TIDUEY6 April   2021

 

  1.   Description
  2.   Resources
  3.   Features
  4.   Applications
  5.   5
  6. 1System Description
  7. 2System Overview
    1. 2.1 Block Diagram
    2. 2.2 Design Considerations
    3. 2.3 Highlighted Products
      1. 2.3.1 C2000 MCU F2838x
      2. 2.3.2 UCC5870-Q1 Gate Driver
  8. 3Hardware, Software, Testing Requirements, and Test Results
    1. 3.1 Hardware Requirements
      1. 3.1.1 Hardware Overview
        1. 3.1.1.1 Control Module
          1. 3.1.1.1.1 Control Mother Board
            1. 3.1.1.1.1.1 Inverter Safing - UCC5870 ASC and Fault Control
            2. 3.1.1.1.1.2 DC-DC Safing
            3. 3.1.1.1.1.3 DC-DC Converter Secondary PWM Selection
            4. 3.1.1.1.1.4 Blower Fan Control
            5. 3.1.1.1.1.5 Voltage Monitor
            6. 3.1.1.1.1.6 Resolver Interface Control
            7. 3.1.1.1.1.7 Test Points on Control Module
            8. 3.1.1.1.1.8 General Purpose Ports
            9. 3.1.1.1.1.9 Connectors and Headers on Control Mother Board
          2. 3.1.1.1.2 Power Supplies
            1. 3.1.1.1.2.1 Power Supply 5V /5A
            2. 3.1.1.1.2.2 Power Supply 12-V/1-A
            3. 3.1.1.1.2.3 Power Supply 15-V/0.5-A
          3. 3.1.1.1.3 TCAN4550 module
          4. 3.1.1.1.4 Dual TCAN Module
          5. 3.1.1.1.5 Analog Back End Module
          6. 3.1.1.1.6 Resolver Analog Front End Module
        2. 3.1.1.2 Inverter Module
          1. 3.1.1.2.1 Inverter Mother Board
            1. 3.1.1.2.1.1 Connectors and Headers on Inverter Mother Board
            2. 3.1.1.2.1.2 Jumper and Test Points on Inverter Module
          2. 3.1.1.2.2 Inverter Gate Driver Module
            1. 3.1.1.2.2.1 Inverter Gate Drive Power Supply Module
          3. 3.1.1.2.3 Inverter Current Sense Module
          4. 3.1.1.2.4 Inverter Voltage Sense Module
        3. 3.1.1.3 DC-DC Bidirectional Converter Module
          1. 3.1.1.3.1 DC-DC Converter Mother Board
          2. 3.1.1.3.2 DC-DC Gate Driver Module
    2. 3.2 Resource Mapping
    3. 3.3 Test Setup
    4. 3.4 Test Results
  9. 4General Texas Instruments High Voltage Evaluation (TI HV EVM) User Safety Guidelines
  10. 5Design and Documentation Support
    1. 5.1 Design Files
      1. 5.1.1 Schematics
      2. 5.1.2 BOM
    2. 5.2 Software
    3. 5.3 Documentation Support
    4. 5.4 Support Resources
    5. 5.5 Trademarks
  11. 6About the Author
Analog Back End Module

Analog back end module acts as a back end analog reconstruction module for the differential feedback signals received from the traction inverter module and DC-DC converter module. It is designed using TLV6001 and OPA2350 and other standard linear parts. The module is shown in Figure 3-17.

GUID-20210303-CA0I-0CTN-MDKC-33TDGKR27HP9-low.jpg Figure 3-17 Analog Back End Module

It is mounted on control mother board headers J16 and J27. Basically this module reconstructs the phase current and DC bus voltage signals of the traction inverter and DC-DC converter into low voltage analog signals. These are fed as ADC inputs for control and safety MCUs in the mother board. Besides, the module also provides a digital status feedback for absolute over current, where the limit can be set by resistors R19, R20, R21 and R22 in this module. A digital status feedback for over voltage is also provided, where the limit is set by resistors R14 and R17. There is also over temperature sensing circuit but is re-purposed to measure the DC-DC converter voltage, and its limit protection is ignored. The limit crossing status are latched and is left for the MCUs to clear them per user choice.