SLVSI75 May   2026 DRV8218

ADVANCE INFORMATION  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Comparison
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Transient Current Capability
    7. 6.7 Timing Diagrams
    8. 6.8 Typical Characteristics
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 External Components
    4. 7.4 Feature Description
      1. 7.4.1 Control Modes
        1. 7.4.1.1 PWM Control Mode (MODE = 0)
        2. 7.4.1.2 PH/EN Control Mode (MODE = 1)
        3. 7.4.1.3 Independent Half-Bridge Control Mode (MODE = Hi-Z)
      2. 7.4.2 Pin Diagrams
        1. 7.4.2.1 Logic-Level Inputs
        2. 7.4.2.2 Tri-Level Input
      3. 7.4.3 Protection Circuits
        1. 7.4.3.1 Supply Undervoltage Lockout (UVLO)
        2. 7.4.3.2 OUTx Overcurrent Protection (OCP)
        3. 7.4.3.3 Thermal Shutdown (TSD)
    5. 7.5 Device Functional Modes
      1. 7.5.1 Active Mode
      2. 7.5.2 Low-Power Sleep Mode
      3. 7.5.3 Fault Mode
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Full-Bridge Driving
        1. 8.2.1.1 Supply Voltage
        2. 8.2.1.2 Control Interface - Full Bridge
        3. 8.2.1.3 Low-Power Operation
        4. 8.2.1.4 Application Curves
      2. 8.2.2 Half-Bridge Driving
        1. 8.2.2.1 Control Interface
        2. 8.2.2.2 Low-Power Operation
        3. 8.2.2.3 Application Curves
      3. 8.2.3 Parallel Multiple Drivers
      4. 8.2.4 Dual-Coil Relay Driving
        1. 8.2.4.1 Control Interface
        2. 8.2.4.2 Low-Power Operation
        3. 8.2.4.3 Application Curves
      5. 8.2.5 Current Sense
        1. 8.2.5.1 Design Requirements
        2. 8.2.5.2 Detailed Design Procedure
          1. 8.2.5.2.1 Shunt Resistor Sizing
          2. 8.2.5.2.2 RC Filter
    3. 8.3 Current Capability and Thermal Performance
      1. 8.3.1 Power Dissipation and Output Current Capability
    4. 8.4 Power Supply Recommendations
      1. 8.4.1 Bulk Capacitance
    5. 8.5 Layout
      1. 8.5.1 Layout Guidelines
      2. 8.5.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Documentation Support
      1. 9.1.1 Related Documentation
    2. 9.2 Receiving Notification of Documentation Updates
    3. 9.3 Support Resources
    4. 9.4 Trademarks
    5. 9.5 Electrostatic Discharge Caution
    6. 9.6 Glossary
  11. 10Mechanical, Packaging, and Orderable Information

8.2.1.4 Application Curves

DRV8218 PWM driving for a motor with 50% duty cycle, INx and OUTx voltages
A.
Channel 1 = IN1Channel 2 = IN2Channel 3 = OUT1
Channel 4 = OUT2
Figure 8-4 PWM driving for a motor with 50% duty cycle, INx and OUTx voltages
DRV8218 PWM driving for a single-coil latching relay with driving profile FORWARD → COAST → REVERSE → COAST
A.
Channel 1 = IN1Channel 2 = IN2Channel 3 = VOUT1
Channel 4 = VOUT2Channel 6 = Relay SwitchChannel 7 = Relay Coil Current
Figure 8-6 PWM driving for a single-coil latching relay with driving profile FORWARD → COAST → REVERSE → COAST
DRV8218 PWM driving for a motor with 50% duty cycle, signals and motor current
A.
Channel 1 = IN1Channel 2 = Motor CurrentChannel 3 = OUT1
Channel 4 = OUT2
Figure 8-5 PWM driving for a motor with 50% duty cycle, signals and motor current
DRV8218 PWM driving for a single-coil latching relay with driving profile FORWARD → BRAKE → REVERSE → BRAKE
A.
Channel 1 = IN1Channel 2 = IN2Channel 3 = VOUT1
Channel 4 = VOUT2Channel 6 = Relay SwitchChannel 7 = Relay Coil Current
Figure 8-7 PWM driving for a single-coil latching relay with driving profile FORWARD → BRAKE → REVERSE → BRAKE