TLV2341
- Wide Range of Supply Voltages Over Specified Temperature Range:
- TA = -40°C to 85°C...2 V to 8 V
- Fully Characterized at 3 V and 5 V
- Single-Supply Operation
- Common-Mode Input-Voltage Range
Extends Below the Negative Rail and up to
VDD -1 V at 25°C - Output Voltage Range Includes Negative Rail
- High Input Impedance...1012 Typ
- Low Noise...25 nV/ Hz\ Typically at
f = 1 kHz (High-Bias Mode) - ESD-Protection Circuitry
- Designed-In Latch-Up Immunity
- Bias-Select Feature Enables Maximum Supply Current Range From 17 uA to
1.5 mA at 25°CLinCMOS is a trademark of Texas Instruments Incorporated.
The TLV2341 operational amplifier has been specifically developed for low-voltage, single-supply applications and is fully specified to operate over a voltage range of 2 V to 8 V. The device uses the Texas Instruments silicon-gate LinCMOSTM technology to facilitate low-power, low-voltage operation and excellent offset-voltage stability. LinCMOSTM technology also enables extremely high input impedance and low bias currents allowing direct interface to high-impedance sources.
The TLV2341 offers a bias-select feature, which allows the device to be programmed with a wide range of different supply currents and therefore different levels of ac performance. The supply current can be set at
17 uA, 250 uA, or 1.5 mA, which results in slew-rate specifications between 0.02 and 2.1 V/us (at 3 V).
The TLV2341 operational amplifiers are especially well suited to single-supply applications and are fully specified and characterized at 3-V and 5-V power supplies. This low-voltage single-supply operation combined with low power consumption makes this device a good choice for remote, inaccessible, or portable battery-powered applications. The common-mode input range includes the negative rail.
The device inputs and outputs are designed to withstand -100-mA currents without sustaining latch-up. The TLV2341 incorporates internal ESD-protection circuits that prevents functional failures at voltages up to
2000 V as tested under MIL-STD 883 C, Methods 3015.2; however, care should be exercised in handling these devices as exposure to ESD may result in the degradation of the device parametric performance.
The D package is available taped and reeled. Add R suffix to the device type (e.g., TLV2341IDR).
The PW package is only available left-end taped and reeled (e.g., TLV2341IPWLE).
기술 문서
유형 | 직함 | 날짜 | ||
---|---|---|---|---|
* | Data sheet | LinCMOS Programmable Low-Voltage Operational Amplifiers datasheet (Rev. A) | 1994/08/01 | |
E-book | The Signal e-book: A compendium of blog posts on op amp design topics | 2017/03/28 | ||
Application note | High-Voltage Signal Conditioning for Low-Voltage ADCs (Rev. B) | PDF | HTML | 2015/05/18 | |
Application note | Low-Power Signal Conditioning For A Pressure Sensor (Rev. A) | 2015/05/18 | ||
Application note | TLV2341 EMI Immunity Performance | 2013/06/09 | ||
Application note | High-Voltage Signal Conditioning for Low Voltage ADCs | 2004/06/15 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
DIP-ADAPTER-EVM — DIP 어댑터 평가 모듈
소형 표면 실장 IC(집적 회로)와 쉽고 빠르며 경제적인 방식으로 인터페이싱하는 방법을 제공하는 DIP 어댑터 평가 모듈(DIP-ADAPTER-EVM)로 연산 증폭기 프로토타이핑 및 테스트 속도를 높이세요. 제품에 포함된 Samtec 터미널 스트립을 사용하여 지원되는 연산 증폭기를 연결하거나 기존 회로에 직접 연결할 수 있습니다.
DIP 어댑터 EVM 키트는 다음을 포함해 가장 널리 사용되는 6개의 업계 표준 패키지를 지원합니다.
- D 및 U(SOIC-8)
- PW(TSSOP-8)
- DGK(MSOP-8, VSSOP-8)
- (...)
ANALOG-ENGINEER-CALC — 아날로그 엔지니어의 계산기
CIRCUIT060013 — T-네트워크 피드백 회로가 있는 인버팅 증폭기
CIRCUIT060015 — 조정 가능한 레퍼런스 전압 회로
CIRCUIT060074 — 콤퍼레이터 회로를 사용한 고압측 전류 감지
PSPICE-FOR-TI — TI 설계 및 시뮬레이션 툴용 PSpice®
TI 설계 및 시뮬레이션 환경용 PSpice는 기본 제공 라이브러리를 이용해 복잡한 혼합 신호 설계를 시뮬레이션할 수 있습니다. 레이아웃 및 제작에 (...)
TINA-TI — SPICE 기반 아날로그 시뮬레이션 프로그램
패키지 | 핀 | 다운로드 |
---|---|---|
SOIC (D) | 8 | 옵션 보기 |
주문 및 품질
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
- 팹 위치
- 조립 위치