이 제품의 최신 버전이 있습니다
다른 핀 출력을 지원하지만 비교 대상 장치와 동일한 기능.
BQ27530-G1
- Battery Fuel Gauge and Charger Controller for 1-
Cell Li-Ion Applications - Resides on System Main Board
- Battery Fuel Gauge Based on Patented
Impedance Track™ Technology- Models the Battery Discharge Curve for
Accurate Time-to-Empty Predictions - Automatically Adjusts for Battery Aging,
Battery Self-Discharge, and Temperature/Rate
Inefficiencies - Low-Value Sense Resistor (5 mΩ to 20 mΩ)
- Models the Battery Discharge Curve for
- Battery Charger Controller with Customizable
Charge Profiles- Configurable Charge Voltage and Current
based on Temperature - Optional State-Of-Health (SOH) and Multi-
Level Based Charge Profiles
- Configurable Charge Voltage and Current
- Host Free Autonomous Battery Management
System- Reduced Software Overhead Allows for Easy
Portability Across Platforms and Shorter OEM
Design Cycles - Higher Safety and Security
- Reduced Software Overhead Allows for Easy
- Run Time Improvements
- Longer Battery Runtime Leveraging
Impedance Track Technology - Tighter Accuracy Controls for Charger
Termination - Improved Recharged Thresholds
- Longer Battery Runtime Leveraging
- Intelligent Charging—Customized and Adaptive
Charging Profiles- Charger Control Based on SOH
- Temperature Level Charging (TLC)
- Battery Charger Controller for bq2416x Single Cell
Switchmode Battery Charger- Stand-Alone Charging Solution
- 400-kHz I2C™ Interface for Connection to System
Microcontroller Port - In a 15-Pin NanoFree™ Packaging
The Texas Instruments bq27530-G1 system-side Li-Ion Battery Management Unit is a microcontroller peripheral that provides Impedance Track™ fuel gauging and charging control for single-cell Li-Ion battery packs. The device requires little system microcontroller firmware development. Together with bq2416x Single-Cell Switchmode Charger, the bq27530-G1 manages an embedded battery (non-removable) or a removable battery pack.
The bq27530-G1 uses the patented Impedance Track™ algorithm for fuel gauging, and provides information such as remaining battery capacity (mAh), state-of-charge (%), runtime-to-empty (min), battery voltage (mV), temperature (°C), and state-of-health (%).
기술 자료
| 상위 문서 | 유형 | 직함 | 형식 옵션 | 최신 영어 버전 다운로드 | 날짜 |
|---|---|---|---|---|---|
| * | 데이터 시트 | bq27530-G1 Battery Management Unit Impedance Track™ Fuel Gauge with MaxLife Technology for Use with the bq2416x Charger Controller datasheet (Rev. C) | PDF | HTML | 2016. 3. 17 | |
| EVM User's guide | bq27530EVM with bq27530 Battery Management Unit Impedance Track Fuel Gauge (Rev. B) | 2016. 7. 31 | |||
| 애플리케이션 노트 | Host System Calibration Method (Rev. B) | 2016. 5. 19 | |||
| 애플리케이션 노트 | Going to Production With the bq275xx (Rev. F) | 2014. 10. 9 | |||
| 애플리케이션 노트 | Theory and Implementation of Impedance Track Battery Fuel-Gauging Algorithm (Rev. A) | PDF | HTML | 2014. 5. 16 | ||
| 애플리케이션 노트 | Using I2C Communication With the bq275xx Series of Fuel Gauges (Rev. B) | 2014. 5. 15 | |||
| 애플리케이션 노트 | How to Do Calibration and Create Golden DFI for Host Side Gas Gauge | 2011. 9. 1 | |||
| 애플리케이션 노트 | WinCE/Linux Drivers for bq275xx Fuel Gauge | 2011. 3. 17 | |||
| 애플리케이션 노트 | Updating bq275xx Firmware at Production (Rev. A) | 2011. 2. 21 | |||
| 애플리케이션 노트 | How to Generate Golden Image for Single-Cell Impedance Track(TM) Devices | 2010. 1. 7 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
BQ27530EVM — BQ27530EVM 시스템 측 Impedance-Track 연료(가스) 게이지 직접 배터리 연결 평가 모듈
BQSTUDIO-STABLE — Battery Management Studio (bqStudio) Software – stable version downloads for bq series of TI battery fuel gauges
bqStudio(Battery Management Studio)는 TI 배터리 관리 제품의 평가, 설계, 구성, 테스트 또는 기타 활용 프로세스를 지원하는 견고한 종합 툴을 제공합니다. 여기에는 실시간 감시, 그래프 및 로깅 지원, 명령 전송을 위한 간편한 인터페이스, 직접 저수준 통신 및 I/O, 구성, 보정, 학습 주기 수행, 장치를 생산 단계로 가져가기 위한 유용한 파일 생성 등 레지스터 및 데이터 메모리에 대한 전체 액세스를 제공하는 기능은 물론, 자동화된 가이드 지원도 포함됩니다.
bq20xxx 및 bq30xxx와 같은 (...)
