首頁 介面 I2C & I3C ICs I2C 通用 I/O (GPIO)
首頁
介面
I2C & I3C ICs
I2C 通用 I/O (GPIO)

TCAL6408

現行

具有中斷、重設和快捷 I/O 配置的 8 位轉換 I²C-bus/SMBus I/O 擴展器

立即訂購
產品規格表

TCAL6408

現行
產品規格表 立即訂購

產品詳細資料

Number of I/Os 8 Features 1-MHz maximum frequency, Adjustable I/O level, Configuration registers, Interrupt pin, Reset pin Supply voltage (min) (V) 1.08 Supply voltage (max) (V) 3.6 Addresses 2 Rating Catalog Frequency (max) (MHz) 1 Operating temperature range (°C) -40 to 125
Number of I/Os 8 Features 1-MHz maximum frequency, Adjustable I/O level, Configuration registers, Interrupt pin, Reset pin Supply voltage (min) (V) 1.08 Supply voltage (max) (V) 3.6 Addresses 2 Rating Catalog Frequency (max) (MHz) 1 Operating temperature range (°C) -40 to 125
TSSOP (PW) 16 32 mm² 5 x 6.4 UQFN (RSV) 16 4.68 mm² 2.6 x 1.8 X2QFN (DTU) 16 2.56 mm² 1.6 x 1.6
  • Operating power-supply voltage range of 1.08 V to 3.6 V
  • Allows bidirectional voltage-level translation and GPIO expansion between 1.2-V, 1.8-V, 2.5-V, and 3.3-V I 2C bus and p-ports
  • Low standby current consumption of 1 µA typical at 1.8 V
  • 1-MHz fast mode plus I 2C bus
  • Hardware address pin allows two devices on the same I 2C, SMBus bus
  • Active-low reset input ( RESET )
  • Open-drain active-low interrupt output ( INT )
  • Input or output configuration register
  • Polarity inversion register
  • Configurable I/O drive strength register
  • Pull-up and pull-down resistor configuration register
  • Internal power-on reset
  • Noise filter on SCL or SDA inputs
  • Latched outputs with high-current drive maximum capability for directly driving LEDs
  • Latch-up performance exceeds 100 mA per JESD 78, class II
  • ESD protection exceeds JESD 22
    • 4000-V Human-body model (A114-A)
    • 1000-V Charged-device model (C101)
  • Operating power-supply voltage range of 1.08 V to 3.6 V
  • Allows bidirectional voltage-level translation and GPIO expansion between 1.2-V, 1.8-V, 2.5-V, and 3.3-V I 2C bus and p-ports
  • Low standby current consumption of 1 µA typical at 1.8 V
  • 1-MHz fast mode plus I 2C bus
  • Hardware address pin allows two devices on the same I 2C, SMBus bus
  • Active-low reset input ( RESET )
  • Open-drain active-low interrupt output ( INT )
  • Input or output configuration register
  • Polarity inversion register
  • Configurable I/O drive strength register
  • Pull-up and pull-down resistor configuration register
  • Internal power-on reset
  • Noise filter on SCL or SDA inputs
  • Latched outputs with high-current drive maximum capability for directly driving LEDs
  • Latch-up performance exceeds 100 mA per JESD 78, class II
  • ESD protection exceeds JESD 22
    • 4000-V Human-body model (A114-A)
    • 1000-V Charged-device model (C101)

The TCAL6408 device provides general purpose parallel input/output (I/O) expansion for the two-line bidirectional I 2C bus (or SMBus) protocol. The device can operate with a power supply voltage ranging from 1.08 V to 3.6 V on the I 2C bus side (V CCI) and a power supply voltage ranging from 1.08 V to 3.6 V on the P-port side (V CCP).

The device supports 100-kHz (Standard-mode), 400-kHz (Fast-mode), and 1-MHz (fast-mode-plus) I 2C clock frequencies. I/O expanders such as the TCAL6408 provide a simple solution when additional I/Os are needed for switches, sensors, push-buttons, LEDs, fans, and so on.

The TCAL6408 has Agile I/O ports which include additional features designed to enhance the I/O performance in terms of speed, power consumption and EMI. The additional features are: programmable output drive strength, programmable pull-up and pull-down resistors, latchable inputs, maskable interrupt, interrupt status register, and programmable open-drain or push-pull outputs.

The TCAL6408 device provides general purpose parallel input/output (I/O) expansion for the two-line bidirectional I 2C bus (or SMBus) protocol. The device can operate with a power supply voltage ranging from 1.08 V to 3.6 V on the I 2C bus side (V CCI) and a power supply voltage ranging from 1.08 V to 3.6 V on the P-port side (V CCP).

The device supports 100-kHz (Standard-mode), 400-kHz (Fast-mode), and 1-MHz (fast-mode-plus) I 2C clock frequencies. I/O expanders such as the TCAL6408 provide a simple solution when additional I/Os are needed for switches, sensors, push-buttons, LEDs, fans, and so on.

The TCAL6408 has Agile I/O ports which include additional features designed to enhance the I/O performance in terms of speed, power consumption and EMI. The additional features are: programmable output drive strength, programmable pull-up and pull-down resistors, latchable inputs, maskable interrupt, interrupt status register, and programmable open-drain or push-pull outputs.
open-in-new 尋找其它 I2C 通用 I/O (GPIO)
下載 觀看有字幕稿的影片 影片

技術文件

star =TI 所選的此產品重要文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 2
類型 標題 日期
* Data sheet TCAL64088-Bit Translating I2C-Bus, SMBus I/O Expander With Interrupt Output, Reset, and Agile I/O Configuration Registers datasheet (Rev. B) PDF | HTML 2023年 11月 7日
Application note Features of TCAL Agile I/O Expanders PDF | HTML 2023年 6月 6日

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

IO-EXPANDER-EVM — IO-EXPANDER-EVM：I2C 和 SMBus IO 擴展器評估模組

IO 擴展器評估模組 (EVM) 可讓您評估 TI 的 SMBus 與 I2C IO 擴展器線路裝置產品組合。TCA6424A 和 TCA9539 都安裝在電路板上。24 針腳 TSSOP 元件封裝還支援 TCA6408A、TCA6416A、TCA9534、TCA9534A、TCA9535、TCA9538, TCA9554、TCA9554A 和 TCA9555。

使用指南: PDF
TI.com 無法提供
模擬工具

PSPICE-FOR-TI — PSpice® for TI 設計與模擬工具

PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
要求
模擬工具

TINA-TI — 基於 SPICE 的類比模擬程式

TINA-TI provides all the conventional DC, transient and frequency domain analysis of SPICE and much more. TINA has extensive post-processing capability that allows you to format results the way you want them. Virtual instruments allow you to select input waveforms and probe circuit nodes voltages (...)
使用指南: PDF
檢視選項
封裝 引腳 下載
TSSOP (PW) 16 檢視選項
UQFN (RSV) 16 檢視選項
X2QFN (DTU) 16 檢視選項
適用 TI 的評估品項標準條款與條件。

訂購與品質

內含資訊：
  • RoHS
  • REACH
  • 產品標記
  • 鉛塗層/球物料
  • MSL 等級/回焊峰值
  • MTBF/FIT 估算值
  • 材料內容
  • 資格摘要
  • 進行中可靠性監測
內含資訊：
  • 晶圓廠位置
  • 組裝地點

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片