JAJSKH0C April   2023  – February 2024 TPS274C65

PRODUCTION DATA  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 Device Comparison Table
  6. 5 Pin Configuration and Functions
    1.     7
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Switching Characteristics
    7. 6.7 SPI Timing Requirements
    8. 6.8 Typical Characteristics
  8. 7 Parameter Measurement Information
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Pin Diagrams
      2. 8.3.2 SPI Mode Operation
        1. 8.3.2.1 Diagnostic Bit Behavior
      3. 8.3.3 Programmable Current Limit
        1. 8.3.3.1 Inrush Current Handling
      4. 8.3.4 DO_EN Feature
      5. 8.3.5 Protection Mechanisms
        1. 8.3.5.1 Overcurrent Protection
        2. 8.3.5.2 Short Circuit Protection
          1. 8.3.5.2.1 VS During Short-to-Ground
        3. 8.3.5.3 Inductive-Load Switching-Off Clamp
        4. 8.3.5.4 Inductive Load Demagnetization
        5. 8.3.5.5 Thermal Shutdown
        6. 8.3.5.6 Undervoltage protection on VS
        7. 8.3.5.7 Undervoltage Lockout on Low Voltage Supply (VDD_UVLO)
        8. 8.3.5.8 Power-Up and Power-Down Behavior
        9. 8.3.5.9 Reverse Current Blocking
      6. 8.3.6 Diagnostic Mechanisms
        1. 8.3.6.1 Current Sense
          1. 8.3.6.1.1 RSNS Value
            1. 8.3.6.1.1.1 SNS Output Filter
        2. 8.3.6.2 Fault Indication
          1. 8.3.6.2.1 Current Limit Behavior
        3. 8.3.6.3 Short-to-Battery and Open-Load Detection
        4. 8.3.6.4 On-State Wire-Break Detection
        5. 8.3.6.5 Off State Wire-Break Detection
        6. 8.3.6.6 ADC
      7. 8.3.7 LED Driver
    4. 8.4 Device Functional Modes
      1. 8.4.1 OFF/POR
      2. 8.4.2 INIT
      3. 8.4.3 Active
    5. 8.5 TPS274C65BS Available Registers List
    6. 8.6 TPS274C65 Registers
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 IEC 61000-4-5 Surge
        2. 9.2.2.2 Loss of GND
        3. 9.2.2.3 Paralleling Channels
      3. 9.2.3 Application Curves
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 ドキュメントの更新通知を受け取る方法
    2. 10.2 サポート・リソース
    3. 10.3 Trademarks
    4. 10.4 静電気放電に関する注意事項
    5. 10.5 用語集
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

9.2.1 Design Requirements

Table 9-1 Recommended External Components
COMPONENT TYPICAL VALUE PURPOSE
RSNS 1 kΩ Translate the sense current into sense voltage.
CSNS 100 pF Low-pass filter for the ADC input.
RILIMx 5 kΩ to 80 kΩ Set current limit threshold, connect from pin to IC GND.
CVin1 4.7 nF to Device GND Filtering of voltage transients (for example, ESD, IEC 61000-4-5) and improved emissions.
CVin2 100 nF to Module GND Stabilize the input supply and filter out low frequency noise.
CVDD 2.2 µF to Module GND Stabilize the VDD supply and limit supply excursions. Needed with either external or internal VDD supplies.
COUT 22 nF Filtering of voltage transients (for example, ESD, RF transients).
ZTVS 36-V TVS Clamp surge voltages at the supply input.
DGND, ZGND Diode + max 10 Ω from Device GND to Module GND Optional for reverse polarity protection - if needed. Series resistor needed for surge events.
RGND 4.7 kΩ Stabilize IC GND in the event of negative output swings.

QRCB

 20-nC FET Optional for Reverse current blocking.
RS 490 Ω Limiting the current flowing through the LEDs.
RF 490 Ω Limiting the current flowing through the LEDs.