Inicio Gestión de la energía Convertidores de CA/CC y CC/CC (FET integrado)
Inicio
Gestión de la energía
Convertidores de CA/CC y CC/CC (FET integrado)
NUEVO

LMR43606-Q1

ACTIVO

Convertidor reductor síncrono de 36V V y 600mA A con IQ de 4uA uA y alta eficiencia de carga

Haga su pedido ahora
Hoja de datos

LMR43606-Q1

ACTIVO
Hoja de datos Haga su pedido ahora

Detalles del producto

Rating Automotive Operating temperature range (°C) -40 to 125 TI functional safety category Functional Safety-Capable Topology Buck Type Converter Iout (max) (A) 0.6 Vin (min) (V) 3 Vin (max) (V) 36 Switching frequency (min) (kHz) 200 Switching frequency (max) (kHz) 2200 Features Enable, Fixed Output, Forced PWM, Frequency synchronization, Light Load Efficiency, Over Current Protection, Power good, Pre-Bias Start-Up, Soft Start Fixed, Spread Spectrum, Synchronous Rectification, UVLO Fixed, Wettable flanks package Control mode current mode Vout (min) (V) 1 Vout (max) (V) 32 Iq (typ) (A) 0.0000015
Rating Automotive Operating temperature range (°C) -40 to 125 TI functional safety category Functional Safety-Capable Topology Buck Type Converter Iout (max) (A) 0.6 Vin (min) (V) 3 Vin (max) (V) 36 Switching frequency (min) (kHz) 200 Switching frequency (max) (kHz) 2200 Features Enable, Fixed Output, Forced PWM, Frequency synchronization, Light Load Efficiency, Over Current Protection, Power good, Pre-Bias Start-Up, Soft Start Fixed, Spread Spectrum, Synchronous Rectification, UVLO Fixed, Wettable flanks package Control mode current mode Vout (min) (V) 1 Vout (max) (V) 32 Iq (typ) (A) 0.0000015
VQFN-HR (RPE) 9 4 mm² 2 x 2
  • AEC-Q100-qualified for automotive applications:
    • Temperature grade 1: –40°C to +125°C, TA
  • Functional Safety-Capable
  • Greater than 85% efficiency at 1mA
  • Miniature design size and low component cost
    • 2mm × 2mm HotRod™ package with wettable flanks
    • Internal compensation
  • Designed for ultra-low EMI requirements
    • Spread spectrum reduces peak emissions
    • Pin selectable FPWM mode for constant frequency at light loads with MODE/SYNC pin
    • FSW synchronization with MODE/SYNC pin
  • Designed for automotive applications
    • –40°C to +150°C junction temperature range
    • Supports 42V automotive load dump
    • Supports 3-VIN for automotive cold crank
    • Adjustable up to 95% of VIN, 3.3V and 5V fixed VOUT options available
  • Designed for scalable power supplies
  • AEC-Q100-qualified for automotive applications:
    • Temperature grade 1: –40°C to +125°C, TA
  • Functional Safety-Capable
  • Greater than 85% efficiency at 1mA
  • Miniature design size and low component cost
    • 2mm × 2mm HotRod™ package with wettable flanks
    • Internal compensation
  • Designed for ultra-low EMI requirements
    • Spread spectrum reduces peak emissions
    • Pin selectable FPWM mode for constant frequency at light loads with MODE/SYNC pin
    • FSW synchronization with MODE/SYNC pin
  • Designed for automotive applications
    • –40°C to +150°C junction temperature range
    • Supports 42V automotive load dump
    • Supports 3-VIN for automotive cold crank
    • Adjustable up to 95% of VIN, 3.3V and 5V fixed VOUT options available
  • Designed for scalable power supplies

The LMR43606-Q1 is a small, 36V, 0.6A, synchronous step-down DC/DC converter in a 2mm × 2mm HotRod package. This easy-to-use converter supports a wide input voltage range of 3.0V to 36V with transients up to 42V.

The LMR43606-Q1 is specifically designed to meet low standby power requirements for always on, automotive applications. Auto mode enables frequency foldback when operating at light loads, allowing an unloaded current consumption of 1.5µA at 13.5VIN and high light load efficiency. A seamless transition between PWM and PFM modes along with very low MOSFET ON resistances provide exceptional efficiency across the entire load range.

The control architecture and feature-set are designed for an ultra-small design size. The device uses peak current mode control to minimize output capacitance. The LMR43606-Q1 minimizes input filter size by using dual random spread spectrum, a low-EMI HotRod package, and an optimized pinout. The MODE/SYNC and RT pin variants can be used to set or synchronize the frequency between 200kHz and 2.2MHz to avoid noise sensitive frequency bands.

The rich feature set of the LMR43606-Q1 is designed to simplify implementation for a wide range of automotive end equipments.

The LMR43606-Q1 is a small, 36V, 0.6A, synchronous step-down DC/DC converter in a 2mm × 2mm HotRod package. This easy-to-use converter supports a wide input voltage range of 3.0V to 36V with transients up to 42V.

