SCPS289B September   2024  – August 2026 TPLD1202

PRODUCTION DATA  

  1.   1
  2.   2
  3.   3
  4. 1 Features
  5. 2 Applications
  6. 3 Description
  7. 4 Pin Configuration and Functions
  8. 5 Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
    4. 5.4  Thermal Information
    5. 5.5  Electrical Characteristics
    6. 5.6  Supply Current Characteristics
    7. 5.7  Switching Characteristics
    8. 5.8  I2C Bus Timing Requirements
    9. 5.9  SPI Timing Requirements
    10. 5.10 Typical Characteristics
  9. 6 Parameter Measurement Information
  10. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  I/O Pins
        1. 7.3.1.1 Input Modes
        2. 7.3.1.2 Output Modes
        3. 7.3.1.3 Pull-Up or Pull-Down Resistors
      2. 7.3.2  Connection Mux
      3. 7.3.3  Configurable Use Logic blocks
        1. 7.3.3.1 2-Bit LUT or D Flip-Flop/Latch macro-cell
          1. 7.3.3.1.1 2-Bit LUT
          2. 7.3.3.1.2 D Flip-Flop/Latch
        2. 7.3.3.2 2-Bit LUT or Pattern Generator macro-cell
          1. 7.3.3.2.1 2-Bit LUT
          2. 7.3.3.2.2 Pattern Generator
        3. 7.3.3.3 3-Bit LUT or D Flip-Flop/Latch With Reset/Set Macro-Cell
          1. 7.3.3.3.1 3-bit LUT
          2. 7.3.3.3.2 D Flip-Flop/Latch with Reset/Set
        4. 7.3.3.4 3-Bit LUT or D Flip-Flop/Latch or Shift Register macro-cell
          1. 7.3.3.4.1 3-bit LUT
          2. 7.3.3.4.2 D Flip-Flop/Latch with Reset/Set
          3. 7.3.3.4.3 8-bit Shift Register
        5. 7.3.3.5 4-Bit LUT or D Flip-Flop/Latch with Reset/Set Macro-Cell
          1. 7.3.3.5.1 4-bit LUT
          2. 7.3.3.5.2 D Flip-Flop/Latch with Reset/Set
      4. 7.3.4  Configurable Logic and Timing Blocks
        1. 7.3.4.1 3-bit LUT
        2. 7.3.4.2 D Flip-Flop/Latch with Reset/Set
        3. 7.3.4.3 8-Bit Counters/Delay Generators (CNT/DLY)
          1. 7.3.4.3.1 Delay Mode
          2. 7.3.4.3.2 Reset Counter Mode
          3. 7.3.4.3.3 One-Shot Mode
          4. 7.3.4.3.4 Frequency Detector Mode
          5. 7.3.4.3.5 Edge Detector Mode
          6. 7.3.4.3.6 Delayed Edge Detector Mode
        4. 7.3.4.4 LUT/DFF + CNT modes
      5. 7.3.5  Programmable Deglitch Filter or Edge Detector
      6. 7.3.6  Deglitch Filter or Edge Detector
      7. 7.3.7  State Machine (SM)
        1. 7.3.7.1 State Machine Inputs
        2. 7.3.7.2 State Machine Outputs
        3. 7.3.7.3 Configuring the State Machine
        4. 7.3.7.4 State Machine Timing Considerations
      8. 7.3.8  8-Bit Counters/Delay Generators/Finite State Machines
      9. 7.3.9  PWM Generators
      10. 7.3.10 Watchdog Timer
      11. 7.3.11 Multi-channel Analog Comparator (McACMP)
      12. 7.3.12 Voltage Reference (VREF)
      13. 7.3.13 Analog Temperature Sensor (TS)
      14. 7.3.14 Oscillators
        1. 7.3.14.1 2kHz or 10kHz Selectable Frequency Oscillator
        2. 7.3.14.2 25MHz Fixed Frequency Oscillator
        3. 7.3.14.3 Oscillator Power Modes
      15. 7.3.15 Serial Communications
        1. 7.3.15.1 I2C Mode
        2. 7.3.15.2 SPI Mode
        3. 7.3.15.3 Virtual I/Os
    4. 7.4 Device Functional Modes
      1. 7.4.1 Power-On Reset
      2. 7.4.2 Power Supply Control Modes
      3. 7.4.3 Protection Features
        1. 7.4.3.1 Device Read/Write Lock
        2. 7.4.3.2 OTP Cyclic Redundancy Check (CRC)
      4. 7.4.4 Programming
        1. 7.4.4.1 Selectable I2C/SPI Interface
        2. 7.4.4.2 One-Time Programmable Memory (OTP) and Programming Procedure
        3. 7.4.4.3 Intel HEX File Format
  11. 8 TPLD1202 Registers
    1. 8.1 TPLD1202_User Registers
    2. 8.2 TPLD1202_Cfg_0 Registers
    3. 8.3 TPLD1202_Cfg_1 Registers
  12. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
        1. 9.2.1.1 Power Considerations
        2. 9.2.1.2 Input Considerations
        3. 9.2.1.3 Output Considerations
      2. 9.2.2 Detailed Design Procedure
      3. 9.2.3 Application Curves
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  13. 10Device and Documentation Support
    1. 10.1 Receiving Notification of Documentation Updates
    2. 10.2 Support Resources
    3. 10.3 Trademarks
    4. 10.4 Electrostatic Discharge Caution
    5. 10.5 Glossary
  14. 11Revision History
  15. 12Mechanical, Packaging, and Orderable Information

