Startseite Audio Audioverstärker Lautsprecherverstärker
Startseite
Audio
Audioverstärker
Lautsprecherverstärker

LM48512

AKTIV

2,7-W-Mono-Klasse D-Audioverstärker mit Analog-Eingang, integriertem Aufwärtswandler und EMI-Unterdr

Jetzt bestellen
Datenblatt

LM48512

AKTIV
Datenblatt Jetzt bestellen

Produktdetails

Audio input type Analog Input Architecture Class-D Boosted Speaker channels (max) Mono Rating Catalog Power stage supply (max) (V) 5.5 Power stage supply (min) (V) 2.3 Load (min) (Ω) 4 Output power (W) 2.7 SNR (dB) 97 THD + N at 1 kHz (%) 0.03 Iq (typ) (mA) 14.5 Control interface GPIO Closed/open loop Closed Analog supply (min) (V) 2.3 Analog supply voltage (max) (V) 5.5 PSRR (dB) 90 Operating temperature range (°C) -40 to 85
Audio input type Analog Input Architecture Class-D Boosted Speaker channels (max) Mono Rating Catalog Power stage supply (max) (V) 5.5 Power stage supply (min) (V) 2.3 Load (min) (Ω) 4 Output power (W) 2.7 SNR (dB) 97 THD + N at 1 kHz (%) 0.03 Iq (typ) (mA) 14.5 Control interface GPIO Closed/open loop Closed Analog supply (min) (V) 2.3 Analog supply voltage (max) (V) 5.5 PSRR (dB) 90 Operating temperature range (°C) -40 to 85
DSBGA (YZR) 16 5.0625 mm² 2.25 x 2.25

  • E 2 S System Reduces EMI while Preserving Audio Quality and Efficiency
  • Integrated Boost Converter
  • Supply Voltage Level Detection on Boost Converter
  • Low Power Shutdown Mode
  • "Click and Pop" suppression
    •

  • E 2 S System Reduces EMI while Preserving Audio Quality and Efficiency
  • Integrated Boost Converter
  • Supply Voltage Level Detection on Boost Converter
  • Low Power Shutdown Mode
  • "Click and Pop" suppression
    •

    Part of National’s PowerWise family or products, the LM48512 delivers 1.8W into 8Ω, while consuming 14.5mA of quiescent current. The LM48512 also features National’s Enhanced Emissions Suppression (E 2S) system, a patented, ultra low EMI PWM architecture that significantly reduces RF emissions while preserving audio quality and efficiency. LM48512 improves battery life, reduces external component count, board area consumption, system cost, and simplifies design.

    The LM48512 is designed to meet the demands of portable multimedia devices. The LM48512 features high efficiency compared to other boosted amplifiers and low EMI Class D amplifiers. The LM48512 is capable of driving an 8Ω speaker to 5.5V levels (1.8W) from a 3.6V supply while operating at 82% efficiency. Flexible power supply requirements allow operation from 2.3V to 5.5V. The E 2S system features a patented edge rate control (ERC) architecture that further reduces emissions by minimizing the high frequency component of the device output, while maintaining high quality audio reproduction (THD+N = 0.03%) and high efficiency. A low power shutdown mode reduces supply current consumption to 0.04μA.

    The LM48512 features a battery-saving automatic gain control (AGC). The AGC detects the battery voltage and reduces the gain of the amplifier to limit the output as the battery voltage decreases.

    Superior click and pop suppression eliminates audible transients on power-up/down and during shutdown.

    Key Specifications

    ■  Power Output at VDD = 3.6V   RL = 8Ω, THD+N ≤ 1% 1.8W (typ)
    ■   Efficiency at 3.6V, 800mW into 8Ω 82% (typ)
    ■  Quiescent Power Supply Current   at 3.6V 14.5mA
    ■  Shutdown current 0.04μA (typ)

    Part of National’s PowerWise family or products, the LM48512 delivers 1.8W into 8Ω, while consuming 14.5mA of quiescent current. The LM48512 also features National’s Enhanced Emissions Suppression (E 2S) system, a patented, ultra low EMI PWM architecture that significantly reduces RF emissions while preserving audio quality and efficiency. LM48512 improves battery life, reduces external component count, board area consumption, system cost, and simplifies design.

