Home Energiemanagement DC/DC-Spannungsversorgungsmodul Stromversorgungsmodule (integrierter Induktor)
NEU

TPSM846C26

AKTIV

Produktdetails

Rating Catalog Topology Buck Iout (max) (A) 35 Vin (max) (V) 18 Vin (min) (V) 2.7 Vout (max) (V) 5.5 Vout (min) (V) 0.4 Features Adjustable current limit, Differential Remote Sense, Enable, Extended security, Forced PWM, Overcurrent protection, PMBus, Phase Interleaving, Power good, Prebias startup, Soft-start adjustable, Stackable, Synchronous rectification, Telemetry, UVLO adjustable, Voltage Margining Operating temperature range (°C) -40 to 125 Type Module Duty cycle (max) (%) 85 Control mode D-CAP4 Switching frequency (min) (kHz) 400 Switching frequency (max) (kHz) 2000
Rating Catalog Topology Buck Iout (max) (A) 35 Vin (max) (V) 18 Vin (min) (V) 2.7 Vout (max) (V) 5.5 Vout (min) (V) 0.4 Features Adjustable current limit, Differential Remote Sense, Enable, Extended security, Forced PWM, Overcurrent protection, PMBus, Phase Interleaving, Power good, Prebias startup, Soft-start adjustable, Stackable, Synchronous rectification, Telemetry, UVLO adjustable, Voltage Margining Operating temperature range (°C) -40 to 125 Type Module Duty cycle (max) (%) 85 Control mode D-CAP4 Switching frequency (min) (kHz) 400 Switching frequency (max) (kHz) 2000
FCCSP (APQ) 99 65.625 mm² (7.5 mm × 8.75 mm)
  • Small form factor 7.5mm × 8.75mm BGA package
  • 3.975mm maximum height
  • 2.7V to 18V input voltage with external bias
  • 4V to 18V input voltage without external bias
  • 0.4V to 5.5V output voltage
  • Supports 35A single-phase or 2 ×, 3 ×, or 4 × stacked configurations
  • Rdson_HS = 2.6mΩ, Rdson_LS = 1mΩ
  • 400kHz to 2MHz operating frequency (four discrete settings through pin-strap, additional settings through PMBus®)
  • PMBus programmable
    • Revision 1.5 compliant with PASSKEY security feature
    • Input voltage, output voltage, output current, temperature telemetry
    • Programmable overcurrent, overvoltage, undervoltage, overtemperature protections
    • Includes single command write function in stacked configuration
    • Extended write protection feature
    • Non-volatile memory to store configuration settings
  • Two methods for programming the output voltage
    • Internal resistor divider (discrete settings) with boot-up voltage selected by pin-strapping
    • External resistor divider (continuous settings) with boot-up voltage selected by VBOOT
  • Precision voltage reference and differential remote sense for high output accuracy
    • ± 0.5% DAC accuracy from 0°C to 85°C junction
    • ± 0.85% VOUT tolerance from –40°C to 125°C junction
  • Selectable FCCM/DCM in single phase only
  • Start-up without PMBus communication through pin-strapping
  • Safe start-up into prebiased output
  • 0.5ms to 16ms programmable soft-start time
  • D-CAP4 control topology with fast transient response, supporting all ceramic output capacitors
  • Programmable internal loop compensation
  • Selectable cycle-by-cycle valley current limit
  • Open-drain power-good output
  • Small form factor 7.5mm × 8.75mm BGA package
  • 3.975mm maximum height
  • 2.7V to 18V input voltage with external bias
  • 4V to 18V input voltage without external bias
  • 0.4V to 5.5V output voltage
  • Supports 35A single-phase or 2 ×, 3 ×, or 4 × stacked configurations
  • Rdson_HS = 2.6mΩ, Rdson_LS = 1mΩ
  • 400kHz to 2MHz operating frequency (four discrete settings through pin-strap, additional settings through PMBus®)
  • PMBus programmable
    • Revision 1.5 compliant with PASSKEY security feature
    • Input voltage, output voltage, output current, temperature telemetry
    • Programmable overcurrent, overvoltage, undervoltage, overtemperature protections
    • Includes single command write function in stacked configuration
    • Extended write protection feature
    • Non-volatile memory to store configuration settings
  • Two methods for programming the output voltage
    • Internal resistor divider (discrete settings) with boot-up voltage selected by pin-strapping
    • External resistor divider (continuous settings) with boot-up voltage selected by VBOOT
  • Precision voltage reference and differential remote sense for high output accuracy
    • ± 0.5% DAC accuracy from 0°C to 85°C junction
    • ± 0.85% VOUT tolerance from –40°C to 125°C junction
  • Selectable FCCM/DCM in single phase only
  • Start-up without PMBus communication through pin-strapping
  • Safe start-up into prebiased output
  • 0.5ms to 16ms programmable soft-start time
  • D-CAP4 control topology with fast transient response, supporting all ceramic output capacitors
  • Programmable internal loop compensation
  • Selectable cycle-by-cycle valley current limit
  • Open-drain power-good output

The TPSM846C26 device is a highly-integrated buck module with D-CAP4 control topology for fast transient response. All programmable parameters can be configured by the PMBus interface and stored in NVM as the new default values to minimize the external component count. Pin-strap options allow for configuration as primary or secondary, stack position and stack number, DCM (single phase only) or FCCM, overcurrent limit, fault response, internal or external feedback resistor, output voltage selection or range, switching frequency, and compensation.

