SCPS289B September   2024  – August 2026 TPLD1202

PRODUCTION DATA  

  1.   1
  2.   2
  3.   3
  4. 1 Features
  5. 2 Applications
  6. 3 Description
  7. 4 Pin Configuration and Functions
  8. 5 Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
    4. 5.4  Thermal Information
    5. 5.5  Electrical Characteristics
    6. 5.6  Supply Current Characteristics
    7. 5.7  Switching Characteristics
    8. 5.8  I2C Bus Timing Requirements
    9. 5.9  SPI Timing Requirements
    10. 5.10 Typical Characteristics
  9. 6 Parameter Measurement Information
  10. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  I/O Pins
        1. 7.3.1.1 Input Modes
        2. 7.3.1.2 Output Modes
        3. 7.3.1.3 Pull-Up or Pull-Down Resistors
      2. 7.3.2  Connection Mux
      3. 7.3.3  Configurable Use Logic blocks
        1. 7.3.3.1 2-Bit LUT or D Flip-Flop/Latch macro-cell
          1. 7.3.3.1.1 2-Bit LUT
          2. 7.3.3.1.2 D Flip-Flop/Latch
        2. 7.3.3.2 2-Bit LUT or Pattern Generator macro-cell
          1. 7.3.3.2.1 2-Bit LUT
          2. 7.3.3.2.2 Pattern Generator
        3. 7.3.3.3 3-Bit LUT or D Flip-Flop/Latch With Reset/Set Macro-Cell
          1. 7.3.3.3.1 3-bit LUT
          2. 7.3.3.3.2 D Flip-Flop/Latch with Reset/Set
        4. 7.3.3.4 3-Bit LUT or D Flip-Flop/Latch or Shift Register macro-cell
          1. 7.3.3.4.1 3-bit LUT
          2. 7.3.3.4.2 D Flip-Flop/Latch with Reset/Set
          3. 7.3.3.4.3 8-bit Shift Register
        5. 7.3.3.5 4-Bit LUT or D Flip-Flop/Latch with Reset/Set Macro-Cell
          1. 7.3.3.5.1 4-bit LUT
          2. 7.3.3.5.2 D Flip-Flop/Latch with Reset/Set
      4. 7.3.4  Configurable Logic and Timing Blocks
        1. 7.3.4.1 3-bit LUT
        2. 7.3.4.2 D Flip-Flop/Latch with Reset/Set
        3. 7.3.4.3 8-Bit Counters/Delay Generators (CNT/DLY)
          1. 7.3.4.3.1 Delay Mode
          2. 7.3.4.3.2 Reset Counter Mode
          3. 7.3.4.3.3 One-Shot Mode
          4. 7.3.4.3.4 Frequency Detector Mode
          5. 7.3.4.3.5 Edge Detector Mode
          6. 7.3.4.3.6 Delayed Edge Detector Mode
        4. 7.3.4.4 LUT/DFF + CNT modes
      5. 7.3.5  Programmable Deglitch Filter or Edge Detector
      6. 7.3.6  Deglitch Filter or Edge Detector
      7. 7.3.7  State Machine (SM)
        1. 7.3.7.1 State Machine Inputs
        2. 7.3.7.2 State Machine Outputs
        3. 7.3.7.3 Configuring the State Machine
        4. 7.3.7.4 State Machine Timing Considerations
      8. 7.3.8  8-Bit Counters/Delay Generators/Finite State Machines
      9. 7.3.9  PWM Generators
      10. 7.3.10 Watchdog Timer
      11. 7.3.11 Multi-channel Analog Comparator (McACMP)
      12. 7.3.12 Voltage Reference (VREF)
      13. 7.3.13 Analog Temperature Sensor (TS)
      14. 7.3.14 Oscillators
        1. 7.3.14.1 2kHz or 10kHz Selectable Frequency Oscillator
        2. 7.3.14.2 25MHz Fixed Frequency Oscillator
        3. 7.3.14.3 Oscillator Power Modes
      15. 7.3.15 Serial Communications
        1. 7.3.15.1 I2C Mode
        2. 7.3.15.2 SPI Mode
        3. 7.3.15.3 Virtual I/Os
    4. 7.4 Device Functional Modes
      1. 7.4.1 Power-On Reset
      2. 7.4.2 Power Supply Control Modes
      3. 7.4.3 Protection Features
        1. 7.4.3.1 Device Read/Write Lock
        2. 7.4.3.2 OTP Cyclic Redundancy Check (CRC)
      4. 7.4.4 Programming
        1. 7.4.4.1 Selectable I2C/SPI Interface
        2. 7.4.4.2 One-Time Programmable Memory (OTP) and Programming Procedure
        3. 7.4.4.3 Intel HEX File Format
  11. 8 TPLD1202 Registers
    1. 8.1 TPLD1202_User Registers
    2. 8.2 TPLD1202_Cfg_0 Registers
    3. 8.3 TPLD1202_Cfg_1 Registers
  12. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
        1. 9.2.1.1 Power Considerations
        2. 9.2.1.2 Input Considerations
        3. 9.2.1.3 Output Considerations
      2. 9.2.2 Detailed Design Procedure
      3. 9.2.3 Application Curves
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  13. 10Device and Documentation Support
    1. 10.1 Receiving Notification of Documentation Updates
    2. 10.2 Support Resources
    3. 10.3 Trademarks
    4. 10.4 Electrostatic Discharge Caution
    5. 10.5 Glossary
  14. 11Revision History
  15. 12Mechanical, Packaging, and Orderable Information

