이 제품의 최신 버전이 있습니다

open-in-new 대안 비교
다른 핀 출력을 지원하지만 비교 대상 장치와 동일한 기능
CC2651R3 활성 352kB 플래시가 포함된 SimpleLink™ 32비트 Arm® Cortex®-M4F 단일 프로토콜 2.4GHz 무선 MCU Higher performance option with upgraded core

제품 상세 정보

CPU core 8051 Technology Zigbee Protocols Zigbee 2.6 Flash memory (kByte) 256 RAM (kByte) 8 Peripherals 12-bit ADC 8-channel, 2SPI/ UART, 4 timers Number of GPIOs 21 Security Cryptographic acceleration, Device attestation & anti-counterfeit Operating system TI RTOS Type Wireless MCU Sensitivity (best) (dBm) -97 Operating temperature range (°C) -40 to 125 Cryptographic accelerators AES Edge AI enabled No
CPU core 8051 Technology Zigbee Protocols Zigbee 2.6 Flash memory (kByte) 256 RAM (kByte) 8 Peripherals 12-bit ADC 8-channel, 2SPI/ UART, 4 timers Number of GPIOs 21 Security Cryptographic acceleration, Device attestation & anti-counterfeit Operating system TI RTOS Type Wireless MCU Sensitivity (best) (dBm) -97 Operating temperature range (°C) -40 to 125 Cryptographic accelerators AES Edge AI enabled No
VQFN (RHA) 40 36 mm² 6 x 6
  • RF/Layout
    • 2.4-GHz IEEE 802.15.4 Compliant RF Transceiver
    • Excellent Receiver Sensitivity and Robustness to Interference
    • Programmable Output Power Up to 4.5 dBm
    • Very Few External Components
    • Only a Single Crystal Needed for Asynchronous Networks
    • 6-mm × 6-mm QFN40 Package
    • Suitable for Systems Targeting Compliance With Worldwide Radio-
      Frequency Regulations: ETSI EN 300 328 and EN 300 440 (Europe),
      FCC CFR47 Part 15 (US) and ARIB STD-T-66 (Japan)
  • Low Power
    • Active-Mode RX (CPU Idle): 24 mA
    • Active Mode TX at 1 dBm (CPU Idle): 29 mA
    • Power Mode 1 (4 µs Wake-Up): 0.2 mA
    • Power Mode 2 (Sleep Timer Running): 1 µA
    • Power Mode 3 (External Interrupts): 0.4 µA
    • Wide Supply-Voltage Range (2 V–3.6 V)
  • Microcontroller
    • High-Performance and Low-Power 8051 Microcontroller Core
      With Code Prefetch
    • 32-, 64-, 128-, or 256-KB In-System-Programmable Flash
    • 8-KB RAM With Retention in All Power Modes
    • Hardware Debug Support
  • Peripherals
    • Powerful Five-Channel DMA
    • Integrated High-Performance Op-Amp and Ultralow-Power Comparator
    • IEEE 802.15.4 MAC Timer, General-Purpose Timers
      (One 16-Bit, Two 8-Bit)
    • IR Generation Circuitry
    • 32-kHz Sleep Timer With Capture
    • CSMA/CA Hardware Support
    • Accurate Digital RSSI/LQI Support
    • Battery Monitor and Temperature Sensor
    • 12-Bit ADC With Eight Channels and Configurable Resolution
    • AES Security Coprocessor
    • Two Powerful USARTs With Support for Several Serial Protocols
    • 21 General-Purpose I/O Pins
      (19 × 4 mA, 2 × 20 mA)
    • Watchdog Timer
  • Development Tools
    • CC2530 Development Kit
    • CC2530 ZigBee Development Kit
    • CC2530 RemoTI Development Kit for RF4CE
    • SmartRF Software
    • Packet Sniffer
    • IAR Embedded Workbench Available
  • APPLICATIONS
    • 2.4-GHz IEEE 802.15.4 Systems
    • RF4CE Remote Control Systems (64-KB Flash and Higher)
    • ZigBee Systems (256-KB Flash)
    • Home/Building Automation
    • Lighting Systems
    • Industrial Control and Monitoring
    • Low-Power Wireless Sensor Networks
    • Consumer Electronics
    • Health Care

RemoTI, SmartRF, Z-Stack are trademarks of Texas Instruments.
IAR Embedded Workbench is a trademark of IAR Systems AB.
ZigBee is a registered trademark of the ZigBee Alliance.
All other trademarks are the property of their respective owners.

