The UCD3138 is a digital power supply controller offering superior levels of integration and performance in a single-chip solution. The flexible nature of the UCD3138 makes it suitable for a wide variety of power conversion applications. In addition, multiple peripherals inside the device have been specifically optimized to enhance the performance of AC-DC and isolated DC-DC applications and reduce the solution component count in the IT and network infrastructure space.
The UCD3138 controller is a fully programmable solution offering customers complete control of their application, along with ample ability to differentiate their solution. At the same time, TI is committed to simplifying our customers’ development effort by offering best-in-class development tools, including application firmware, Code Composer Studio™ software development environment, and TI’s power development GUI which lets customers configure and monitor key system parameters.
At the core of the UCD3138 controller are the digital control loop peripherals, also known as Digital Power Peripherals (DPPs). Each DPP implements a high-speed digital control loop consisting of a dedicated Error Analog-to-Digital Converter (EADC), a PID-based 2-pole/2-zero digital compensator and DPWM outputs with 250-ps pulse width resolution. The device also contains a 12-bit, 267-ksps general-purpose ADC with up to 15 channels, timers, interrupt control, PMBus, and UART communications ports. The device is based on a 32-bit ARM7TDMI-S RISC microcontroller that performs real-time monitoring, configures peripherals, and manages communications. The ARM microcontroller executes its program out of programmable flash memory as well as on-chip RAM and ROM.
In addition to the FDPP, specific power management peripherals have been added to enable high efficiency across the entire operating range, high integration for increased power density, reliability, and lowest overall system cost and high flexibility with support for the widest number of control schemes and topologies. Such peripherals include: light load burst mode, synchronous rectification, LLC and phase-shifted full bridge mode switching, input voltage feed forward, copper trace current sense, ideal diode emulation, constant current constant power control, synchronous rectification soft on and off, peak current mode control, flux balancing, secondary side input voltage sensing, high-resolution current sharing, hardware-configurable soft start with pre bias, as well as several other features. Topology support has been optimized for voltage mode and peak current mode controlled phase-shifted full bridge, single and dual phase PFC, bridgeless PFC, hard-switched full bridge and half bridge, and LLC half bridge and full bridge.
如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。
UCD3138ALLCEVM150 是評估模組 (EVM) 電路板，可作為 LLC 諧振半橋 dc-dc 轉換器，並由控制卡 UCD3138ACCEVM149 進行數位控制。此 EVM 用於在 LLC 諧振半橋 dc-dc 轉換應用中，使用 UCD3138A 來評估數位電源控制。EVM 接受 350Vdc 至 400Vdc 的 dc 線路輸入、額定輸出電壓 12Vdc、輸出全負載功率 340W，峰值效率超過 94%，受益於二次側同步整流器運作。EVM 具備各種保護功能，例如輸入線路欠電壓、輸出過電壓與過電流限制、緩啟動及減少輕負載功率損耗。EVM (...)
德州儀器 UCD3138HSFBEVM-029 評估模組 (EVM) 是以 UCD3138RHA 可編程數位電源控制器為架構的數位控制硬切換全橋轉換器。EVM 是一款專為 48V 輸入系統設計的獨立對稱式硬切換全橋 (HSFB) DC-DC 電源轉換器。UCD3138HSFBEVM-029 接受 36 至 72Vdc 的 DC 輸入，並輸出額定 12Vdc、全輸出負載功率 360W 或全輸出電流 30A。防護功能包括過電壓、欠電壓、過電流和過熱。功能包括輸入電壓前饋、預偏壓啟動與 PMBus 通訊。UCD3138HSFBEVM-029 也隨附 USB-TO-GPIO (...)
德州儀器 UCD3138PFCEVM-026 評估模組 (EVM) 是以 UCD3138 可編程數位電源控制器為架構的數位控制單相 PFC 前置穩壓器。EVM 可接受 90Vac 至 264Vac、47Hz 至 63Hz 的通用 AC 線路輸入。額定輸出電壓為 390VDC。輸出全負載功率為 360W，且在大多數操作條件下，功率因數高於 0.999，THD 低於 5%。評估模組的防護功能包括暫時低壓、輸出過電壓和啟動突波電流限制。評估模組可透過硬體和韌體更新重新配置為雙相交錯式 PFC 或無橋接 PFC 拓撲結構。此評估模組也可使用自訂韌體重新編程，以便使用者能依自身需求新增功能。
(...)