6 Parameter Measurement Information

Phase relationships between waveforms are selected arbitrarily. All input pulses are supplied by generators having the following characteristics: PRR ≤ 1MHz, ZO = 50Ω, tt < 5ns.

For clock inputs, fmax is measured when the input duty cycle is 50%.

The outputs are measured one at a time with one input transition per measurement.

TPLD1202 Load Circuit for 3-State Outputs
(1) CL includes probe and test-fixture capacitance.
Figure 6-1 Load Circuit for 3-State Outputs
TPLD1202 Load Circuit for Push-Pull Outputs
(1) CL includes probe and test-fixture capacitance.
Figure 6-3 Load Circuit for Push-Pull Outputs
TPLD1202 Load Circuit for Open-Drain Outputs
(1) CL includes probe and test-fixture capacitance.
Figure 6-2 Load Circuit for Open-Drain Outputs
TPLD1202 Voltage Waveforms, Pulse DurationFigure 6-4 Voltage Waveforms, Pulse Duration
TPLD1202 Voltage Waveforms Propagation Delays
(1) The greater between tPLH and tPHL is the same as tpd.
Figure 6-6 Voltage Waveforms Propagation Delays
TPLD1202 Voltage Waveforms Propagation Delays
(1) The greater between tPLZ and tPZL is the same as tpd.
Figure 6-8 Voltage Waveforms Propagation Delays
TPLD1202 Voltage Waveforms, Setup and Hold TimesFigure 6-5 Voltage Waveforms, Setup and Hold Times
TPLD1202 Voltage Waveforms Propagation DelaysFigure 6-7 Voltage Waveforms Propagation Delays
TPLD1202 Voltage Waveforms, Input and Output Transition Times
(1) The greater between tr and tf is the same as tt.
Figure 6-9 Voltage Waveforms, Input and Output Transition Times
TPLD1202 I2C Interface Load Circuit and Voltage Waveforms
A. CL include probe and jig capacitance.
Figure 6-10 I2C Interface Load Circuit and Voltage Waveforms
TPLD1202 SPI Interface Load Circuit and Voltage Waveforms
A. CL include probe and jig capacitance.
Figure 6-11 SPI Interface Load Circuit and Voltage Waveforms