SLVSE65C July 2018 – December 2023 DRV8847
PRODUCTION DATA
Refer to the PDF data sheet for device specific package drawings
| PIN | TYPE(1) | DESCRIPTION | |||
|---|---|---|---|---|---|
| NAME | DRV8847 | DRV8847S | |||
| TSSOP HTSSOP |
WQFN | TSSOP | |||
| GND | 13 | 11 | 13 | PWR | Device ground. Recommended to connect the GND pin and device thermal pad (HTSSOP and WQFN packages) to ground |
| IN1 | 16 | 14 | 16 | I | Half-bridge input 1 |
| IN2 | 15 | 13 | 15 | I | Half-bridge input 2 |
| IN3 | 9 | 7 | 9 | I | Half-bridge input 3 |
| IN4 | 10 | 8 | 10 | I | Half-bridge input 4 |
| ISEN12 | 3 | 1 | 3 | O | Full-bridge-12 sense. Connect this pin to the current sense resistor for full-bridge-12. Connect this pin to the GND pin if current regulation is not required. |
| ISEN34 | 6 | 4 | 6 | O | Full-bridge-34 sense. Connect this pin to the to current sense resistor for full-bridge-34. Connect this pin to the GND pin if current regulation is not required. |
| MODE | 14 | 12 | — | I | Tri-state pin for selection of driver operating mode |
| nFAULT | 8 | 6 | 8 | OD / I | Fault indication pin. This pin is pulled logic low with a fault condition. This open-drain output requires an external pullup resistor. This pin is also used as an input pin for the DRV8847S device for releasing the I2C bus. |
| nSLEEP | 1 | 15 | 1 | I | Sleep mode input. Set this pin to logic high to enable the device. Set this pin to logic low to go to low-power sleep mode |
| OUT1 | 2 | 16 | 2 | O | Half-bridge output 1 |
| OUT2 | 4 | 2 | 4 | O | Half-bridge output 2 |
| OUT3 | 7 | 5 | 7 | O | Half-bridge output 3 |
| OUT4 | 5 | 3 | 5 | O | Half-bridge output 4 |
| SCL | — | — | 11 | I | I2C clock signal. |
| SDA | — | — | 14 | OD | I2C data signal. The SDA pin requires a pullup resistor. |
| TRQ | 11 | 9 | — | I | Torque current scalar |
| VM | 12 | 10 | 12 | PWR | Power supply. Connect the VM pin to the motor power supply. Bypass this pin to ground with a VM-rated 0.1-µF (ceramic) and 10-μF (minimum) capacitor. |
| PIN | TYPE(1) | DESCRIPTION | |
|---|---|---|---|
| DRV8471 WQFN | NO. | ||
| GND | 11 | PWR | Device ground. Recommended to connect the GND pin and device thermal pad to ground |
| IN1 | 14 | I | Half-bridge input 1 |
| IN2 | 13 | I | Half-bridge input 2 |
| IN3 | 7 | I | Half-bridge input 3 |
| IN4 | 8 | I | Half-bridge input 4 |
| ISEN12 | 1 | O | Full-bridge-12 sense. Connect this pin to the current sense resistor for full-bridge-12. Connect this pin to the GND pin if current regulation is not required. |
| ISEN34 | 4 | O | Full-bridge-34 sense. Connect this pin to the to current sense resistor for full-bridge-34. Connect this pin to the GND pin if current regulation is not required. |
| NC | 9 | - | No connect |
| NC | 12 | - | No connect |
| nFAULT | 6 | OD | Fault indication pin. This pin is pulled logic low with a fault condition. This open-drain output requires an external pullup resistor. |
| nSLEEP | 15 | I | Sleep mode input. Set this pin to logic high to enable the device. Set this pin to logic low to go to low-power sleep mode. |
| OUT1 | 16 | O | Half-bridge output 1 |
| OUT2 | 2 | O | Half-bridge output 2 |
| OUT3 | 5 | O | Half-bridge output 3 |
| OUT4 | 3 | O | Half-bridge output 4 |
| VM | 10 | PWR | Power supply. Connect the VM pin to the motor power supply. Bypass this pin to ground with a VM-rated 0.1-µF (ceramic) and 10-μF (minimum) capacitor. |