Inicio Amplificadores Amplificadores operacionales (op amps) Amplificadores operacionales de alta velocidad (GBW ≥ 50 MHz)

OPA2690

ACTIVO

Amplificador operacional doble de banda ancha con retroalimentación de voltaje y deshabilitación

Detalles del producto

Architecture Voltage FB Number of channels 2 Total supply voltage (+5 V = 5, ±5 V = 10) (min) (V) 5 Total supply voltage (+5 V = 5, ±5 V = 10) (max) (V) 12 GBW (typ) (MHz) 500 BW at Acl (MHz) 500 Acl, min spec gain (V/V) 1 Slew rate (typ) (V/µs) 1800 Vn at flatband (typ) (nV√Hz) 5.5 Vn at 1 kHz (typ) (nV√Hz) 5.5 Iq per channel (typ) (mA) 5.5 Vos (offset voltage at 25°C) (max) (mV) 4.5 Rail-to-rail No Features Shutdown Rating Catalog Operating temperature range (°C) -40 to 85 CMRR (typ) (dB) 65 Input bias current (max) (pA) 11000000 Offset drift (typ) (µV/°C) 12 Iout (typ) (mA) 190 2nd harmonic (dBc) 68 3rd harmonic (dBc) 70 Frequency of harmonic distortion measurement (MHz) 5
Architecture Voltage FB Number of channels 2 Total supply voltage (+5 V = 5, ±5 V = 10) (min) (V) 5 Total supply voltage (+5 V = 5, ±5 V = 10) (max) (V) 12 GBW (typ) (MHz) 500 BW at Acl (MHz) 500 Acl, min spec gain (V/V) 1 Slew rate (typ) (V/µs) 1800 Vn at flatband (typ) (nV√Hz) 5.5 Vn at 1 kHz (typ) (nV√Hz) 5.5 Iq per channel (typ) (mA) 5.5 Vos (offset voltage at 25°C) (max) (mV) 4.5 Rail-to-rail No Features Shutdown Rating Catalog Operating temperature range (°C) -40 to 85 CMRR (typ) (dB) 65 Input bias current (max) (pA) 11000000 Offset drift (typ) (µV/°C) 12 Iout (typ) (mA) 190 2nd harmonic (dBc) 68 3rd harmonic (dBc) 70 Frequency of harmonic distortion measurement (MHz) 5
SOIC (D) 14 51.9 mm² (8.65 mm × 6 mm) SOIC (D) 8 29.4 mm² (4.9 mm × 6 mm)
  • FLEXIBLE SUPPLY RANGE:
    +5V to +12V Single Supply
    ±2.5V to ±6V Dual Supply
  • WIDEBAND +5V OPERATION: 220MHz (G = 2)
  • HIGH OUTPUT CURRENT: 190mA
  • OUTPUT VOLTAGE SWING: ±4.0V
  • HIGH SLEW RATE: 1800V/µs
  • LOW SUPPLY CURRENT: 5.5mA/ch
  • LOW DISABLE CURRENT: 100µA/ch
  • APPLICATIONS
    • VIDEO LINE DRIVING
    • xDSL LINE DRIVER/RECEIVER
    • HIGH-SPEED IMAGING CHANNELS
    • ADC BUFFERS
    • PORTABLE INSTRUMENTS
    • TRANSIMPEDANCE AMPLIFIERS
    • ACTIVE FILTERS
  • FLEXIBLE SUPPLY RANGE:
    +5V to +12V Single Supply
    ±2.5V to ±6V Dual Supply
  • WIDEBAND +5V OPERATION: 220MHz (G = 2)
  • HIGH OUTPUT CURRENT: 190mA
  • OUTPUT VOLTAGE SWING: ±4.0V
  • HIGH SLEW RATE: 1800V/µs
  • LOW SUPPLY CURRENT: 5.5mA/ch
  • LOW DISABLE CURRENT: 100µA/ch
  • APPLICATIONS
    • VIDEO LINE DRIVING
    • xDSL LINE DRIVER/RECEIVER
    • HIGH-SPEED IMAGING CHANNELS
    • ADC BUFFERS
    • PORTABLE INSTRUMENTS
    • TRANSIMPEDANCE AMPLIFIERS
    • ACTIVE FILTERS

The OPA2690 represents a major step forward in unity-gain stable, voltage-feedback op amps. A new internal architecture provides slew rate and full-power bandwidth previously found only in wideband, current-feedback op amps. A new output stage architecture delivers high currents with a minimal headroom requirement. These give exceptional single-supply operation. Using a single +5V supply, the OPA2690 can deliver a 1V to 4V output swing with over 120mA drive current and 150MHz bandwidth. This combination of features makes the OPA2690 an ideal RGB line driver or single-supply Analog-to-Digital Converter (ADC) input driver.

The low 5.5mA/ch supply current of the OPA2690 is precisely trimmed at +25°C. This trim, along with low temperature drift, provides lower maximum supply current than competing products. System power may be reduced further using the optional disable control pin. Leaving this disable pin open, or holding it HIGH, will operate the OPA2690I-14D normally. If pulled LOW, the OPA2690I-14D supply current drops to less than 200µA/ch while the output goes to a high-impedance state.

