SLVSJF0A October   2025  – July 2026 DRV7167

ADVANCE INFORMATION  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information_DRV7167A
    5. 5.5 Electrical Characteristics
  7. 6 Typical Characteristics
  8. 7 Parameter Measurement Information
    1. 7.1 Propagation Delay and Mismatch Measurement
    2. 7.2 Slew Rate Measurement
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  Control Inputs
        1. 8.3.1.1 EN/FLT Control
      2. 8.3.2  Dead Time Setting in Single PWM Mode
      3. 8.3.3  Start-up and UVLO
      4. 8.3.4  Synchronous Bootstrap
      5. 8.3.5  Level Shift
      6. 8.3.6  Zero Voltage Detection (ZVD) Reporting
      7. 8.3.7  Slew Rate Control
      8. 8.3.8  Fault Indication
      9. 8.3.9  Overcurrent Protection (OCP)
      10. 8.3.10 Over Temperature Detection (OTD)
    4. 8.4 Device Functional Modes
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Bootstrap Capacitor
        2. 9.2.2.2 GVDD Bypass Capacitor
        3. 9.2.2.3 Power Dissipation
      3. 9.2.3 Application Curves
        1. 9.2.3.1 Slew rate plots
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Examples
  11. 10Device and Documentation Support
    1. 10.1 Documentation Support
      1. 10.1.1 Related Documentation
    2. 10.2 Receiving Notification of Documentation Updates
    3. 10.3 Support Resources
    4. 10.4 Trademarks
    5. 10.5 Electrostatic Discharge Caution
    6. 10.6 Glossary
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information
    1. 12.1 Package Information
      1. 12.1.1 Mechanical Data

Control Inputs

DRV7167A supports IIM mode and single PWM Mode. In Independent Input Mode (IIM), the DRV7167A input pins are independently controlled with TTL input thresholds and support 3.3V and 5V logic levels. Table 8-1 describes the configuration for single PWM mode and IIM mode.

Table 8-1 Control Input Configuration
MODE CONFIGURATION
IIM Mode
  • Connect resistor on RDLF pin (pin 4) to AGND pin (pin 15).
  • ENIN/HI (pin 12) is the control input for high side gate drive and PWM/LI (Pin 13) is the control input for low side gate drive.
Single PWM Mode
  • Float RDLF pin (pin 4) to enable the Single PWM mode, to confirm float detection, verify that the RDLF pin has less than 10pF parasitic capacitance.
  • Keep ENIN/HI (pin 12) high to enable the gate drive for both high side and low side FET.
  • PWM/LI (pin 13) is the control input for PWM. Low side FET turns on, when PWM is high and high-side FET turns on when PWM FET is low.
DRV7167 IIM
                                                  ModeFigure 8-2 IIM Mode
DRV7167 Single PWM Mode Figure 8-3 Single PWM Mode

DRV7167A implements overlap protection functionality (interlock), to prevent a shoot-through condition if both HI and LI are asserted high. If both HI and LI are asserted, both the high-side and low-side GaN FETs are turned off.

When used in single PWM mode, the DRV7167A operates from a single PWM input, with the dead-times between low-to-high set by the external resistors on the pins DLH and high-to-low transitions set by external resistors on the DHL pins, as specified in Section 8.3.2.