HDC3020
- Relative humidity (RH) sensor:
- Operating range: 0% to 100%
- Accuracy: ±0.5% typical
- Offset Error Correction: reduces offset to return device to within accuracy specification
- Long-term drift: 0.19%RH/yr
- Condensation protection with integrated heater
- Temperature sensor:
- Operating range: –40°C to 125°C
- Accuracy: ±0.1°C typical
- Long-term drift: ±0.03°C/yr
- NIST traceability: relative humidity & temperature
-
Output Short Circuit Protection
- Low power: average current 0.4µA
- I2C interface compatibility up to 1MHz speeds
- Four selectable I2C addresses
- Data protection through CRC checksum
- Supply voltage: 1.62V to 5.50V
- Available auto measurement mode
- Programmable interrupts
- Programmable RH and Temp measurement offset
- Factory-installed polyimide tape assembly cover
- Factory-installed IP67 rated environmental cover
The HDC302x is an integrated, capacitive based relative humidity (RH) and temperature sensor . The device provides high accuracy measurements over a wide supply range (1.62V – 5.5V) and ultra low power consumption in a compact 2.5mm × 2.5mm × 0.8mm WSON 8-pin package. Both the temperature and humidity sensors are 100% tested and trimmed on a production setup that is NIST traceable and verified with equipment that is calibrated to ISO/IEC 17025 standards.
Offset Error Correction reduces RH sensor offset due to aging, exposure to extreme operating conditions, and contaminants to return device to within accuracy specifications. For battery IoT applications, auto measurement mode and ALERT feature enable low system power by maximizing MCU sleep time. There are four different I2C addresses that support speeds up to 1MHz. A heater is available to dissipate condensation and moisture.
The HDC3020 is an open cavity package without protective cover. Two device variants have a cover option to protect the open cavity RH sensor: HDC3021 and HDC3022. HDC3021 has removable protective tape to allow conformal coatings and PCB wash. HDC3022 has a permanent IP67 filter membrane to protect against dust and water condensation.
추가 정보 요청
NIST 보정 문서를 사용할 수 있습니다. 지금 요청
관심 가지실만한 유사 제품
비교 대상 장치보다 업그레이드된 기능을 지원하는 즉각적 대체품.
기술 자료
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
HDC3020EVM — 온도 및 습도 센서용 HDC3020 평가 모듈
HDC3020EVM 평가 모듈(EVM)을 사용하면 설계자는 HDC3020 상대 습도 및 온도 센서의 작동과 성능을 평가할 수 있습니다. EVM에는 MSP430F5528 마이크로컨트롤러(µC)와 HDC3020이 탑재되어 있습니다. µC는 HDC3020을 제어하고 USB 포트를 통해 호스트 PC와 통신하는 데 사용됩니다. EVM은 필요할 경우 두 개의 섹션으로 나눌 수 있도록 설계되었습니다. 천공으로 인해 사용자가 HDC3020을 분리하여 유연하게 평가할 수 있습니다.
HDC3020FLXEVM — HDC3020 유연한 인쇄 회로 평가 모듈
ASC-STUDIO-HDC3020 — ASC studio for configuring all aspects of the HDC3020 humidity sensor
TIDA-010253 — 에너지 저장 시스템을 위한 배터리 제어 장치 레퍼런스 디자인
이 레퍼런스 디자인은 고전압 리튬 이온(리튬-이온), 리튬 인산철(LiFePO4) 배터리 랙을 위한 중앙 컨트롤러입니다. 이 디자인은 고전압 릴레이, 통신 인터페이스(RS-485, CAN(컨트롤러 영역 네트워크), 데이지 체인 및 이더넷 포함), 습도 센서에 대한 확장 가능한 인터페이스, 고전압 아날로그-디지털 컨버터(ADC) 및 전류 센서를 위한 구동 회로를 제공합니다.
이 디자인은 고성능 마이크로컨트롤러를 사용하여 애플리케이션을 개발 및 테스트합니다. 이러한 기능을 통해 고용량 배터리 랙 애플리케이션의 중앙 컨트롤러에 이 (...)
TIDA-010254 — Sub-1GHz 및 Bluetooth® 5.2 레퍼런스 설계를 지원하는 배터리 전원 mmWave 레이더 센서
이 산업용 레퍼런스 설계는 Sub-1GHz 또는 Bluetooth® 5.2 무선 통신을 지원하는 배터리 구동식 IWRL6432 60GHz mmWave 레이더 사용을 보여줍니다. 이 설계는 리튬 배터리의 인원 수 계산 및 추적, 그리고 동작 추적 애플리케이션이 시연되어 결과를 Sub-1G 또는 Bluetooth에서 원격 호스트로 전송하며 기존 IWRL6432 소프트웨어와 호환됩니다. 이 레퍼런스 설계는 PC GUI를 지원하는 LAUNCHXLCC1352R1 무선 마이크로컨트롤러 LaunchPad™를 사용하여 레이더 센서 데이터와 감지 (...)
TIDA-010997 — 에지 AI 센서 BoosterPack™ 레퍼런스 설계
이 레퍼런스 설계는 여러 TI 평가 모듈(EVM)과 호환되는 플러그 앤 플레이 방식의 시계열 센서 BoosterPack™을 소개합니다. 이 설계는 다양한 센서 유형에 대한 직접 액세스를 제공하여 CCStudio™ Edge AI Studio를 사용한 에지 AI 애플리케이션 개발 및 평가를 위해 간편하게 데이터를 수집할 수 있습니다.
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| WSON (DEF) | 8 | Ultra Librarian |