  • RF/Layout
    • 2.4-GHz IEEE 802.15.4 Compliant RF Transceiver
    • Excellent Receiver Sensitivity and Robustness to Interference
    • Programmable Output Power Up to 4.5 dBm
    • Very Few External Components
    • Only a Single Crystal Needed for Asynchronous Networks
    • 6-mm × 6-mm QFN40 Package
    • Suitable for Systems Targeting Compliance With Worldwide Radio-
      Frequency Regulations: ETSI EN 300 328 and EN 300 440 (Europe),
      FCC CFR47 Part 15 (US) and ARIB STD-T-66 (Japan)
  • Low Power
    • Active-Mode RX (CPU Idle): 24 mA
    • Active Mode TX at 1 dBm (CPU Idle): 29 mA
    • Power Mode 1 (4 µs Wake-Up): 0.2 mA
    • Power Mode 2 (Sleep Timer Running): 1 µA
    • Power Mode 3 (External Interrupts): 0.4 µA
    • Wide Supply-Voltage Range (2 V–3.6 V)
  • Microcontroller
    • High-Performance and Low-Power 8051 Microcontroller Core
      With Code Prefetch
    • 32-, 64-, 128-, or 256-KB In-System-Programmable Flash
    • 8-KB RAM With Retention in All Power Modes
    • Hardware Debug Support
  • Peripherals
    • Powerful Five-Channel DMA
    • Integrated High-Performance Op-Amp and Ultralow-Power Comparator
    • IEEE 802.15.4 MAC Timer, General-Purpose Timers
      (One 16-Bit, Two 8-Bit)
    • IR Generation Circuitry
    • 32-kHz Sleep Timer With Capture
    • CSMA/CA Hardware Support
    • Accurate Digital RSSI/LQI Support
    • Battery Monitor and Temperature Sensor
    • 12-Bit ADC With Eight Channels and Configurable Resolution
    • AES Security Coprocessor
    • Two Powerful USARTs With Support for Several Serial Protocols
    • 21 General-Purpose I/O Pins
      (19 × 4 mA, 2 × 20 mA)
    • Watchdog Timer
  • Development Tools
    • CC2530 Development Kit
    • CC2530 ZigBee Development Kit
    • CC2530 RemoTI Development Kit for RF4CE
    • SmartRF Software
    • Packet Sniffer
    • IAR Embedded Workbench Available
  • APPLICATIONS
    • 2.4-GHz IEEE 802.15.4 Systems
    • RF4CE Remote Control Systems (64-KB Flash and Higher)
    • ZigBee Systems (256-KB Flash)
    • Home/Building Automation
    • Lighting Systems
    • Industrial Control and Monitoring
    • Low-Power Wireless Sensor Networks
    • Consumer Electronics
    • Health Care

RemoTI, SmartRF, Z-Stack are trademarks of Texas Instruments.
IAR Embedded Workbench is a trademark of IAR Systems AB.
ZigBee is a registered trademark of the ZigBee Alliance.
All other trademarks are the property of their respective owners.

The CC2530 is a true system-on-chip (SoC) solution for IEEE 802.15.4, Zigbee and RF4CE applications. It enables robust network nodes to be built with very low total bill-of-material costs. The CC2530 combines the excellent performance of a leading RF transceiver with an industry-standard enhanced 8051 MCU, in-system programmable flash memory, 8-KB RAM, and many other powerful features. The CC2530 comes in four different flash versions: CC2530F32/64/128/256, with 32/64/128/256 KB of flash memory, respectively. The CC2530 has various operating modes, making it highly suited for systems where ultralow power consumption is required. Short transition times between operating modes further ensure low energy consumption.

Combined with the industry-leading and golden-unit-status ZigBee protocol stack (Z-Stack) from Texas Instruments, the CC2530F256 provides a robust and complete ZigBee solution.

Combined with the golden-unit-status RemoTI stack from Texas Instruments, the CC2530F64 and higher provide a robust and complete ZigBee RF4CE remote-control solution.

