MSPM0G3708
80MHz Arm® Cortex®-M0+ MCU,24 位元 7 通道 SD-ADC、256KB 快閃、32KB SRAM、CAN-FD、4 組 UART、2 組 SPI 及 2 組 I2C
MSPM0G3708
- Core
- Arm 32-bit Cortex M0+ CPU with memory protection unit, frequency up to 80MHz
- Operating characteristics
- Extended temperature: –40°C up to 125°C
- Digital Supply voltage range: 1.62V to 3.6V
- Analog Supply voltage range: 2.7V to 3.6V
- Memories
- Up to 256KB of flash memory with error correction code (ECC)
- Dual-bank with address swap for OTA updates
- 8KB data flash bank with ECC protection
- 32KB total SRAM with ECC protection or hardware parity
- Up to 256KB of flash memory with error correction code (ECC)
- High-performance analog peripherals
- Sigma delta
sub-system (SDSS) with 7 simultaneous sampling 24-bit, delta-sigma (ΔΣ),
analog-to-digital converters (SDADC) with differential inputs
- > 100 dB dynamic range at gain= 1 at 4kSps ADC data rate
- 32kSps max ADC data rate.
-
Integrated negative charge pump allows input signals below ground
- Integrated 1.2V voltage reference with low temperature drift (max 20 ppm/°C)
- Up to two simultaneous sampling 12-bit 1.6Msps, SAR analog-to-digital converters (ADC) with up to 7 external channels
- Up to two high-speed comparators (COMP) with integrated 8-bit reference DACs
- 32ns propagation delay in high-speed mode
- Support low-power mode operation down to <1µA
- Programmable analog connections between SAR ADC and COMP
-
Two voltage references (VREF) for 12-bit SAR ADC
-
Configurable 1.4V or 2.5V internal shared voltage reference with external VREF capacitor
-
Configurable 1.4V or 2.5V internal only voltage reference without external VREF capacitor
-
- Integrated temperature sensor
- Sigma delta
sub-system (SDSS) with 7 simultaneous sampling 24-bit, delta-sigma (ΔΣ),
analog-to-digital converters (SDADC) with differential inputs
- Optimized low-power modes
- RUN: 104µA/MHz (CoreMark, executed from flash)
- SLEEP: 614uA at 4MHz
- STOP: 56µA at 32kHz
- STANDBY: 1.4µA at 32kHz with RTC and SRAM state retention
- SHUTDOWN: 69nA with IO wake-up capability
- Intelligent digital peripherals
- 9-channel DMA controller
- Math accelerator supports DIV, SQRT, MAC and TRIG computations
- Five timers support up to 18 PWM channels
- One 16-bit general-purpose timers support QEI
- Two 16-bit general-purpose timers support low-power operation in STANDBY mode
- Two 16-bit advanced timers with deadband support and complimentary outputs up to 12 PWM channels
-
Two basic software timers including 4 independent configurable 16-bit counters each
-
Ability to daisy-chain 2 of the 16-bit counters to form a 32-bit counter
-
Ability to generate 2x interrupt driven PWMs per basic software timer
-
- Two windowed watchdog timers (WWDT), one independent watchdog timer (IWDT)
- RTC with alarm and calendar mode
- Enhanced communication interfaces
-
Five configurable serial interfaces (UNICOMM)
- One configurable serial interface supporting UART or SPI
-
One configurable serial interfaces supporting UART (with LIN) or I2C (controller or target mode)
-
One configurable serial interfaces supporting UART or I2C (controller or target mode)
-
One dedicated UART + LIN interface
-
One dedicated SPI interface up to 32Mbits/s
-
One Controller Area Network (CAN) interface supporting CAN 2.0 A or B and CAN-FD
-
- Clock system
- Internal 4 to 32MHz oscillator (SYSOSC) with up to ±3% accuracy
- Phase-locked loop (PLL) up to 80MHz
- Internal 32kHz low-frequency oscillator (LFOSC) with ±3% accuracy
- External 4 to 48MHz crystal oscillator (HFXT)
- External 32kHz crystal oscillator (LFXT)
- External clock input
- Data integrity and encryption
- AES-128/256 accelerator with support for GCM/GMAC, CCM/CBC-MAC, CBC, CTR
- Secure key storage for up to four AES keys
- Flexible firewalls for protecting code and data
- Cyclic redundancy checker (CRC-16, CRC-32)
- Flexible I/O features
- Up to 18 GPIOs
- Two 5V-tolerant open-drain IOs
- One high-drive IO with 20mA drive strength
- One high-speed IO
- Up to 18 GPIOs
- Development support
- 2-pin serial wire debug (SWD)
- Package options
-
40-pin VQFN (ZFU) (0.5mm pitch) (LGA carrier)
-
- Family members (also see Device Comparison)
- MSPM0G1708: 256KB flash, 32KB RAM, 8KB Databank, 7 x SDADC, 2x SAR ADC, 2x COMP, Advanced Timers
- MSPM0G3708: 256KB flash, 32KB RAM, 8KB Databank, 7 x SDADC, 2x SAR ADC, 2x COMP, Advanced Timers, 1x CAN-FD
