JAJSDY1C June   2017  – March 2018 TPS25740B

PRODUCTION DATA.  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
    1.     Device Images
      1.      概略回路図
  4. 4 改訂履歴
  5. 5 概要（続き）
  6. 6 Device Comparison Table
  7. 7 Pin Configuration and Functions
    1.     Pin Functions
  8. 8 Specifications
    1. 8.1 Absolute Maximum Ratings
    2. 8.2 ESD Ratings
    3. 8.3 Recommended Operating Conditions
    4. 8.4 Thermal Information
    5. 8.5 Electrical Characteristics
    6. 8.6 Timing Requirements
    7. 8.7 Switching Characteristics
    8. 8.8 Typical Characteristics
  9. 9 Detailed Description
    1. 9.1 Overview
      1. 9.1.1 VBUS Capacitance
      2. 9.1.2 USB Data Communications
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1  ENSRC
      2. 9.3.2  USB Type-C CC Logic (CC1, CC2)
      3. 9.3.3  USB PD BMC Transmission (CC1, CC2, VTX)
      4. 9.3.4  USB PD BMC Reception (CC1, CC2)
      5. 9.3.5  Discharging (DSCG, VPWR)
        1. 9.3.5.1 Discharging after a Fault (VPWR)
      6. 9.3.6  Configuring Voltage Capabilities (HIPWR)
      7. 9.3.7  Configuring Power Capabilities (PSEL, PCTRL, HIPWR)
      8. 9.3.8  Gate Driver (GDNG, GDNS)
      9. 9.3.9  Fault Monitoring and Protection
        1. 9.3.9.1 Over/Under Voltage (VBUS)
        2. 9.3.9.2 Over-Current Protection (ISNS, VBUS)
        3. 9.3.9.3 System Fault Input (GD, VPWR)
      10. 9.3.10 Voltage Control (CTL1, CTL2,CTL3)
      11. 9.3.11 Sink Attachment Indicator (DVDD)
      12. 9.3.12 Power Supplies (VAUX, VDD, VPWR, DVDD)
      13. 9.3.13 Grounds (AGND, GND)
      14. 9.3.14 Output Power Supply (DVDD)
    4. 9.4 Device Functional Modes
      1. 9.4.1 Sleep Mode
      2. 9.4.2 Checking VBUS at Start Up
  10. 10Application and Implementation
    1. 10.1 Application Information
      1. 10.1.1 System-Level ESD Protection
      2. 10.1.2 Using ENSRC to Enable the Power Supply upon Sink Attachment
      3. 10.1.3 Use of GD Internal Clamp
      4. 10.1.4 Resistor Divider on GD for Programmable Start Up
      5. 10.1.5 Selection of the CTL1, CTL2, and CTL3 Resistors (R(FBL1), R(FBL2), and R(FBL3))
      6. 10.1.6 Voltage Transition Requirements
      7. 10.1.7 VBUS Slew Control using GDNG C(SLEW)
      8. 10.1.8 Tuning OCP using RF and CF
    2. 10.2 Typical Applications
      1. 10.2.1 Typical Application, A/C Power Source (Wall Adapter)
        1. 10.2.1.1 Design Requirements
        2. 10.2.1.2 Detailed Design Procedure
          1. 10.2.1.2.1 Power Pin Bypass Capacitors
          2. 10.2.1.2.2 Non-Configurable Components
          3. 10.2.1.2.3 Configurable Components
        3. 10.2.1.3 Application Curves
      2. 10.2.2 Typical Application, D/C Power Source
        1. 10.2.2.1 Design Requirements
        2. 10.2.2.2 Detailed Design Procedure
          1. 10.2.2.2.1 Power Pin Bypass Capacitors
          2. 10.2.2.2.2 Non-Configurable Components
          3. 10.2.2.2.3 Configurable Components
        3. 10.2.2.3 Application Curves
    3. 10.3 System Examples
      1. 10.3.1 D/C Power Source (Power Hub)
      2. 10.3.2 A/C Power Source (Wall Adapter)
      3. 10.3.3 Dual-Port A/C Power Source (Wall Adaptor)
      4. 10.3.4 D/C Power Source (Power Hub with 3.3 V Rail)
  11. 11Power Supply Recommendations
    1. 11.1 VDD
    2. 11.2 VPWR
  12. 12Layout
    1. 12.1 Port Current Kelvin Sensing
    2. 12.2 Layout Guidelines
      1. 12.2.1 Power Pin Bypass Capacitors
      2. 12.2.2 Supporting Components
    3. 12.3 Layout Example
  13. 13デバイスおよびドキュメントのサポート
    1. 13.1 ドキュメントのサポート
    2. 13.2 ドキュメントの更新通知を受け取る方法
    3. 13.3 コミュニティ・リソース
    4. 13.4 商標
    5. 13.5 静電気放電に関する注意事項
    6. 13.6 Glossary
  14. 14メカニカル、パッケージ、および注文情報

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

12.2.2 Supporting Components

  • C(RX): Place C(RX1) and C(RX2) in line with the CC1 and CC2 traces as shown in Figure 25. These should be placed within one inch from the Type C connector. Minimize stubs and tees from on the trace routes.
  • Q1: Place Q1 in a manner such that power flows uninterrupted from Q1 drain to the Type C connector VBUS connections. Provide adequate copper plane from Q1 drain and source to the interconnecting circuits.
  • RS: Place RS as shown in Figure 72 to facilitate uninterrupted power flow to the Type C connector. Orient RS for optimal Kelvin sense connection/routing back to the TPS25740B. In high current applications where the power dissipation is over 250 mW, provide an adequate copper feed to the pads of RS.
  • RG: Place RG near Q1 as shown in Figure 72. Minimize stray leakage paths as the GDNG sourcing current could be affected.
  • R(SLEW)/C(SLEW): Place R(SLEW) and C(SLEW) near RG as shown in Figure 72.
  • R(DSCG): Place on top of the VBUS copper route and connect to the DSCG pin with a 15 mil trace.
  • RF/CF: When required, place RF and CF as shown in Figure 72 to facilitate the Kelvin sense connection back to the device.
  • C(VBUS)/D(VBUS): Place C(VBUS) and D(VBUS) within one inch of the Type C connector and connect them to VBUS and GND using adequate copper shapes.
  • R(SEL)/R(PCTRL): Place R(SEL) and R(PCTRL) near the device.