The CC2530 is a true system-on-chip (SoC) solution for IEEE 802.15.4, Zigbee and RF4CE applications. It enables robust network nodes to be built with very low total bill-of-material costs. The CC2530 combines the excellent performance of a leading RF transceiver with an industry-standard enhanced 8051 MCU, in-system programmable flash memory, 8-KB RAM, and many other powerful features. The CC2530 comes in four different flash versions: CC2530F32/64/128/256, with 32/64/128/256 KB of flash memory, respectively. The CC2530 has various operating modes, making it highly suited for systems where ultralow power consumption is required. Short transition times between operating modes further ensure low energy consumption.

Combined with the industry-leading and golden-unit-status ZigBee protocol stack (Z-Stack) from Texas Instruments, the CC2530F256 provides a robust and complete ZigBee solution.

Combined with the golden-unit-status RemoTI stack from Texas Instruments, the CC2530F64 and higher provide a robust and complete ZigBee RF4CE remote-control solution.

다운로드 스크립트와 함께 비디오 보기 비디오

기술 자료

star =TI에서 선정한 이 제품의 인기 문서
검색된 결과가 없습니다. 검색어를 지우고 다시 시도하세요.
42개 모두 보기
상위 문서 유형 직함 형식 옵션 날짜
* Data sheet CC2530 datasheet (Rev. B) 2010/10/05
* Errata CC2530 Errata Note 2009/04/29
Application note AN103 -- Basic RF Testing of CCxxxx Devices (Rev. A) PDF | HTML 2025/12/11
Application note CE Regulations for SRDs Operating in License-Free 2.4GHz/5GHz Bands-WiFi Devices (Rev. A) PDF | HTML 2022/10/20
Selection guide 무선 연결 기술 선택 가이드 (Rev. B) 2022/03/07
Application note DN035 -- Antenna Quick Guide (Rev. B) 2022/02/09
Application brief What's New in Zigbee 3.0 (Rev. A) PDF | HTML 2019/06/06
Application note Debugging Communication Range (Rev. A) PDF | HTML 2019/05/23
Selection guide Zigbee® Selection Guide for SimpleLink MCUs (Rev. F) 2019/02/21
White paper Optimizing Flash and RAM Usage of Z-Stack 3.0.2 for the CC2530 Device 2018/09/25
White paper Wireless Connectivity For The Internet of Things, One Size Does Not Fit All (Rev. A) 2017/10/16
Application note ETSI EN 300 328 Blocking Test for Bluetooth Low Energy PDF | HTML 2017/02/08
Application note Using CC2592 Front End with CC2530 (Rev. A) PDF | HTML 2015/07/29
Application note RemoTI™ Capacitive Touch Sensing (Rev. B) 2014/12/16
Application note Final Test Considerations for Wireless Technology Products 2014/10/01
User guide CC253x/4x User's Guide (Rev. F) 2014/04/09
Application note AN100 - Crystal Selection Guide (Rev. C) 2013/11/26
Application note CC2530 With Skyworks’ SE2431L Range Extender Front End 2013/10/17
Application note AN084 - RemoTI SimpleConsole Application (Rev. C) 2013/03/12
Application note DN041 -- Using CC253X or CC254X with Dipole PCB Antenna 2013/01/24
Application note AN081 -- Johanson Technology Balun Optimized for CC253X, CC254X, CC257X, CC853X (Rev. B) 2012/11/06
Application note AN079 -- Measuring Power Consumption of CC2530 with Z-Stack 2012/09/28
Application note AN118 -- Flash programming of CC253x/4x devices 2012/09/05
Application note AN098 - Layout Review Techniques for Low Power RF Designs (Rev. A) 2012/08/02
Application note AN114 -- Z-Stack Duty Cycle Analysis 2011/12/12
Application note AN111 - Using RF6505 Front End Module with CC2530 under FCC 15.247 2011/11/18
Application note AN107 - Murata Balun for CC253x and CC254x, LFB182G45BG2D280 (Rev. A) 2011/10/26
Application note AN104 -- TDK Corporation balun optimized for CC253x 2011/08/10
Application note DN037 -- Measurement Results for Combined CC2530 and CC2590 Solution 2011/07/28
Application note DN034 -- YAGI 2.4 GHz PCB Antenna 2010/10/14
Application note AN058 -- Antenna Selection Guide (Rev. B) 2010/10/06
Application note DN031 -- CC-Antenna-DK Documentation and Antenna Measurements Summary 2010/08/26
Application note AN086 -- Using CC2591 Front End with CC2530 and CC2531 (Rev. A) 2009/12/16
User guide CC2530 Software Examples User's Guide (Rev. A) 2009/11/05
Design guide RemoTI HID Dongle Developer’s Guide 2009/09/24
Application note DN117 -- SimpliciTI-compatible UART Driver 2009/09/22
Application note DN112 -- Using UART in CC111xFx CC243x CC251xFx and CC253xFx (Rev. B) 2009/08/11
Application note DN113 CC111xFx CC243xFx CC251xFx CC253xFx SPI Interface (Rev. A) 2009/08/11
Application note DN116 -- Clearing Module Interrupt Flags in LPW SoC Devices 2009/08/03
Application note CC2530 FAQ (Rev. A) 2009/07/12
Application note AN074 -- RemoTI Coexistence Testing 2009/05/20
Application note Migrating From CC2430 to CC2530 2009/04/29

