The OPA2690 represents a major step forward in unity-gain stable, voltage-feedback op amps. A new internal architecture provides slew rate and full-power bandwidth previously found only in wideband, current-feedback op amps. A new output stage architecture delivers high currents with a minimal headroom requirement. These give exceptional single-supply operation. Using a single +5V supply, the OPA2690 can deliver a 1V to 4V output swing with over 120mA drive current and 150MHz bandwidth. This combination of features makes the OPA2690 an ideal RGB line driver or single-supply Analog-to-Digital Converter (ADC) input driver.
The low 5.5mA/ch supply current of the OPA2690 is precisely trimmed at +25°C. This trim, along with low temperature drift, provides lower maximum supply current than competing products. System power may be reduced further using the optional disable control pin. Leaving this disable pin open, or holding it HIGH, will operate the OPA2690I-14D normally. If pulled LOW, the OPA2690I-14D supply current drops to less than 200µA/ch while the output goes to a high-impedance state.
| Top-Dokumentation | Typ | Titel | Format-Optionen | Datum |
|---|---|---|---|---|
| * | Data sheet | Dual, Wideband, Voltage-Feedback Operational Amplifier with Disable datasheet (Rev. G) | 04 Mär 2010 | |
| E-book | The Signal e-book: A compendium of blog posts on op amp design topics | 28 Mär 2017 | ||
| Application note | Design for a Wideband Differential Transimpedance DAC Output (Rev. A) | 17 Okt 2016 | ||
| Application note | RLC Filter Design for ADC Interface Applications (Rev. A) | 13 Mai 2015 | ||
| User guide | DEM-OPA-SO-2A User's Guide (Rev. B) | 30 Apr 2010 | ||
| Application note | Wireline Data Transmission and Reception | 27 Jan 2010 | ||
| User guide | DEM-OPA-SO-2D User's Guide (Rev. A) | 25 Mai 2006 | ||
| Application note | Noise Analysis for High Speed Op Amps (Rev. A) | 17 Jan 2005 | ||
| Application note | ADS5500, OPA695: PC Board Layout for Low Distortion High-Speed ADC Drivers | 22 Apr 2004 | ||
| Application note | Measuring Board Parasitics in High-Speed Analog Design | 07 Jul 2003 |
Weitere Bedingungen oder erforderliche Ressourcen enthält gegebenenfalls die Detailseite, die Sie durch Klicken auf einen der unten stehenden Titel erreichen.
The DEM-OPA-SO-2A demonstration evaluation module helps designers evaluate the operation and performance of TI dual-channel, high-speed, wideband operational amplifiers. This unpopulated printed-circuit board (PCB) is compatible with products offered in the 8-lead SOIC (D) package.
For more (...)
The analog engineer’s calculator is designed to speed up many of the repetitive calculations that analog circuit design engineers use on a regular basis. This PC-based tool provides a graphical interface with a list of various common calculations ranging from setting operational-amplifier (...)
| Gehäuse | Pins | CAD-Symbole, Footprints und 3D-Modelle |
|---|---|---|
| SOIC (D) | 14 | Ultra Librarian |
| SOIC (D) | 8 | Ultra Librarian |
Inhalte werden ohne Gewähr von TI und der Community bereitgestellt. Sie stellen keine Spezifikationen von TI dar. Siehe Nutzungsbedingungen.
Bei Fragen zu den Themen Qualität, Gehäuse oder Bestellung von TI-Produkten siehe TI-Support.
Analog Engineer's Calc Installer
General calculator tool for analog design support.