    The LM48512 is designed to meet the demands of portable multimedia devices. The LM48512 features high efficiency compared to other boosted amplifiers and low EMI Class D amplifiers. The LM48512 is capable of driving an 8Ω speaker to 5.5V levels (1.8W) from a 3.6V supply while operating at 82% efficiency. Flexible power supply requirements allow operation from 2.3V to 5.5V. The E 2S system features a patented edge rate control (ERC) architecture that further reduces emissions by minimizing the high frequency component of the device output, while maintaining high quality audio reproduction (THD+N = 0.03%) and high efficiency. A low power shutdown mode reduces supply current consumption to 0.04μA.

    The LM48512 features a battery-saving automatic gain control (AGC). The AGC detects the battery voltage and reduces the gain of the amplifier to limit the output as the battery voltage decreases.

    Superior click and pop suppression eliminates audible transients on power-up/down and during shutdown.

    Key Specifications

    ■  Power Output at VDD = 3.6V   RL = 8Ω, THD+N ≤ 1% 1.8W (typ)
    ■   Efficiency at 3.6V, 800mW into 8Ω 82% (typ)
    ■  Quiescent Power Supply Current   at 3.6V 14.5mA
    ■  Shutdown current 0.04μA (typ)

    filter Andere Lautsprecherverstärker suchen
    Herunterladen Video mit Transkript ansehen Video

    Technische Dokumentation

    star =Von TI ausgewählte Top-Empfehlungen für dieses Produkt
    Keine Ergebnisse gefunden. Bitte geben Sie einen anderen Begriff ein und versuchen Sie es erneut.
    Alle anzeigen 4
    Typ Titel Datum
    * Data sheet PowerWise Boosted, Ultra Lo-EMI, Mono, E2S Class D Audio Pwr Amp datasheet (Rev. A) 09 Apr 2012
    Application note Guidelines for Measuring Audio Power Amplifier Performance (Rev. A) 26 Aug 2019
    Application note AN-1849 An Audio Amplifier Power Supply Design (Rev. C) 27 Jun 2019
    Application note AN-1737 Managing EMI in Class D Audio Applications (Rev. A) 01 Mai 2013

    Design und Entwicklung

    Weitere Bedingungen oder erforderliche Ressourcen enthält gegebenenfalls die Detailseite, die Sie durch Klicken auf einen der unten stehenden Titel erreichen.

    Simulationstool

    PSPICE-FOR-TI — PSpice® für TI Design-und Simulationstool

    PSpice® für TI ist eine Design- und Simulationsumgebung, welche Sie dabei unterstützt, die Funktionalität analoger Schaltungen zu evaluieren. Diese voll ausgestattete Design- und Simulationssuite verwendet eine analoge Analyse-Engine von Cadence®. PSpice für TI ist kostenlos erhältlich und (...)
    Anfordern
    Gehäuse Pins CAD-Symbole, Footprints und 3D-Modelle
    DSBGA (YZR) 16 Ultra Librarian
    Es gelten die allgemeinen Geschäftsbedingungen von TI für Evaluierungsartikel.

    Bestellen & Qualität

    Beinhaltete Information:
    • RoHS
    • REACH
    • Bausteinkennzeichnung
    • Blei-Finish/Ball-Material
    • MSL-Rating / Spitzenrückfluss
    • MTBF-/FIT-Schätzungen
    • Materialinhalt
    • Qualifikationszusammenfassung
    • Kontinuierliches Zuverlässigkeitsmonitoring
    Beinhaltete Information:
    • Werksstandort
    • Montagestandort

    Support und Schulungen

    TI E2E™-Foren mit technischem Support von TI-Ingenieuren

    Alle Forenthemen auf Englisch anzeigen

    Inhalte werden ohne Gewähr von TI und der Community bereitgestellt. Sie stellen keine Spezifikationen von TI dar. Siehe Nutzungsbedingungen.

    Bei Fragen zu den Themen Qualität, Gehäuse oder Bestellung von TI-Produkten siehe TI-Support. ​​​​​​​​​​​​​​

    Videos