德州儀器 UCD3138CC64EVM-030 評估模組 (EVM) 可作為 UCD3138 數位控制器的控制卡，適用於德州儀器的隔離電源應用。EVM 可作為獨立電路板研究 UCD3138 裝置，或作為控制卡使用，用於根據 PFC、半橋諧振 LLC 和相移全橋等拓撲結構實作全穩壓電源轉換器。這是透過將適當的韌體下載至 EVM 的 UCD3138 裝置，並從終端使用者建立與合適的功率級電路板介面實作。為了協助評估常見的隔離式電源拓撲結構，UCD3138CC64EVM-030 評估模組的設計可與德州儀器的 UCD3138PFCEVM-026 數位 PFC 前置穩壓器 (...)
德州儀器 XDS110 是一種全新的偵錯探測器 (模擬器) 類別，適用於 TI 嵌入式處理器。XDS110 取代 XDS100 系列，可在單一 Pod 中支援更廣泛的標準 (IEEE1149.1、IEEE1149.7、SWD)。同時，所有 XDS 偵錯探針在所有配備嵌入式追蹤緩衝器 (ETB) 的 Arm® 與 DSP 處理器中均支援核心與系統追蹤。 對於針腳上的核心追蹤，則需要 XDS560v2 PRO TRACE。
德州儀器 XDS110 透過 TI 20 針腳連接器（具有用於 TI 14 針腳和 Arm 10 針腳和 Arm 20 針腳的多轉接器）連接到目標電路板，並透過 USB2.0 (...)
XDS560v2 是 XDS560™ 偵錯探測器系列的最高性能表現，支援傳統 JTAG 標準 (IEEE1149.1) 和 cJTAG (IEEE1149.7)。請注意，序列線偵錯 (SWD) 不受支援。
所有 XDS 偵錯探測器均支援所有具有嵌入式追踪緩衝區 (ETB) 的 ARM 和 DSP 處理器中的核心和系統追蹤功能。對於針腳追蹤則需要 XDS560v2 PRO TRACE。
XDS560v2 透過 MIPI HSPT 60 針腳接頭 (具有用於 TI 14 針腳、TI 20 針腳和 ARM 20 針腳的多轉接器) 連接到目標電路板，並透過 USB2.0 高速 (480Mbps) (...)
The XDS560v2 is the highest performance of the XDS560™ family of debug probes and supports both the traditional JTAG standard (IEEE1149.1) and cJTAG (IEEE1149.7). Note that it does not support serial wire debug (SWD).
All XDS debug probes support Core and System Trace in all ARM and DSP processors (...)
UCD3138 non isolated bi-directional switching converter quickly gets a designer through evaluation to production in power supply designs based on a Wide Vin non isolated bi-directional topology by providing all-inclusive firmware with ZVS Transition mode support.
UCD3138 Phase Shift LLC quickly gets a designer through evaluation to production in power supply designs based on a resonant LLC topology by providing firmware with ZVS operation and mode switching capability to achieve high efficiency across wider operating conditions.
The resonant LLC topology (...)
UCD3138 Hard Switched Full Bridge (HSFB) topology firmware gets a designer through evaluation to production in power supply designs based on high power Hard Switched Full Bridge topology by providing all-inclusive firmware with input voltage feed forward, copper trace current sensing, on the fly (...)
UCD3138 Power Factor Correction (PFC) firmware gets a designer through evaluation to production in power supply designs based on a PFC topology by providing all-inclusive firmware that can integrate easily with your housekeeping functionality.
UCD3138 Phase Shift Full Bridge quickly gets a designer through evaluation to production in power supply designs based on high power PSFB topology by providing all-inclusive firmware with peak current mode control support, adaptive dead time optimization and programmable slope compensation.
UCD3138 Resonant LLC Programmer quickly gets a designer through evaluation to production in power supply designs based on a resonant LLC topology by providing firmware with ZCS protection and mode switching capability to achieve high efficiency across wider operating conditions. The sunflower (...)
The Fusion Digital Power Studio is built on top of a Microsoft.NET Application Programming Interface (Fusion-API) that handles I2C/SMBus communication and abstracts devices and commands. It provides high level interfaces to common tasks such as command read/write, full device configuration (...)
Fusion Digital PowerTM Studio incorporates software tools for Texas Instruments' UCD3138 Integrated Digital Controller family. Fusion Digital Power helps power supply engineers to gain benefits of digital power without learning complex programming skills. Fusion Digital Power is an intuitive (...)
| 封裝 | 針腳 | CAD 符號、佔位空間與 3D 模型 |
|---|---|---|
| VQFN (RGC) | 64 | Ultra Librarian |
| VQFN (RHA) | 40 | Ultra Librarian |
| VQFN (RJA) | 40 | Ultra Librarian |
| WQFN (RMH) | 40 | Ultra Librarian |
建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。