- MSPM0G1737: 128KB flash, 32KB RAM, 8KB Databank, 7 x SDADC, 1x SAR ADC
- MSPM0G3737: 128KB flash, 32KB RAM, 8KB Databank, 7 x SDADC, 1x SAR ADC, 1x CAN-FD
- Development kits and software (also see Tools and Software)
-
LP-MSPM0G3708 Launchpad Development Kit
- MSPM0 Software Development Kit (SDK)
-
MSPM0x708 and MSPM0x737 microcontrollers (MCUs) are part of the MSP highly integrated, low-power 32-bit MCU family based on the enhanced Arm Cortex-M0+ 32-bit core platform, operating at up to 80MHz frequency. These MCUs offer a blend of cost optimization and design flexibility for applications requiring 128KB to 256KB of flash memory in a 40 pin package device. These devices include CAN-FD controllers, cybersecurity enablers, high performance integrated analog, and provide excellent low-power performance across the operating temperature range.
The device has up to 256KB of embedded flash program memory with built-in error correction code (ECC) and up to 32KB SRAM (with ECC and parity protection). The flash memory is organized into two main banks to support field firmware updates, with address swap support provided between the two main banks.
Flexible cybersecurity enablers can be used to support secure boot, secure in-field firmware updates, IP protection (execute-only memory), key storage, and more. Hardware acceleration is provided for a variety of AES symmetric cipher modes.
Sigma Delta Sub-system (SDSS) contains seven simultaneously sampling, 24-bit, delta-sigma (ΔΣ), analog-to-digital converters (ADC), offers wide dynamic range, low power, and energy-measurement-specific features, making the device an excellent fit for energy metering, power metrology, medical and test and measurement applications. The ADC inputs can be directly interfaced to a resistor divider network or a power transformer to measure voltage or to a current transformer or a Rogowski coil to measure current. A low-drift, 1.2-V reference is integrated into the AFE sub-system
The individual ADC channels can be independently configured depending on the sensor input. A low-noise, programmable gain amplifier (PGA) provides gains ranging from 1 to 128 to amplify low-level signals. Additionally, this device integrates channel to channel phase calibration and offset and gain calibration registers to help remove signal-chain errors.
A set of high performance analog modules is provided, such as two simultaneously sampling 12-bit, 1.6Msps ADCs supporting up to 7 external channels, on-chip voltage reference (1.4V or 2.5V), and two comparators operable in low-power and high-speed modes with additional built-in 8-bit reference DACs.
The TI MSPM0 family of low-power MCUs consists of devices with varying degrees of analog and digital integration. The MSPM0 MCU platform combines the Arm Cortex-M0+ platform with a holistic ultra-low-power system architecture, allowing system designers to increase performance while reducing energy consumption.
MSPM0x708 and MSPM0x737 MCUs are supported by an extensive hardware and software ecosystem with reference designs and code examples to get the design started quickly. Development kits include a LaunchPad and EVM available for purchase. TI also provides a free MSPM0 Software Development Kit (SDK), which is available as a component of Code Composer Studio™ IDE desktop and cloud version within the TI Resource Explorer. MSPM0 MCUs are also supported by extensive online collateral, training with MSP Academy, and online support through the TI E2E™ support forums.
For complete module descriptions, see the MSPM0 G-Series 80MHz Microcontrollers Technical Reference Manual.
技術文件
| 重要文件 | 類型 | 標題 | 格式選項 | 下載最新的英文版本 | 日期 | |
|---|---|---|---|---|---|---|
| * | 資料表 | MSPM0x708, MSPM0x737 Mixed-Signal Microcontrollers with 7 Sigma-Delta ADCs and CAN-FD Interface datasheet | PDF | HTML | 2026/10/15 | ||
| * | 使用指南 | MSPM0 G-Series 80-MHz Microcontrollers Technical Reference Manual (Rev. F) | PDF | HTML | 2026/11/5 |
設計與開發
如需其他條款或必要資源,請按一下下方的任何標題以檢視詳細頁面 (如有)。
LP-MSPM0G3708 — MSPM0G3708 LaunchPad™ 開發套件
The MSPM0G3708 LaunchPad™ development kit is an evaluation module for the MSPM0G3708 microcontroller (MCU). The LaunchPad kit contains everything needed to start development on the MSPM0Gx70x and MSPM0Gx73x microcontroller platform, including an onboard debug probe for programming, debugging, (...)
