TPSM846C26
- Small form factor 7.5mm × 8.75mm BGA package
- 3.975mm maximum height
- 2.7V to 18V input voltage with external bias
- 4V to 18V input voltage without external bias
- 0.4V to 5.5V output voltage
- Supports 35A single-phase or 2 ×, 3 ×, or 4 × stacked configurations
- Rdson_HS = 2.6mΩ, Rdson_LS = 1mΩ
- 400kHz to 2MHz operating frequency (four discrete settings through pin-strap, additional settings through PMBus®)
- PMBus
programmable
- Revision 1.5 compliant with PASSKEY security feature
- Input voltage, output voltage, output current, temperature telemetry
- Programmable overcurrent, overvoltage, undervoltage, overtemperature protections
- Includes single command write function in stacked configuration
- Extended write protection feature
- Non-volatile memory to store configuration settings
- Two methods for programming the output voltage
- Internal resistor divider (discrete settings) with boot-up voltage selected by pin-strapping
- External resistor divider (continuous settings) with boot-up voltage selected by VBOOT
- Precision voltage reference and differential
remote sense for high output accuracy
- ± 0.5% DAC accuracy from 0°C to 85°C junction
- ± 0.85% VOUT tolerance from –40°C to 125°C junction
- Selectable FCCM/DCM in single phase only
- Start-up without PMBus communication through pin-strapping
- Safe start-up into prebiased output
- 0.5ms to 16ms programmable soft-start time
- D-CAP4 control topology with fast transient response, supporting all ceramic output capacitors
- Programmable internal loop compensation
- Selectable cycle-by-cycle valley current limit
- Open-drain power-good output
The TPSM846C26 device is a highly-integrated buck module with D-CAP4 control topology for fast transient response. All programmable parameters can be configured by the PMBus interface and stored in NVM as the new default values to minimize the external component count. Pin-strap options allow for configuration as primary or secondary, stack position and stack number, DCM (single phase only) or FCCM, overcurrent limit, fault response, internal or external feedback resistor, output voltage selection or range, switching frequency, and compensation.
The PMBus interface with 1MHz clock support gives a convenient, standardized, digital interface for configuration as well as telemetry of key parameters including output voltage, output current, and internal die temperature. Response to fault conditions can be set to restart, latch off, or ignore, depending on system requirements. Two, three, and four TPSM846C26 devices can be interconnected to provide up to 140A on a single output.
The TPSM846C26 has an option to overdrive the internal 4.5V LDO with an external 5V supply through the VDRV pin to improve efficiency, reduce power dissipation, and enable start-up with a lower input voltage.
The TPSM846C26 is a lead-free device and is RoHS compliant without exemption.
기술 자료
| 상위 문서 | 유형 | 직함 | 형식 옵션 | 최신 영어 버전 다운로드 | 날짜 |
|---|---|---|---|---|---|
| * | 데이터 시트 | TPSM846C26 4V to 18V Input, 35A, 4 × Stackable, Synchronous Buck Module With PMBus and Telemetry datasheet | PDF | HTML | 2026. 10. 13 | |
| Application brief | Higher Power Density With 35A TPSM846C26 Power Module Compared to 35A TPS546C25 DC/DC Converter and Inductor | PDF | HTML | 2026. 11. 6 | ||
| Application brief | Powering FPGAs Supporting SmartVID using TI Switching Regulators and Modules With PMBus | PDF | HTML | 2026. 7. 21 | ||
| EVM User's guide | TPSM846C26 SWIFT™ Step-Down Converter Evaluation Module | PDF | HTML | 2026. 6. 23 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
TPSM846C26EVM-2PH — TPSM846C26 이중 위상 벅 평가 모듈
PMBUS-DESIGN-TOOL — Support PMBus Interface for Buck Converters and Modules
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| FCCSP (APQ) | 99 | Ultra Librarian |