설계 및 개발

추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.

평가 보드

ALGO-3P-UISP1-TI — 텍사스 인스트루먼트 장치용 Algocraft μISP1 프로그래머

μISP는 호스트 PC(RS-232, USB, LAN 연결 기능이 내장되어 있음)에 연결되어 작동하거나 단독 모드로 작동할 수 있습니다.

독립 실행형 모드의 프로그래밍 싸이클은 단순히 START 버튼을 누르거나 일부 TTL 제어 라인을 통해 실행될 수 있습니다.

컴팩트한 크기와 다양한 기능을 갖추고 있어 생산 환경, 수동 및 자동 프로세스에 간편하게 통합할 수 있습니다.

발송: Algocraft
평가 보드

RDCR-3P-RADIO-MOD — Radiocrafts 임베디드 라디오 모듈

Radiocrafts’ standard RF modules provide compact, easy-to-use, low cost, low power and high-performance RF solutions for a large number of wireless applications using license-free ISM bands (169 MHz – 2.4 GHz). Using modules, OEM manufacturers without RF design knowledge can easily add (...)
발송: Radiocrafts AS
도터 카드

CC2530EMK — CC2530 평가 모듈 키트

The CC2530 Evaluation Module Kit contains two CC2530 Evaluation Modules, which can be used either as standalone modules (requires external power) or connected to e.g. the SmartRF05EB Evaluation Boards (not included in kit) for full control from the PC. The evaluation modules can be used as a (...)

사용 설명서: PDF
TI.com에서 구매할 수 없음
도터 카드

CC2531EMK — CC2531 USB 평가 모듈 키트

The CC2531EMK kit provides one CC2531 USB Dongle and documentation to support a PC interface to 802.15.4 / ZigBee applications. The dongle can be plugged directly into your PC and can be used as an IEEE 802.15.4 packet sniffer or for other purposes. With the CC2531 USB Firmware Library available on (...)

사용 설명서: PDF
TI.com에서 구매할 수 없음
디버그 프로브

CC-DEBUGGER — RF SoC(System-on-Chip)를 위한 디버거이자 프로그래머

The CC Debugger is a small programmer and debugger for the TI Low Power RF System-on-Chips. It can be used together with IAR Embedded Workbench for 8051 (version 7.51A or later) for debugging and SmartRF Flash Programmer for flash programming. The CC Debugger can also be used for controlling (...)

사용 설명서: PDF
TI.com에서 구매할 수 없음
디버그 프로브

LB-3P-TRACE32-WIRELESS — 무선 연결용 Lauterbach TRACE32® 디버그 시스템

Lauterbach의 TRACE32® 툴은 개발자가 다양한 종류의 TI 무선 연결 칩을 분석, 최적화 및 인증할 수 있도록 하는 첨단 하드웨어 및 소프트웨어 구성 요소 제품군입니다. 세계적으로 유명한 임베디드 시스템용 디버그 솔루션은 초기 사전 실리콘 개발부터 현장의 제품 인증 및 문제 해결에 이르기까지 다음을 포함하는 모든 개발 단계를 위한 완벽한 솔루션입니다.   전체 온칩 중단점 지원, 런타임 메모리 액세스, 플래시 프로그래밍 및 벤치마크 카운터. 모든 것이 스크립팅이 가능하므로 개발자는 동일한 테스트 시퀀스를 계속해서 (...)