MSPM0-SDK — MSPM0 Software Development Kit (SDK)
MSPM0 SDK 提供軟體、工具和文件的終極集合,可使用單一軟體套件,加速開發 MSPM0 MCU 平台的應用。
MSPM0-ZEPHYR-SDK — Zephyr SDK for MSPM0 Devices
MSPM0 SDK 提供軟體、工具和文件的終極集合,可使用單一軟體套件,加速開發 MSPM0 MCU 平台的應用。
CCSTUDIO — Code Composer Studio™ integrated development environment (IDE)
CCStudio™ IDE is an integrated development environment designed for Texas Instruments' embedded processors, available as both a desktop and cloud-based application. It is an integral part of TI's extensive CCStudio™ development ecosystem.
CCStudio IDE is built on Eclipse Theia™ framework, the (...)
CCSTUDIO-OPENOCD — OpenOCD Binary Releases
MSP-ZERO-CODE-STUDIO — Graphical development environment for designing applications for MSP microcontrollers
MSP Zero Code Studio 是一款可簡化韌體開發的視覺設計環境,並且能在數分鐘內設定、開發及執行微控制器應用程式,無須編碼,也不需要 IDE。提供獨立下載或雲端版本。
SYSCONFIG — Standalone desktop version of SysConfig
CCStudio™ SysConfig is part of TI's extensive CCStudio™ development ecosystem and is a configuration tool that simplifies hardware and software configuration challenges to accelerate software development.
SysConfig provides an intuitive graphical user interface for configuring pins, peripherals, (...)
MSPM0-ACADEMY — MSPM0™ academy
CCSTUDIO-STARTHUB — Example application browser
MSP-MOTOR-CONTROL — MSPM0 Firmware solutions for motor control applications
MSP 馬達控制為一系列軟體、工具和範例,可在 30 分鐘或更短時間內運用 MSPM0 Arm® Cortex® M0+ MCU 和熱門馬達驅動器解決方案來運轉馬達。
MSP 馬達控制提供可轉動有刷、步進與三相馬達的受支援硬體套件範例,具備最佳性能、整合性與易用性的感測和無感測器控制演算法。透過訂購硬體、連接馬達及使用我們的圖形使用者介面或線上程式碼範例,可隨時運轉您的馬達。
TI-DEVELOPER-ZONE — Start embedded development on your desktop or in the cloud
ENERGY-METROLOGY-STUDIO-DESIGN — Secure release for TI Energy Metrology Studio graphical configuration tool
LP-MSPM0G3507-OOBE — Out-of-box experience GUI for LP-MSPM0G3507
MSPM0-ANALOG-CONFIGURATOR — Analog Configurator for MSPM0
MSPM0 類比配置器是一款圖形配置工具,旨在使用 MSPM0 裝置簡化和加速類比訊號鏈的設計和實現,無需進行傳統的程式碼開發。
此工具使用直覺式 GUI,透過 MSPM0 裝置的高類比整合配置訊號鏈,即時分析和繪製訊號,並產生快閃裝置所需的配置和程式碼。
MSP-GANG-SOFTWARE — MSP-GANG Software
UNIFLASH — UniFlash for most TI microcontrollers (MCUs) and mmWave sensors
UniFlash 是 TI 龐大 CCStudio™ 開發生態系統的一部分,是一款用於在 TI 微控制器與無線連線裝置上對晶片內快閃記憶體進行燒錄,以及在 TI 處理器上對板載快閃記憶體進行燒錄的軟體工具。UniFlash 提供圖形化介面與命令行介面,並可在桌面上或雲端中執行。
UniFlash 可從 CCStudio™ 開發人員區上的雲端執行,或在下載後於 Windows®、Linux® 和 macOS® 電腦中使用。
請注意,mmWave、AMx、K2G 和 J7 裝置不支援 macOS。AMx、K2G 和 J7 裝置僅於命令列上支援。
| 封裝 | 針腳 | CAD 符號、佔位空間與 3D 模型 |
|---|---|---|
| LGA (ZFU) | 40 | Ultra Librarian |
訂購與品質
建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。