrostatic Discharge Caution
    6. 11.6 Glossary
  13. 12Revision History
  14. 13Mechanical, Packaging, and Orderable Information

Timing Requirements

parameters valid across -40℃ ≤ TJ ≤ 150℃ (unless otherwise noted)
MIN NOM MAX UNIT
SUPPLY
tPWRUP Time from VSUP exceeding 4.4V until INH active; see Power Up Timing 2 4 ms
tUVFLTR Under voltage detection delay time 3 50 µs
tUVSLP Time from an UVCC and/or UVIO event to clear before transitioning to sleep or failsafe mode 200 400 ms
MODE CHANGE
tMODE_STBY_NOM The time it takes for the part to transition to normal mode from standby mode after receiving this command via SPI; see Section 7 70 µs
tMODE_NOM_SLP The time it takes for the part to transition to sleep mode from normal mode after receiving this command via SPI; see Normal to Sleep Timing 200 µs
tMODE_SLP_STBY Time from UVCC and UVIO clearing after INH turns on to RXD pin pulling low; (3) see Sleep to Standby Timing 100 µs
tMODE_NOM_STBY The time it takes for the part to transition to standby mode from normal mode after receiving this command via SPI; see Normal to Standby Timing 70 µs
tINH_SLP_STBY WUP, LWU or WUF event until INH asserted; see Sleep to Standby Timing 100 µs
tINH_NOM_SLP SPI write to go to sleep from normal mode and INH turns off; see Normal to Sleep Timing 50 µs
DEVICE TIMING
tWAKE Wake up time from a wake edge on WAKE; standby, selective wake or sleep mode; See Local Wake Up – Rising Edge  and Local Wake Up – Falling Edge 40 µs
tWAKE_INVALID WAKE pin pulses shorter than this will be filtered out; See Local Wake Up – Rising Edge  and Local Wake Up – Falling Edge 10 µs
tWK_TIMEOUT Bus wake-up timeout value; see Wake Up Pattern (WUP) and Bus Wake via RXD Request (BWRR) 0.5 2 ms
tWK_FILTER Bus time to meet filtered bus requirements for wake-up request; 4.75V ≤ VCC ≤ 5.25V; see Wake Up Pattern (WUP) and Bus Wake via RXD Request (BWRR) 0.5 0.95 µs
tWK_WIDTH_MIN(4) Minimum WAKE Pin pulse width Register (1) (2) 11h[3:2] = 00b; see WAKE Pin Pulse Behavior 10 ms
Minimum WAKE Pin pulse width Register (1) (2) 11h[3:2] = 01b; see WAKE Pin Pulse Behavior 20 ms
Minimum WAKE Pin pulse width Register (1) (2)  11h[3:2] = 10b; see WAKE Pin Pulse Behavior 40 ms
Minimum WAKE Pin pulse width  Register (1) (2)  11h[3:2] = 11b; see WAKE Pin Pulse Behavior 80 ms
tWK_WIDTH_INVALID Maximum WAKE Pin pulse width that is considered invalid (1) (2) Register 11h[3:2] = 00b; see WAKE Pin Pulse Behavior 5 ms
Maximum WAKE Pin pulse width that is considered invalid (1) (2) Register 11h[3:2] = 01b; see WAKE Pin Pulse Behavior 10 ms
Maximum WAKE Pin pulse width that is considered invalid (1) (2) Register 11h[3:2] = 10b; see WAKE Pin Pulse Behavior 20 ms
Maximum WAKE Pin pulse width that is considered invalid (1) (2) Register 11h[3:2] = 11b; see WAKE Pin Pulse Behavior 40 ms
tWK_WIDTH_MAX Maximum WAKE Pin pulse window (1) Register 11h[1:0] = 00b; see WAKE Pin Pulse Behavior 750 950 ms
Maximum WAKE Pin pulse window (1) Register 11h[1:0] = 01b; see WAKE Pin Pulse Behavior 1000 1250 ms
Maximum WAKE Pin pulse window (1) Register 11h[1:0] = 10b; see WAKE Pin Pulse Behavior 1500 1875 ms
Maximum WAKE Pin pulse window (1) Register 11h[1:0] = 11b; see WAKE Pin Pulse Behavior 2000 2500 ms
tSILENCE Timeout for bus inactivity. Timer is reset and restarted when bus changes from dominant to recessive or vice versa. 0.6 1.2 s
tINACTIVE Sleep Wake Error (SWE) timer 3.75 5 min
tBias Time from the start of a dominant-recessive-dominant sequence. Each phase 6 µs until Vsym ≥ 0.1; see Test Signal Definition for Bias Reaction Time Measurement 250 µs
tTXD_DTO Dominant time out, RL = 60Ω, CL = open;
see TXD Dominant Time Out Test Circuit and Measurement
1 5 ms
tTOGGLE RXD pin toggle timing when programmed after a WUP; see Wake Up Pattern (WUP) and Bus Wake via RXD Request (BWRR) 5 10 15 µs
This parameter is valid only when register 11h[7:6] = 11b
This is the minimum pulse width for a WAKE pin input that device will detect as a good pulse.  Values between the min tWK_WIDTH_MIN and max tWK_WIDTH_INVALID are indeterminate and may or may not be considered valid.  This parameter works with tWK_WIDTH_MIN to determine if a WAKE input pulse is valid
Dependent upon VCC and VIO being above UVCC and UVIO after INH turns on node power. 
tWK_WIDTH_INVALID sets this value by using register 11h[3:2]