SLUS900F December   2008  – August 2026 BQ32000

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
    1.     Pin Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings #GUID-4430518C-46E5-4467-8224-12E6F82A6B20/AMR001
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 I2C Timing Requirements
    7. 5.7 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 IRQ Function
      2. 6.3.2 VBACK Switchover
      3. 6.3.3 Trickle Charge
    4. 6.4 Device Functional Modes
    5. 6.5 Programming
      1. 6.5.1 I2C Serial Interface
  8. 7 Register Maps
    1. 7.1 I2C Read After Backup Mode
    2. 7.2 Normal Register Descriptions
      1. 7.2.1  SECONDS Register (address = 0x00) [reset = 0XXXXXXb]
      2. 7.2.2  MINUTES Register (address = 0x01) [reset = 1XXXXXXb]
      3. 7.2.3  CENT_HOURS Register (address = 0x02) [reset = XXXXXXXXb]
      4. 7.2.4  DAY Register (address = 0x03) [reset = 00000XXXb]
      5. 7.2.5  DATE Register (address = 0x04) [reset = 00XXXXXXb]
      6. 7.2.6  MONTH Register (address = 0x05) [reset = 000XXXXXb]
      7. 7.2.7  YEARS Register (address = 0x06) [reset = XXXXXXXXb]
      8. 7.2.8  CAL_CFG1 Register (address = 0x07) [reset = 10000000b]
      9. 7.2.9  TCH2 Register (address = 0x08) [reset = 10010000b]
      10. 7.2.10 CFG2 Register (address = 0x09) [reset = 10101010b]
    3. 7.3 Special Function Registers
      1. 7.3.1 SF KEY 1 Register (address = 0x20) [reset = 00000000b]
      2. 7.3.2 SF KEY 2 Register (address = 0x21) [reset = 00000000b]
      3. 7.3.3 SFR Register (address = 0x22) [reset = 00000000b]
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 Reading From a Register
        2. 8.2.2.2 Leap Year Compensation
        3. 8.2.2.3 Utilizing the Backup Supply
        4. 8.2.2.4 Calibration Example of Crystal Input
        5. 8.2.2.5 Calculating the Super Capacitor Values Example
      3. 8.2.3 Application Curves
    3.     Power Supply Recommendations
    4. 8.3 Layout
      1. 8.3.1 Layout Guidelines
      2. 8.3.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Device Support
    2. 9.2 Community Resources
    3. 9.3 Trademarks
  11. 10Revision History
  12.   Mechanical, Packaging, and Orderable Information

7.2.10 CFG2 Register (address = 0x09) [reset = 10101010b]

Description – Configuration 2

Figure 7-10 CFG2 Register
76543210BIT(S)
RSVDTCFERSVDTCHEName
r/wr/wr/wr/wRead/Write
10101010Initial
10UCUC1010Cycle
RSVDReserved. The RSVD bits is written as 0.
TCFETrickle charge FET bypass. The TCFE bit is used to enable the trickle charge FET. When TCFE is 0, the FET is off. When TCFE is 1, the FET is on.
0Open
1Closed
TCHETrickle charge enable. The TCHE bits determine if the trickle charger is active. If TCHE is 0x5, then the trickle charger is active, otherwise, the trickle charger is inactive.