발송: Lauterbach GmbH
하드웨어 프로그래밍 도구

ACROVIEW-3P-AP6000 — AP6000 programmer support all TI programmable chips, including EP Product, Power ICs, and Gauge ICs

AP6000, launched by Acroview, is a universal programmer designed to support TI ICs across all series. Leveraging Acroview's highly skilled algorithm R&D engineering team, it delivers the fastest chip support speed in the industry.The AP6000 is capable of programming 8 chips simultaneously, and (...)

하드웨어 프로그래밍 도구

ACROVIEW-3P-AP8000 — AP8000 Universal Programming System, including all TI programmable chips.

AP8000 is a leading technology platform of Universal Programming developed by Acroview. We have an accomplished team of algorithm R&D engineers, to offer the fastest chip support software development service among the industry. The AP8000 can support the programming of 8 chips simultaneously. (...)

하드웨어 프로그래밍 도구

ALGO-3P-WRITENOW — Algocraft WriteNow! 프로그래머

WriteNow! 시스템 내 프로그래머 시리즈는 프로그래밍 산업에서 획기적인 발전입니다. 프로그래머는 다양한 제조업체의 수많은 장치(마이크로컨트롤러, 메모리, CPLD 및 기타 프로그래머블 장치)를 지원하며 간편한 ATE/장치 통합을 위한 컴팩트한 크기를 가지고 있습니다. 이는 단독으로 작동하거나 호스트 PC(RS-232, LAN 및 USB 연결 기능이 내장되어 있음)에 연결되어 있으며 사용이 간편한 소프트웨어 유틸리티가 제공됩니다.

발송: Algocraft
코드 예제 또는 데모

SWRC135 CC2530-Software Examples

지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어

드라이버 또는 라이브러리

REMOTI — RF4CE 호환 프로토콜 스택

RemoTI™ is the industry leading ZigBee RF4CE-compliant software architecture. Built on TI's well-proven IEEE 802.15.4 compliant TIMAC, RemoTI™ offers a simple, easy-to-use, intuitive software architectural framework and all of the tools, documentation, and support needed to build an RF4CE compliant (...)
사용 설명서: PDF
드라이버 또는 라이브러리

TIMAC — IEEE802.15.4 MAC(Medium Access Control) 소프트웨어 스택

TIMAC - IEEE802.15.4 Medium Access Control (MAC) Software Stack

To download the free tools download click the "Get Software" button above. By subscribing, we will be able to notify you of updates when they become available and provide instructions on how to perform the update.

드라이버 또는 라이브러리

Z-STACK — 완전히 호환되는 ZigBee 3.x 솔루션: Z-스택

Zigbee 3.0 combines multiple previous Zigbee profiles into one unified standard
  • Incorporates the unified Zigbee Cluster Library which is at the foundation of dotdot, the universal language for IoT applications defining data objects, models and functionalities for embedded IoT applications
  • Implements (...)
드라이버 또는 라이브러리

Z-STACK-ARCHIVE — Z-Stack과 완전 호환되는 ZigBee 2012 솔루션용 아카이브

참고:

이 페이지에는 이전 버전의 Z-Stack 릴리스를 얻을 수 있는 링크가 포함되어 있습니다. 새로운 프로젝트의 경우 모든 개선 사항과 새로운 기능을 활용할 수 있도록 최신 릴리스 를 사용하는 것이 좋습니다. 최신 Z-Stack 릴리즈는 www.ti.com/z-stack에서 확인할 수 있습니다.

 

Z-Stack 홈

Z-Stack 홈은 CC2630, CC2530 및 CC2538 SoC(System-on-Chip)를 위한 TI의 ZHA(ZigBee 홈 자동화) 호환 프로토콜 스택입니다.

Z-Stack 홈에서 주목할 만한 점은 다음과 (...)

