JAJSEM6J April   2006  – October 2020 TXB0104

PRODUCTION DATA  

  1. 特長
  2. アプリケーション
  3. 概要
  4. Revision History
  5. Pin Configuration and Functions
  6. Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Electrical Characteristics
    6. 6.6  Timing Requirements: VCCA = 1.2 V
    7. 6.7  Timing Requirements: VCCA = 1.5 V ± 0.1 V
    8. 6.8  Timing Requirements: VCCA = 1.8 V ± 0.15 V
    9. 6.9  Timing Requirements: VCCA = 2.5 V ± 0.2 V
    10. 6.10 Timing Requirements: VCCA = 3.3 V ± 0.3 V
    11. 6.11 Switching Characteristics: VCCA = 1.2 V
    12. 6.12 Switching Characteristics: VCCA = 1.5 V ± 0.1 V
    13. 6.13 Switching Characteristics: VCCA = 1.8 V ± 0.15 V
    14. 6.14 Switching Characteristics: VCCA = 2.5 V ± 0.2 V
    15. 6.15 Switching Characteristics: VCCA = 3.3 V ± 0.3 V
    16. 6.16 Operating Characteristics: VCCA = 1.2 V to 1.5 V, VCCB = 1.5 V to 1.8 V
    17. 6.17 Operating Characteristics: VCCA = 1.8 V to 3.3 V, VCCB = 1.8 V to 5 V
    18. 6.18 Typical Characteristics
  7. Parameter Measurement Information
  8. Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Architecture
      2. 8.3.2 Input Driver Requirements
      3. 8.3.3 Output Load Considerations
      4. 8.3.4 Enable and Disable
      5. 8.3.5 Pullup or Pulldown Resistors on I/O Lines
    4. 8.4 Device Functional Modes
  9. Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
      3. 9.2.3 Application Curves
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12Device and Documentation Support
    1. 12.1 Receiving Notification of Documentation Updates
    2. 12.2 サポート・リソース
    3. 12.3 Trademarks
    4. 12.4 Electrostatic Discharge Caution
    5. 12.5 Glossary
  13. 13Mechanical, Packaging, and Orderable Information

パッケージ・オプション

デバイスごとのパッケージ図は、PDF版データシートをご参照ください。

メカニカル・データ(パッケージ|ピン)
  • D|14
  • RGY|14
  • RUT|12
  • NMN|12
  • YZT|12
  • PW|14
サーマルパッド・メカニカル・データ
発注情報

Parameter Measurement Information

Unless otherwise noted, all input pulses are supplied by generators that have the following characteristics:

  • PRR 10 MHz
  • ZO = 50 W
  • dv/dt ≥ 1 V/ns

Note:

All parameters and waveforms are not applicable to all devices.

GUID-847DD3A6-BD8E-4FAB-8C90-C7BF6AD93DCC-low.gif
The outputs are measured one at a time, with one transition per measurement.
Figure 7-1 Load Circuit For Maximum Data Rate: Pulse Duration,
Propagation Delay Output Rise, And Fall Time Measurement
GUID-F2301C50-1C2B-4336-928C-F66B31AD6BC6-low.gif
The outputs are measured one at a time, with one transition per measurement.
Figure 7-2 Load Circuit For Enable and Disable Time Measurement
Table 7-1 Switch Position For Enable and Disable Time Measurement (See Figure 7-2)
TEST S1
tPZL, tPLZ 2 × VCCO
tPHZ, tPZH Open
GUID-689E817B-6E4F-4465-A1BD-51326D2959FB-low.gif
VCCI is the VCC associated with the input port.
VCCO is theVCC associated with the output port.
tPLH and tPHL are the same as tpd.
The outputs are measured one at a time, with one transition per measurement.
Figure 7-3 Voltage Waveforms Propagation Delay Times
GUID-597EEE48-5419-445A-8242-670C8E29EABC-low.gif Figure 7-4 Voltage Waveforms Pulse Duration