The OPA2690 represents a major step forward in unity-gain stable, voltage-feedback op amps. A new internal architecture provides slew rate and full-power bandwidth previously found only in wideband, current-feedback op amps. A new output stage architecture delivers high currents with a minimal headroom requirement. These give exceptional single-supply operation. Using a single +5V supply, the OPA2690 can deliver a 1V to 4V output swing with over 120mA drive current and 150MHz bandwidth. This combination of features makes the OPA2690 an ideal RGB line driver or single-supply Analog-to-Digital Converter (ADC) input driver.

The low 5.5mA/ch supply current of the OPA2690 is precisely trimmed at +25°C. This trim, along with low temperature drift, provides lower maximum supply current than competing products. System power may be reduced further using the optional disable control pin. Leaving this disable pin open, or holding it HIGH, will operate the OPA2690I-14D normally. If pulled LOW, the OPA2690I-14D supply current drops to less than 200µA/ch while the output goes to a high-impedance state.

Descargar Ver vídeo con transcripción Video

Productos similares que pueden interesarle

open-in-new Comparar alternativas
Misma funcionalidad con diferente configuración de pines que el dispositivo comparado
LMH6626 ACTIVO Amplificador operacional simple/doble de banda ancha y ruido ultrabajo Decompensated (>10V/V), lower noise(1 nV/rtHz), and lower offset (0.5 mV)

Documentación técnica

No se encontraron resultados. Borre su búsqueda y vuelva a intentarlo.
Ver todo 10
Documentación principal Tipo Título Opciones de formato Descargar la versión más reciente en inglés Fecha
* Hoja de datos Dual, Wideband, Voltage-Feedback Operational Amplifier with Disable datasheet (Rev. G) 4/03/2010
Libro electrónico The Signal e-book: A compendium of blog posts on op amp design topics PDF | HTML 28/03/2017
Nota sobre la aplicación Design for a Wideband Differential Transimpedance DAC Output (Rev. A) 17/10/2016
Nota sobre la aplicación RLC Filter Design for ADC Interface Applications (Rev. A) 13/05/2015
Guía del usuario DEM-OPA-SO-2A User's Guide (Rev. B) 30/04/2010
Nota sobre la aplicación Wireline Data Transmission and Reception 27/01/2010
Guía del usuario DEM-OPA-SO-2D User's Guide (Rev. A) 25/05/2006
Nota sobre la aplicación Noise Analysis for High Speed Op Amps (Rev. A) 17/01/2005
Nota sobre la aplicación ADS5500, OPA695: PC Board Layout for Low Distortion High-Speed ADC Drivers 22/04/2004
Nota sobre la aplicación Measuring Board Parasitics in High-Speed Analog Design 7/07/2003

Diseño y desarrollo

Para conocer los términos adicionales o los recursos necesarios, haga clic en cualquier título de abajo para ver la página de detalles cuando esté disponible.

Placa de evaluación

DEM-OPA-SO-2A — Módulo de evaluación de amplificador operacional doble para encapsulado SO-8

The DEM-OPA-SO-2A demonstration evaluation module helps designers evaluate the operation and performance of TI dual-channel, high-speed, wideband operational amplifiers. This unpopulated printed-circuit board (PCB) is compatible with products offered in the 8-lead SOIC (D) package.

For more (...)

Productos y hardware compatibles
En inventario
Límite:
??asset.out-of-stock-ti_es_MX??
No disponible
Placa de evaluación

DEM-OPA-SO-2D — Módulo de evaluación de amplificador operacional doble para encapsulado SO-14

El dispositivo de demostración DEM-OPA-SO-2D es una placa de circuito impreso (PCB) genérica y sin componentes, diseñada para evaluar el funcionamiento y el rendimiento de los amplificadores operacionales dobles de alta velocidad de TI en encapsulados SO-14 (DDB), con función de desactivación.

Productos y hardware compatibles
En inventario
Límite:
??asset.out-of-stock-ti_es_MX??
No disponible
Modelo de simulación

OPA2690 PSpice Model (Rev. A)

SBOM521A.ZIP (175 KB) - Modelo PSpice
Productos y hardware compatibles
Modelo de simulación

OPA2690 TINA-TI Reference Design (Rev. A)

SBOM522A.TSC (2085 KB) - Diseño de referencia TINA-TI
Productos y hardware compatibles
Modelo de simulación

OPA2690 TINA-TI Spice Model (Rev. A)

SBOM520A.ZIP (6 KB) - Modelo TINA-TI Spice
Productos y hardware compatibles
Herramienta de cálculo

ANALOG-ENGINEER-CALC — PC software analog engineer's calculator

La calculadora del ingeniero analógico está diseñada para acelerar muchos de los cálculos repetitivos que los ingenieros de diseño de circuitos analógicos utilizan de forma habitual. Esta herramienta para PC proporciona una interfaz gráfica con una lista de varios cálculos comunes que van desde el (...)

Productos y hardware compatibles
Encapsulado Pines Símbolos CAD, huellas y modelos 3D
SOIC (D) 14 Ultra Librarian
SOIC (D) 8 Ultra Librarian

Pedidos y calidad

Soporte y capacitación

Foros de TI E2E™ con asistencia técnica de los ingenieros de TI

El contenido lo proporcionan “tal como está” TI y los colaboradores de la comunidad y no constituye especificaciones de TI. Consulte los términos de uso.

Si tiene alguna pregunta sobre calidad, encapsulados o pedido de productos de TI, consulte el servicio de asistencia de TI. ​​​​​​​​​​​​​​

Videos