TIDUEY6 April   2021

 

  1.   Description
  2.   Resources
  3.   Features
  4.   Applications
  5.   5
  6. 1System Description
  7. 2System Overview
    1. 2.1 Block Diagram
    2. 2.2 Design Considerations
    3. 2.3 Highlighted Products
      1. 2.3.1 C2000 MCU F2838x
      2. 2.3.2 UCC5870-Q1 Gate Driver
  8. 3Hardware, Software, Testing Requirements, and Test Results
    1. 3.1 Hardware Requirements
      1. 3.1.1 Hardware Overview
        1. 3.1.1.1 Control Module
          1. 3.1.1.1.1 Control Mother Board
            1. 3.1.1.1.1.1 Inverter Safing - UCC5870 ASC and Fault Control
            2. 3.1.1.1.1.2 DC-DC Safing
            3. 3.1.1.1.1.3 DC-DC Converter Secondary PWM Selection
            4. 3.1.1.1.1.4 Blower Fan Control
            5. 3.1.1.1.1.5 Voltage Monitor
            6. 3.1.1.1.1.6 Resolver Interface Control
            7. 3.1.1.1.1.7 Test Points on Control Module
            8. 3.1.1.1.1.8 General Purpose Ports
            9. 3.1.1.1.1.9 Connectors and Headers on Control Mother Board
          2. 3.1.1.1.2 Power Supplies
            1. 3.1.1.1.2.1 Power Supply 5V /5A
            2. 3.1.1.1.2.2 Power Supply 12-V/1-A
            3. 3.1.1.1.2.3 Power Supply 15-V/0.5-A
          3. 3.1.1.1.3 TCAN4550 module
          4. 3.1.1.1.4 Dual TCAN Module
          5. 3.1.1.1.5 Analog Back End Module
          6. 3.1.1.1.6 Resolver Analog Front End Module
        2. 3.1.1.2 Inverter Module
          1. 3.1.1.2.1 Inverter Mother Board
            1. 3.1.1.2.1.1 Connectors and Headers on Inverter Mother Board
            2. 3.1.1.2.1.2 Jumper and Test Points on Inverter Module
          2. 3.1.1.2.2 Inverter Gate Driver Module
            1. 3.1.1.2.2.1 Inverter Gate Drive Power Supply Module
          3. 3.1.1.2.3 Inverter Current Sense Module
          4. 3.1.1.2.4 Inverter Voltage Sense Module
        3. 3.1.1.3 DC-DC Bidirectional Converter Module
          1. 3.1.1.3.1 DC-DC Converter Mother Board
          2. 3.1.1.3.2 DC-DC Gate Driver Module
    2. 3.2 Resource Mapping
    3. 3.3 Test Setup
    4. 3.4 Test Results
  9. 4General Texas Instruments High Voltage Evaluation (TI HV EVM) User Safety Guidelines
  10. 5Design and Documentation Support
    1. 5.1 Design Files
      1. 5.1.1 Schematics
      2. 5.1.2 BOM
    2. 5.2 Software
    3. 5.3 Documentation Support
    4. 5.4 Support Resources
    5. 5.5 Trademarks
  11. 6About the Author
3.1.1.1.2.2 Power Supply 12-V/1-A

This is a compact SEPIC power module based on LM3481-Q1. The design is based off TI user guide LM3481 SEPIC Evaluation Board. Detailed design information is available in this user guide. The layout of this module is customized to fit the requirements of EV traction reference design and is shown in Figure 3-13.

GUID-20210303-CA0I-M2NL-ZGHJ-DFV81GCM5LJG-low.jpg Figure 3-13 Vbat to 12-V/1-A Power Supply Module

This module mounts on mother board connectors J29 and J30, with its component side facing the inverter connectors. This will feed the gate driver circuits of DC-DC converter and is made available through connector J7 of mother board.