IDE, 구성, 컴파일러 또는 디버거

CCSTUDIO Code Composer Studio integrated development environment (IDE)

Code Composer Studio is an integrated development environment (IDE) for TI's microcontrollers and processors. It is comprised of a rich suite of tools used to build, debug, analyze and optimize embedded applications. Code Composer Studio is available across Windows®, Linux® and macOS® platforms.

(...)

지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어

시작 다운로드 옵션
지원 소프트웨어

PACKET-SNIFFER SmartRF™ Packet Sniffer 2.18.1

The SmartRF Packet Sniffer is a PC software application that can display and store radio packets captured by a listening RF device. The capture device is connected to the PC via USB. Various RF protocols are supported. The Packet Sniffer filters and decodes packets and displays them in a convenient (...)

지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어

지원 소프트웨어

RF-RANGE-ESTIMATOR RF Range Estimator

This tool is used to calculate a range estimate for indoor and outdoor RF links using TI wireless devices. The outdoor calculation is based upon Line-of-Sight (LOS). For the indoor estimation, construction materials can be selected that are between the Tx and Rx unit. The greater the attenuation (...)
지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어

계산 툴

SMARTRF-STUDIO-7 SmartRF Studio

SmartRF™ Studio is a Windows application that helps designers of RF systems to easily evaluate the radio at an early stage in the design process for all TI CC1xxx and CC2xxx low-power RF devices. It simplifies generation of the configuration register values and commands, as well as practical (...)

지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어

다운로드 옵션
설계 툴

3P-WIRELESS-MODULES — 타사 무선 모듈 검색 툴

타사 무선 모듈 검색 툴은 개발자가 완제품 사양을 충족하는 제품을 식별하고 생산 준비가 완료된 무선 모듈을 조달하는 데 유용합니다. 검색 툴에 포함되어 있는 타사 모듈 공급업체는 TI 무선 연결 제품을 사용하여 무선 모듈을 설계 및 제조하는 전문성을 갖춘 독립 회사입니다.
설계 툴

SIMPLELINK-2-4GHZ-DESIGN-REVIEWS — SimpleLink™ CC2xxx 장치에 대한 하드웨어 설계 검토

SimpleLink 하드웨어 설계 검토 프로세스는 설계를 검토하고 귀중한 피드백을 제공할 수 있는 주제 전문가와 일대일로 연락할 수 있는 방법을 제공합니다. 간단한 3단계 검토 요청 절차와 관련 기술 문서 및 리소스 링크는 여기서 확인할 수 있습니다.

시작하기

일반 설계 질문은 2.4GHz 하드웨어 설계 검토를 요청하기 전에 E2E 포럼에 게시해야 합니다.

하드웨어 설계 검토 요청 양식과 함께 전송할 다음 필수 문서가 준비되어 있는지 확인하세요:

  • 데이터 시트, 설계 가이드, 사용 설명서 및 기타 하드웨어 리소스와 같이 제품 (...)
회로도

STB Front Panel Schematic and PCB

SWRR080.ZIP (603 KB)

많은 TI 레퍼런스 설계에는 CC2530이(가) 포함됩니다.

레퍼런스 디자인 선택 툴을 사용하여 애플리케이션 및 매개 변수에 가장 적합한 설계를 검토하고 식별할 수 있습니다.

패키지 CAD 기호, 풋프린트 및 3D 모델
VQFN (RHA) 40 Ultra Librarian

주문 및 품질

포함된 정보:
  • RoHS
  • REACH
  • 디바이스 마킹
  • 납 마감/볼 재질
  • MSL 등급/피크 리플로우
  • MTBF/FIT 예측
  • 물질 성분
  • 인증 요약
  • 지속적인 신뢰성 모니터링
포함된 정보:
  • 팹 위치
  • 조립 위치

권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.

지원 및 교육

TI 엔지니어의 기술 지원을 받을 수 있는 TI E2E™ 포럼

콘텐츠는 TI 및 커뮤니티 기고자에 의해 "있는 그대로" 제공되며 TI의 사양으로 간주되지 않습니다. 사용 약관을 참조하십시오.

품질, 패키징, TI에서 주문하는 데 대한 질문이 있다면 TI 지원을 방문하세요. ​​​​​​​​​​​​​​

동영상