IWR1843AOP
- FMCW transceiver
- Integrated 4 receivers and 3 transmitters Antennas-On-Package (AOP)
- Integrated PLL, transmitter, receiver, Baseband, and ADC
- 76- to 81-GHz coverage with 4 GHz available bandwidth
- Ultra-accurate chirp engine based on fractional-N PLL
- TX Effective isotropic radiated power (EIRP): 16 dBm
- RX Effective isotropic noise figure: 10 dB (76 to 81 GHz)
- Phase noise at 1 MHz:
- –95 dBc/Hz (76 to 77 GHz)
- –93 dBc/Hz (77 to 81 GHz)
- Built-in
calibration and self-test (monitoring)
- Arm Cortex-R4F-based radio control system
- Built-in firmware (ROM)
- Self-calibrating system across process and temperature
- C674x DSP for FMCW signal processing
- On-chip Memory: 2MB RAM
- Arm Cortex-R4F
microcontroller for object tracking and classification, and interface control
- Supports autonomous mode (loading user application from QSPI flash memory)
- Host interface
- CAN (two instances, one being CAN-FD)
- Other interfaces
available to user application
- Up to 6 general purpose ADC channels
- Up to 2 SPI ports
- Up to 2 UARTs
- I 2C
- GPIOs
- 2-lane LVDS interface for raw ADC data and debug instrumentation
- Device Security ( on select
part numbers)
- Secure authenticated and encrypted boot support
- Customer programmable root keys, symmetric keys (256 bit), Asymmetric keys (up to RSA-2K) with Key revocation capability
- Crypto software accelerators - PKA , AES (up to 256 bit), SHA (up to 256 bit), TRNG/DRGB
- Functional safety targeted for SIL-2
- IWR1843AOP
advanced features
- Embedded self-monitoring with no host processor involvement
- Complex baseband architecture
- Embedded interference detection capability
- Programmable phase rotators in transmit path to enable beam forming
- Power management
- Built-in LDO network for enhanced PSRR
- I/Os support dual voltage 3.3 V/1.8 V
- Clock source
- Supports external oscillator at 40 MHz
- Supports externally driven clock (square/sine) at 40 MHz
- Supports 40 MHz crystal connection with load capacitors
- Easy hardware
design
- 0.8-mm pitch, 180-pin 15 mm × 15 mm flip chip BGA package (ALP) for easy assembly and low-cost PCB design
- Small solution size
- Operating
Conditions
- Junction Temperature range: –40°C to 125°C
The IWR1843AOP device is an integrated single-chip mmWave sensor based on FMCW radar technology capable of operating in the 76- to 81-GHz band with up to 4-GHz continuous chirp. The device is built with the low-power 45-nm RFCMOS process from Texas Instruments. This solution enables unprecedented levels of integration in an extremely small form factor. The IWR1843AOP is an ideal solution for low-power, self-monitored, ultra-accurate radar systems in industrial applications, such as, building automation, factory automation, drones, material handling, traffic monitoring, and surveillance.
The IWR1843AOP device is a self-contained, single-chip solution that simplifies the implementation of mmWave sensors in the band of 76 to 81 GHz. The IWR1843AOP includes a monolithic implementation of a 3TX, 4RX system with built-in PLL, and ADC converters. The IWR1843AOP also integrates a DSP subsystem, which contains a TI high-performance C674x DSP for the radar signal processing. The device includes an ARM R4F-based processor subsystem, which is responsible for front-end configuration, control, and calibration. Simple programming model changes can enable a wide variety of sensor implementation with the possibility of dynamic reconfiguration for implementing a multimode sensor. The Hardware Accelerator block (HWA) can perform radar processing and can help save MIPS on the DSP for higher-level algorithms. Additionally, the device is provided as a complete platform solution including TI reference designs, software drivers, sample configurations, API guides, training, and user documentation.
추가 정보
TI 개발자 영역을 방문하여 평가 및 개발을 시작하십시오.
기술 자료
| 상위 문서 | 유형 | 직함 | 형식 옵션 | 최신 영어 버전 다운로드 | 날짜 |
|---|---|---|---|---|---|
| * | 데이터 시트 | IWR1843AOP Single-chip 77- and 79-GHz FMCW mmWave Sensor Antennas-On-Package (AOP) datasheet | PDF | HTML | 2023. 5. 17 | |
| * | 정오표 | IWR1843AOP Device Silicon Errata Silicon Revision 1.0 | PDF | HTML | 2023. 8. 16 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
AWR1843AOPEVM — 단일 칩 76GHz~81GHz 차량용 레이더 센서용 AWR1843AOP 평가 모듈(EVM)
AWR1843 AoP(안테나 온 패키지) 평가 모듈(EVM)은 MMWAVEICBOOST 및 DCA1000EVM 개발 키트(별도 판매)에 대한 직접 연결을 사용하여 AWR1843AOP mmWave 레이더 센서를 평가하기 위한 사용하기 쉬운 플랫폼입니다.
AWR1843AOPEVM에는 온칩 C67x DSP 코어와 저전력 Arm® Cortex® R4F 프로세서용 소프트웨어 개발을 시작하는 데 필요한 모든 것이 포함되어 있습니다.