The PMBus interface with 1MHz clock support gives a convenient, standardized, digital interface for configuration as well as telemetry of key parameters including output voltage, output current, and internal die temperature. Response to fault conditions can be set to restart, latch off, or ignore, depending on system requirements. Two, three, and four TPSM846C26 devices can be interconnected to provide up to 140A on a single output.

The TPSM846C26 has an option to overdrive the internal 4.5V LDO with an external 5V supply through the VDRV pin to improve efficiency, reduce power dissipation, and enable start-up with a lower input voltage.

The TPSM846C26 is a lead-free device and is RoHS compliant without exemption.

The TPSM846C26 device is a highly-integrated buck module with D-CAP4 control topology for fast transient response. All programmable parameters can be configured by the PMBus interface and stored in NVM as the new default values to minimize the external component count. Pin-strap options allow for configuration as primary or secondary, stack position and stack number, DCM (single phase only) or FCCM, overcurrent limit, fault response, internal or external feedback resistor, output voltage selection or range, switching frequency, and compensation.

The PMBus interface with 1MHz clock support gives a convenient, standardized, digital interface for configuration as well as telemetry of key parameters including output voltage, output current, and internal die temperature. Response to fault conditions can be set to restart, latch off, or ignore, depending on system requirements. Two, three, and four TPSM846C26 devices can be interconnected to provide up to 140A on a single output.

The TPSM846C26 has an option to overdrive the internal 4.5V LDO with an external 5V supply through the VDRV pin to improve efficiency, reduce power dissipation, and enable start-up with a lower input voltage.

The TPSM846C26 is a lead-free device and is RoHS compliant without exemption.

Herunterladen Video mit Transkript ansehen Video

Technische Dokumentation

Keine Ergebnisse gefunden. Bitte geben Sie einen anderen Begriff ein und versuchen Sie es erneut.
Alle anzeigen 4
Top-Dokumentation Typ Titel Format-Optionen Neueste englische Version herunterladen Datum
* Datenblatt TPSM846C26 4V to 18V Input, 35A, 4 × Stackable, Synchronous Buck Module With PMBus and Telemetry datasheet PDF | HTML 13.10.2026
Application brief Higher Power Density With 35A TPSM846C26 Power Module Compared to 35A TPS546C25 DC/DC Converter and Inductor PDF | HTML 06.11.2026
Application brief Powering FPGAs Supporting SmartVID using TI Switching Regulators and Modules With PMBus PDF | HTML 21.07.2026
EVM User's guide TPSM846C26 SWIFT™ Step-Down Converter Evaluation Module PDF | HTML 23.06.2026

Design und Entwicklung

Weitere Bedingungen oder erforderliche Ressourcen enthält gegebenenfalls die Detailseite, die Sie durch Klicken auf einen der unten stehenden Titel erreichen.

Evaluierungsplatine

TPSM846C26EVM-2PH — TPSM846C26 Zweiphasen-Evaluierungsmodul für Abwärtswandler

TPSM846C26EVM-2PH ist ein einphasiges Abwärts-Leistungsmodul unter Verwendung des Bausteins TPSM846C26. Das TPSM846C26EVM-2PH ist für einen nominalen 12 V-Bus ausgelegt und erzeugt einen geregelten 0,8 V-Ausgang bei bis zu 35 A-Laststrom.
Benutzerhandbuch: PDF | HTML
Unterstützte Produkte und Hardware
Designtool

PMBUS-DESIGN-TOOL — Support PMBus Interface for Buck Converters and Modules

Digital Fusion support for PMBus converters and modules. USB-TO-GPIO2 adapter is needed.
Unterstützte Produkte und Hardware
Gehäuse Pins CAD-Symbole, Footprints und 3D-Modelle
FCCSP (APQ) 99 Ultra Librarian

Bestellen & Qualität

Support und Schulungen

TI E2E™-Foren mit technischem Support von TI-Ingenieuren

Inhalte werden ohne Gewähr von TI und der Community bereitgestellt. Sie stellen keine Spezifikationen von TI dar. Siehe Nutzungsbedingungen.

Bei Fragen zu den Themen Qualität, Gehäuse oder Bestellung von TI-Produkten siehe TI-Support. ​​​​​​​​​​​​​​

Videos