SLVSHH0 June   2026 TPS61290

PRODMIX  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Comparison Table
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 I2C Interface Timing Requirements
    7. 6.7 Typical Characteristics
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Output Voltage Setting
      2. 7.3.2 Switching Frequency and Spread Spectrum Function
    4. 7.4 Device Functional Modes
      1. 7.4.1  Enable and Start-Up
      2. 7.4.2  Operation Mode Setting
      3. 7.4.3  Bypass Mode
      4. 7.4.4  Boost Control Operation
      5. 7.4.5  Auto PFM Mode
      6. 7.4.6  Forced PWM Mode
      7. 7.4.7  Output Discharge
      8. 7.4.8  Undervoltage Lockout
      9. 7.4.9  Current Limit Operation
      10. 7.4.10 Output Short-to-Ground Protection
      11. 7.4.11 Thermal Shutdown
      12. 7.4.12 Power-Good Indication Status
    5. 7.5 Programming
      1. 7.5.1 Data Validity
      2. 7.5.2 START and STOP Conditions
      3. 7.5.3 Byte Format
      4. 7.5.4 Acknowledge (ACK) and Not Acknowledge (NACK)
      5. 7.5.5 Target Address and Data Direction Bit
      6. 7.5.6 Single Read and Write
      7. 7.5.7 Multi-Read and Multi-Write
  9. 8 Register Maps
    1. 8.1 DeviceID Register
    2. 8.2 CONFIG Register
    3. 8.3 VOUTFLOORSET Register
    4. 8.4 ILIMBSTSET Register
    5. 8.5 VOUTROOFSET Register
    6. 8.6 STATUS Register
    7. 8.7 ILIMPTSET Register
    8. 8.8 BSTLOOP Register
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 TPS61290x With 2.5V – 4.35V VIN, 3.4V VOUT, 6A Output Current
        1. 9.2.1.1 Design Requirements
        2. 9.2.1.2 Detailed Design Procedure
          1. 9.2.1.2.1 Inductor Selection
          2. 9.2.1.2.2 Output Capacitor
          3. 9.2.1.2.3 Input Capacitor
          4. 9.2.1.2.4 Checking Loop Stability
        3. 9.2.1.3 Application Curves
      2. 9.2.2 TPS61290x With 2.5V – 4.85V VIN, 5.0V VOUT, 4A Output Current
        1. 9.2.2.1 Design Requirements
        2. 9.2.2.2 Detailed Design Procedure
        3. 9.2.2.3 Application Curves
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
      3. 9.4.3 Thermal Information
  11. 10Device and Documentation Support
    1. 10.1 Device Support
      1. 10.1.1 Third-Party Products Disclaimer
    2. 10.2 Receiving Notification of Documentation Updates
    3. 10.3 Support Resources
    4. 10.4 Trademarks
    5. 10.5 Electrostatic Discharge Caution
    6. 10.6 Glossary
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information
    1.     81

9.2.2.1 Design Requirements

Table 9-4 Design Parameters
REFERENCEDESCRIPTIONSAMPLE VALUES
VINInput voltage range2.5V – 4.85V
VOUTOutput voltage range at boost modeVOUT = 5.0V
Output voltage range bypass modeVOUT = VIN – IOUT × RDS(ON)_BYP
IOUTOutput current4A (maximum)
Table 9-5 Component List
REFERENCEDESCRIPTIONPART NUMBER, MANUFACTURER(1)
CIN22μF, 10V, 0603, X5R ceramicGRM187R61A226ME15D
COUT4 × 22μF, 10V, 0603, X5R ceramic4 × GRM187R61A226ME15D
L220nH, 5mΩ, 4.0mm × 4.0mm × 1.2mmXGL4012-221MEC

In this application, TI recommends to use inductors from the following different suppliers with the TPS61290x converters.

Table 9-6 List of Inductors
SERIESL (nH)DIMENSIONS (in mm)DC INPUT CURRENT LIMIT SETTINGMANUFACTURER
XGL4012-2212204.0 × 4.0 × 1.2 maximum height≤14.4ACoilcraft
XGL4012-2512504.0 × 4.0 × 1.2 maximum height≤13.3ACoilcraft
XGL3512-2012003.5 × 3.2 × 1.2 maximum height≤10.0ACoilcraft
XGL3520-2012003.5 × 3.2 × 2.0 maximum height≤11.4ACoilcraft
XGL3520-3013003.5 × 3.2 × 2.0 maximum height≤9.7ACoilcraft