D3-3P-DESIGNCORE-RADAR — D3 임베디드 DesignCore® 레이더 평가 모듈
D3 임베디드의 미니어처 센서, 센서 평가 보드, 센서 퓨전 장치를 사용하면 TI의 mmWave 레이더 기술을 사용하여 D3 임베디드 레이더 모듈을 빠르게 평가할 수 있습니다. 이러한 센서를 사용하면 산업용 애플리케이션을 위한 레이더 알고리즘을 손쉽게 통합할 수 있습니다. 유연한 60GHz 및 77GHz 모듈에서 미니어처 안테나 온 패키지(AoP) 60GHz 및 77GHz 모듈, 유리 섬유 60GHz(77GHz 향후) 모듈의 미니어처 안테나까지 다양한 제품을 제공합니다.
HS-3P-77-3D-WGA-LOP-4X4 — HUBER+SUHNER의 ADAS 레이더 센서를 위한 안테나 설계
77GHz 3D 도파관 안테나 4TX 4R - RF 기판 독립형 솔루션 제품군
Huber+SUHNER는 RF 기판 독립 솔루션용으로 설계된 2세대 3D 금속 플라스틱 도파관 안테나를 개발 및 제조하고 있습니다. 독점 인터페이스로 구현된 이 첨단 기술은 125mm2의 소형 포트 영역에서 전체 차량용 77GHz 레이더 대역(76GHz~81GHz)을 포함하는 4TX, 4RX 구성 채널로 차세대 고밀도 LOP(Launch-on-Package) 모놀리식 마이크로파 집적 회로(MMIC)를 지원합니다. 안테나 설계는 MMIC 패키지 크기를 (...)
D3-3P-D3RCM — D3 임베디드 DesignCore® 카메라 시리즈 레거시 카메라 모듈
D3RCM 1.3 MP FPD-Link™ III 카메라는 OmniVision® OV10640 이미지 센서 또는 SONY® IMX390 이미지 센서를 탑재한 견고한 카메라 모듈입니다. 이 제품은 오토모티브 및 성능이 중요한 산업용 애플리케이션을 위해 설계된 TI 프로세서 기반의 D3 임베디드 RVP와 호환됩니다. 이 제품은 뛰어난 열 특성을 가지고 있으며 혹독한 환경 조건을 견딜 수 있습니다.
호환 하드웨어에는 TI의 TDA2X 및 TDA3X 제품군이 포함되어 있습니다.
GAPW-3P-ANTENNA — GapWaves의 ADAS 레이더 센서용 안테나 설계
Gapwaves offers high-performance, low-loss, and cost-efficient waveguide antennas for short-, mid- and long-range automotive radars and industrial applications. Our antennas feature a flexible design and a compact form factor, robust contact-free PCB integration and support contact-free LoP (...)
MMWAVE-SDK — mmWave software development kit (SDK)
mmWave SDK(소프트웨어 개발 키트)는 TI의 mmWave 센서를 이용한 애플리케이션 평가 및 개발을 지원하는 소프트웨어 패키지 컬렉션입니다. 이 툴에는 MMWAVE-SDK와 설계 요구 사항 지원을 위한 컴패니언 패키지가 포함되어 있습니다.
MMWAVE-SDK는 TI mmWave 감지 포트폴리오를 위한 통합형 소프트웨어 플랫폼으로, 설치와 설정이 간편하고 평가와 개발을 신속하게 이용할 수 있습니다. mmWave SDK의 모든 릴리스는 전체 TI mmWave 감지 포트폴리오 간에 확장되므로 장치 간에 원활한 재사용 및 (...)
CCSTUDIO — Code Composer Studio integrated development environment (IDE)
CCStudio™ IDE is part of TI's extensive CCStudio™ development ecosystem and is an integrated development environment for TI's microcontrollers, processors, wireless connectivity devices, and radar sensors. CCStudio IDE is available as desktop or cloud-based applications. The cloud version (...)
SYSCONFIG — 시스템 구성 툴
CCStudio™ SysConfig is part of TI's extensive CCStudio™ development ecosystem and is a configuration tool that simplifies hardware and software configuration challenges to accelerate software development.
SysConfig provides an intuitive graphical user interface for configuring pins, peripherals, (...)
RADAR-ACADEMY — mmWave Radar Academy
TI-DEVELOPER-ZONE — Start embedded development on your desktop or in the cloud
MMWAVE-SENSING-ESTIMATOR-CLOUD — mmWave sensing estimator cloud development on TI Resource Explorer
UNIFLASH — UniFlash for most TI microcontrollers (MCUs) and mmWave sensors
UniFlash는 TI의 광범위한 CCStudio™ 개발 에코시스템의 일부로, TI 마이크로컨트롤러 및 무선 연결 장치의 온칩 플래시와 TI 프로세서의 온보드 플래시를 프로그래밍하기 위한 소프트웨어 도구입니다. UniFlash는 그래픽 및 명령줄 인터페이스를 모두 제공하며, 데스크톱 또는 클라우드 환경에서 실행할 수 있습니다.
UniFlash는 CCStudio™ 개발자 영역의 클라우드에서 실행하거나 Windows®, Linux®, macOS® 컴퓨터에서 다운로드해 사용할 수 있습니다.
macOS는 mmWave, AMx, K2G 및 (...)
RADAR-TOOLBOX — Radar evaluation and development support package with example projects, documentation and tools
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| FCCSP (ALP) | 180 | Ultra Librarian |
주문 및 품질
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.