TPS2511
- Supports a USB DCP Shorting D+ Line to D– Line
- Supports a USB DCP Applying 2 V on D+ Line and 2.7 V on D– Line (or a USB DCP Applying
2.7 V on D+ Line and 2 V on D– Line) - Supports a USB DCP Applying 1.2 V on D+ and D– Lines
- Automatically Switch D+ and D– Lines Connections for an Attached Device
- Hiccup Mode for Output Short-Circuit Protection
- Provides CS Pin for USB Cable Compensation
- Programmable Current Limit (ILIM_SET Pin)
- Accurate ±10% Current Limit at 2.3 A (Typical)
- 70-mΩ (Typical) High-Side MOSFET
- Compatible With USB 2.0 and 3.0 Power Switch Requirements
- Operating Range: 4.5 V to 5.5 V
- Available in 8-Pin MSOP-PowerPAD™ Package
The TPS2511 device is a USB-dedicated charging port (DCP) controller and current-limiting power switch. An auto-detect feature monitors USB data line voltage, and automatically provides the correct electrical signatures on the data lines to charge compliant devices among the following dedicated charging schemes:
- Divider DCP, required to apply 2.7 V and 2 V on the D+ and D– lines respectively or 2 V and 2.7 V on the D+ and D– lines respectively
- BC1.2 DCP, required to short the D+ line to the D– line1.2 V on both D+ and D– lines
The TPS2511 is a 70-mΩ power-distribution switch intended for applications where heavy capacitive loads and short circuits are likely to be encountered. This device also provides hiccup mode when the output (OUT) voltage is less than 3.8 V (typical) or when an overtemperature protection occurs during an overload condition. Accurate and programmable current limit provides flexibility and convenience for applications. The TPS2511 provides a CS pin for USB cable resistance compensation and an EN pin to control the device turnon and turnoff.
기술 문서
유형 | 직함 | 날짜 | ||
---|---|---|---|---|
* | Data sheet | TPS2511 USB Dedicated Charging Port Controller and Current Limiting Power Switch datasheet (Rev. A) | PDF | HTML | 2015/08/05 |
Selection guide | Power Management Guide 2018 (Rev. R) | 2018/06/25 | ||
Selection guide | USB Type-A Power Switch and Charging Controller Selector Guide (Rev. F) | 2018/05/24 | ||
Application note | Effective System ESD Protection Guidelines:TPS251x USB Charging Port Controllers | 2016/07/19 | ||
Technical article | Power Tips: Don’t let a drooping USB voltage slow down your charger | PDF | HTML | 2015/10/30 | |
Application note | Creating a Universal Car Charger for USB Devices From the TPS54240 and TPS2511 (Rev. E) | 2013/09/16 | ||
Test report | Test Report for the iPad Automotive Charger | 2013/06/11 | ||
Application note | Optimizing Li-ion Power Pack Performance | 2012/10/04 | ||
Application note | Creating a Dual USB Universal Car Charger From the TPS40170 and Two TPS2511 | 2012/05/22 | ||
EVM User's guide | Using the TPS2511EVM | 2012/05/04 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
TPS2511EVM-141 — TPS2511 평가 모듈
TIDA-01253 — CISPR 25 클래스 4 오토모티브 듀얼 원격 및 로컬 USB 포트 레퍼런스 설계
PMP8851 — 자동차 USB 배터리 충전기 레퍼런스 디자인
PMP9594 — BJT 스위치를 사용하는 PSR 플라이백 기반 자동 감지를 지원하는 85-265VACin, 5V/1.5A AC/DC USB 충전기
PMP4344 — <10mW 무부하 전원의 범용 AC 입력 5V@1.2A 큐브 충전기
PMP8363 — 태블릿 및 스마트폰용 85VAC-265VAC 입력, 5V@2A 에코 충전기 레퍼런스 디자인
PMP8286 — 범용 AC 입력, 5V@2.1A 스마트 USB 충전기 큐브
PMP7390 — 듀얼 포트 자동차 USB 충전기 레퍼런스 디자인
패키지 | 핀 | 다운로드 |
---|---|---|
HVSSOP (DGN) | 8 | 옵션 보기 |
주문 및 품질
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
- 팹 위치
- 조립 위치