SLVSJQ6A September   2025  – June 2026 TMF0064

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements
    7. 5.7 Functional Tests
    8. 5.8 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 64768-Bit FRAM
      2. 6.3.2 FRAM Status Memory
      3. 6.3.3 Address Registers and Transfer Status
      4. 6.3.4 Writing Data to the FRAM
      5. 6.3.5 TMF0064 Device ID
      6. 6.3.6 Bus Termination
    4. 6.4 Device Functional Modes
      1. 6.4.1 Test Procedures for Functional Tests
        1. 6.4.1.1 Multiple Target Configurations
    5. 6.5 Programming
      1. 6.5.1 Serial Communication
      2. 6.5.2 Initialization
      3. 6.5.3 ROM Commands
        1. 6.5.3.1 READ ROM Command [33h]
        2. 6.5.3.2 MATCH ROM Command [55h]
        3. 6.5.3.3 SKIP ROM Command [CCh]
        4. 6.5.3.4 SEARCH ROM Command [F0h]
        5. 6.5.3.5 RESUME Command [A5h]
        6. 6.5.3.6 OVERDRIVE SKIP ROM Command [3Ch]
        7. 6.5.3.7 OVERDRIVE MATCH ROM Command [69h]
      4. 6.5.4 Memory Function Commands
        1. 6.5.4.1 Write Scratchpad Command [0Fh]
        2. 6.5.4.2 Read Scratchpad Command [AAh]
        3. 6.5.4.3 Copy Scratchpad [55h]
        4. 6.5.4.4 Read Memory [F0h]
        5. 6.5.4.5 Extended Read Memory [A5h]
        6. 6.5.4.6 Memory Command Flow Charts
      5. 6.5.5 SDQ Signaling
        1. 6.5.5.1 RESET and PRESENCE PULSE
        2. 6.5.5.2 Write-Read-Time Slots
      6. 6.5.6 IDLE
      7. 6.5.7 CRC Generation
  8. 7 Application and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Application
      1. 7.2.1 Design Requirements
      2. 7.2.2 Detailed Design Procedure
      3. 7.2.3 Application Curves
    3. 7.3 Power Supply Recommendations
    4. 7.4 Layout
      1. 7.4.1 Layout Guidelines
      2. 7.4.2 Layout Example
  9. 8 Device and Documentation Support
    1. 8.1 Receiving Notification of Documentation Updates
    2. 8.2 Support Resources
    3. 8.3 Trademarks
    4. 8.4 Electrostatic Discharge Caution
    5. 8.5 Glossary
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information
    1. 10.1 Packaging Information
    2. 10.2 Tape and Reel Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

Writing Data to the FRAM

The TMF0064 device does not allow writes to the FRAM memory directly by the host. Achieve writing to the FRAM memory directly by the host by using the scratchpad as an interim repository. To write into the scratchpad, the host first issues the Write Scratchpad command followed by the desired target address and the data to write into the scratchpad. Depending on the conditions the Write Scratchpad Command section describes, the host can receive an inverted CRC16 of the entire write scratchpad sequence (the write scratchpad is commanded, the address and the data) at the end of the Write Scratchpad command sequence.

If the host receives the CRC16 value, the host can compare the received value to the expected computed value. If there is a match, the write scratchpad communication is successful and the host decides on whether to proceed to the Copy Scratchpad command.

If the host does not receive the CRC16 value, then the host can use the Read Scratchpad command to verify integrity of the data stored in the scratchpad. After receiving the Read Scratchpad command, the TMF0064 initially transmits the contents of the target address registers (TA1, TA2) and the E/S register. If the PF flag is set, or if the AA flag is set but PF flag cleared, the previous Write Scratchpad command is not successful. In this case, the host can terminate the Read Scratchpad sequence and start another attempt to write data to the scratchpad. If the previous Write Scratchpad is successful, both flags are cleared and the E[4:0] that is read indicates the address of the last byte written to the scratchpad. In this case, the host can continue reading from the TMF0064, verifying all the data bytes. If there is a match, the host can send the Copy Scratchpad command followed by the exact data of the registers TA1, TA2, and E/S that the host obtained by reading the scratchpad. At the end of the Copy Scratchpad sequence, if the authorization pattern matches, the TMF0064 starts copying the scratchpad data to the requested location, provided copy protection is not set, the PF flag is cleared, and there are no Read Memory or Extended Read Memory commands issued between Write and Copy Scratchpad commands.