The LMR43606-Q1 is specifically designed to meet low standby power requirements for always on, automotive applications. Auto mode enables frequency foldback when operating at light loads, allowing an unloaded current consumption of 1.5µA at 13.5VIN and high light load efficiency. A seamless transition between PWM and PFM modes along with very low MOSFET ON resistances provide exceptional efficiency across the entire load range.

The control architecture and feature-set are designed for an ultra-small design size. The device uses peak current mode control to minimize output capacitance. The LMR43606-Q1 minimizes input filter size by using dual random spread spectrum, a low-EMI HotRod package, and an optimized pinout. The MODE/SYNC and RT pin variants can be used to set or synchronize the frequency between 200kHz and 2.2MHz to avoid noise sensitive frequency bands.

The rich feature set of the LMR43606-Q1 is designed to simplify implementation for a wide range of automotive end equipments.
filter Buscar otro/a Convertidores de CA/CC y CC/CC (FET integrado)
Descargar Ver vídeo con transcripción Video

Documentación técnica

star =Principal documentación para este producto seleccionada por TI
No se encontraron resultados. Borre su búsqueda y vuelva a intentarlo.
Ver todo 4
Tipo Título Fecha
* Data sheet LMR43606-Q1, 36V, 0.6A, Automotive Buck Converter With < 2.5µA IQ at 150°C TJMAX in 4mm2 HotRod™ QFN datasheet PDF | HTML 12 ene 2024
EVM User's guide LMR43606-Q1 Evaluation Module User's Guide PDF | HTML 18 mar 2024
Certificate LMR43606MQ3EVM-2M EU Declaration of Conformity (DoC) 06 mar 2024
Functional safety information LMR43606-Q1 Functional Safety, FIT Rate, Failure Mode Distribution and Pin FMA PDF | HTML 16 ene 2024

Diseño y desarrollo

Para conocer los términos adicionales o los recursos necesarios, haga clic en cualquier título de abajo para ver la página de detalles cuando esté disponible.

Placa de evaluación

LMR43606MQ3EVM-2M — LMR43606-Q1 evaluation module

The LMR43606-Q1 is an easy-to-use, synchronous, step-down voltage converter. The LMR43606MQ3EVM-2M is a fully assembled and tested circuit for evaluating the LMR43606-Q1 converter. This EVM is designed to be operated with a 3.5V to 36V input and provides a 3.3V output with a load up to 600mA.

Guía del usuario: PDF | HTML
No disponible en TI.com
Placa de evaluación

LMR43620MQ3EVM-2M — Módulo de evaluación del convertidor reductor síncrono LMR43620-Q1 de 36 V de entrada, 3.3 V de sali

El módulo de evaluación (EVM) LMR43620MQ3EVM-2M ayuda a los diseñadores a evaluar el funcionamiento y el rendimiento del regulador reductor de entrada amplia LMR43620-Q1. El LMR43620-Q1 es un convertidor reductor CC-CC síncrono fácil de usar que puede manejar hasta 2 A de corriente de carga con una (...)

Guía del usuario: PDF | HTML
No disponible en TI.com
Placa de evaluación

LMR43620RQ5EVM-400 — Módulo de evaluación del convertidor reductor síncrono LMR43620-Q1 de 36 V de entrada, 5 V de salida

El módulo de evaluación (EVM) LMR43620RQ5EVM-400 ayuda a evaluar el funcionamiento y el rendimiento del regulador reductor de entrada ancha LMR43620-Q1. El LMR43620-Q1 es un convertidor reductor CC-CC síncrono fácil de usar que puede manejar hasta 2 A de corriente de carga con una tensión de (...)

Guía del usuario: PDF | HTML
No disponible en TI.com
Paquete Pasadores Descargar
VQFN-HR (RPE) 9 Ver opciones
Se aplican los Términos y condiciones estándar de TI para los elementos de evaluación.

Pedidos y calidad

Información incluida:
  • RoHS
  • REACH
  • Marcado del dispositivo
  • Acabado de plomo/material de la bola
  • Clasificación de nivel de sensibilidad a la humedad (MSL) / reflujo máximo
  • Estimaciones de tiempo medio entre fallas (MTBF)/fallas en el tiempo (FIT)
  • Contenido del material
  • Resumen de calificaciones
  • Monitoreo continuo de confiabilidad
Información incluida:
  • Lugar de fabricación
  • Lugar de ensamblaje

Soporte y capacitación

Foros de TI E2E™ con asistencia técnica de los ingenieros de TI

Ver todos los temas del foro en inglés

El contenido lo proporcionan “tal como está” TI y los colaboradores de la comunidad y no constituye especificaciones de TI. Consulte los términos de uso.

Si tiene preguntas sobre la calidad, el paquete o el pedido de productos de TI, consulte el soporte de TI. ​​​​​​​​​​​​​​

Videos