Pull-Up or Pull-Down Resistors

All I/O pins have the option of user-selectable resistors that can be connected to the pin structure. The selectable values on these resistors are 10kΩ, 100kΩ and 1MΩ. The internal resistors can be configured as either pull-up or pull-down. When designing in InterConnect Studio, any pin left unused in a design are configured with a 1MΩ pull-down by default. Furthermore, following a power-on event, all ports are in a Hi-Z state until the power-on reset sequence has completed.

Table 7-1 Pin Configuration Options

GPIO

IO selectionOEIO optionsResistorResistor value (Ω)
IN0Pin not used——Pull-Down1M
Digital input0

Digital in without Schmitt trigger

Digital in with Schmitt trigger

Low-voltage digital input

Floating—
Pull-Down

Pull-Up

10k

100k

1M

IO1, IO2Pin not used——Pull-Down1M
Digital input0

Digital in without Schmitt trigger

Digital in with Schmitt trigger

Low-voltage digital input

Floating—
Pull-Down

Pull-Up

10k

100k

1M

Digital output1Push-pull (1X, 2X)Open-drain NMOS (1X, 4X)Floating—
Pull-Down

Pull-Up

10k

100k

1M

IO3, IO4, IO8Pin not used——Pull-Down1M
Digital input0

Digital in without Schmitt trigger

Digital in with Schmitt trigger

Low-voltage digital input

Floating—
Pull-Down

Pull-Up

10k

100k

1M

Digital output1Push-pull (1X, 2X)Floating—

Open-drain NMOS (1X, 2X)

3-state output (1X, 2X)

Pull-Down

Pull-Up

10k

100k

1M

Digital input/output0

Digital in without Schmitt trigger

Digital in with Schmitt trigger

Low-voltage digital input

Analog input

Floating—
Pull-Down

Pull-Up

10k

100k

1M

1Push-pull (1X, 2X)

Open-drain NMOS (1X, 2X)

Analog input/output—Analog input/outputFloating—
Pull-Down

Pull-Up

10k

100k

1M

IO5, IO6, IO7Pin not used——Pull-Down1M
Digital input0

Digital in without Schmitt trigger

Digital in with Schmitt trigger

Low-voltage digital input

Floating—
Pull-Down

Pull-Up

10k

100k

1M

Digital output1Push-pull (1X, 2X)Floating—

Open-drain NMOS (1X, 2X)

Pull-Down

Pull-Up

10k

100k

1M

Analog input/output—Analog input/outputFloating—
Pull-Down

Pull-Up

10k

100k

1M

IO9Pin not used——Pull-Down1M
Digital input0

Digital in without Schmitt trigger

Digital in with Schmitt trigger

Low-voltage digital input

Floating—
Pull-Down

Pull-Up

10k

100k

1M

Digital output1Push-pull (1X, 2X)Floating—

Open-drain NMOS (1X, 2X)

3-state output (1X, 2X)

Pull-Down

Pull-Up

10k

100k

1M

Digital input/output0

Digital in without Schmitt trigger

Digital in with Schmitt trigger

Low-voltage digital input

Floating—
Pull-Down

Pull-Up

10k

100k

1M

1Push-pull (1X, 2X)

Open-drain NMOS (1X, 2X)

Note:

When using an IO with output-enable (OE) controlled from the CMX configured as a Digital output with 3-state output, TI recommends configuring the input mode to 0b11 (Analog IO or Reserved).