BQSTUDIO-TEST — Battery Management Studio (bqStudio) Software – untested version downloads
bqStudio(Battery Management Studio)는 TI 배터리 관리 제품의 평가, 설계, 구성, 테스트 또는 기타 활용 프로세스를 지원하는 견고한 종합 툴을 제공합니다. 여기에는 실시간 감시, 그래프 및 로깅 지원, 명령 전송을 위한 간편한 인터페이스, 직접 저수준 통신 및 I/O, 구성, 보정, 학습 주기 수행, 장치를 생산 단계로 가져가기 위한 유용한 파일 생성 등 레지스터 및 데이터 메모리에 대한 전체 액세스를 제공하는 기능은 물론, 자동화된 가이드 지원도 포함됩니다.
bq20xxx 및 bq30xxx와 같은 (...)
BQ27XXXSW-LINUX — BQ27XXX용 Linux 드라이버
The Linux driver supports the BQ27x series of Battery Fuel Gauges. The Linux driver supports communication through the I2C/HDQ bus and interfaces with the power supply sub-system to monitor battery properties.
Linux Mainline Status
Available in Linux Main line: Yes
Available through git.ti.com: N/A
(...)
SLUC415 — bq27530-G1 Firmware
SLUC606 — Host System Calibration Method Software
BQ-BMS-PROGRAMMER-SW — Command line programmers for BQ products
BQ-BATTERY-PROGRAMMER-SW 소프트웨어 개발 키트(SDK)는 TI 배터리 관리 제품을 사용하는 팩의 프로그래밍, 테스트 또는 조립 프로세스를 지원하는 강력한 소프트웨어 명령줄 툴 모음입니다. 이 소프트웨어의 실행 파일은 EV2300 통신 트랜스시버용 MKST-3P-ALT-EV2300 MKS 기술 대안과 함께 작동합니다. 실행 파일은 단일 스테이션에서 작동하지만 MKS Technology Inc.의 추가 소프트웨어 및 GUI를 사용하여 여러 스테이션으로 확장할 수 있습니다. 이 소프트웨어에는 여러 스테이션에 대한 (...)
BQEVSW-MKST-UPDATE — Software Update to enable BQEVSW to use MKST-3P-ALT-EV2300
BQ-BATTERY-PROGRAMMER-SW 소프트웨어 개발 키트(SDK)는 TI 배터리 관리 제품을 사용하는 팩의 프로그래밍, 테스트 또는 조립 프로세스를 지원하는 강력한 소프트웨어 명령줄 툴 모음입니다. 이 소프트웨어의 실행 파일은 EV2300 통신 트랜스시버용 MKST-3P-ALT-EV2300 MKS 기술 대안과 함께 작동합니다. 실행 파일은 단일 스테이션에서 작동하지만 MKS Technology Inc.의 추가 소프트웨어 및 GUI를 사용하여 여러 스테이션으로 확장할 수 있습니다. 이 소프트웨어에는 여러 스테이션에 대한 (...)
BQMTESTER-MKST-UPDATE — Software Update to enable BQMTESTER to use MKST-3P-ALT-EV2300
BQ-BATTERY-PROGRAMMER-SW 소프트웨어 개발 키트(SDK)는 TI 배터리 관리 제품을 사용하는 팩의 프로그래밍, 테스트 또는 조립 프로세스를 지원하는 강력한 소프트웨어 명령줄 툴 모음입니다. 이 소프트웨어의 실행 파일은 EV2300 통신 트랜스시버용 MKST-3P-ALT-EV2300 MKS 기술 대안과 함께 작동합니다. 실행 파일은 단일 스테이션에서 작동하지만 MKS Technology Inc.의 추가 소프트웨어 및 GUI를 사용하여 여러 스테이션으로 확장할 수 있습니다. 이 소프트웨어에는 여러 스테이션에 대한 (...)
SLUC367 — bqEVSW installer for all bq275xx devices
SLUC416 — bqEVSW installer for bq27530-G1 device
TIDA-00029 — 시스템 측 ImpedanceTrack 연료(가스) 게이지 직접 배터리 연결 레퍼런스 디자인
This reference design, using bq27530, has a bq27530-G1 fuel gauge that directly communicates with bq24160/1 single-cell, Li-Ion battery charger via the I2C protocol. This complete battery charging solution does not require a microcontroller or processor to facilitate communication between the (...)
TIDA-00047 — 전원 경로를 지원하는 2.5A 듀얼 입력 단일 셀 스위치 모드 리튬 이온 배터리 충전기 레퍼런스 디자인
This reference design is a complete charger solution for evaluating compact, flexible, high-efficiency, USB-friendly, switch-mode charge management solution for single-cell, Li-ion and Li-polymer batteries used in a wide range of portable applications. The solution integrates a synchronous PWM (...)
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| DSBGA (YZF) | 15 | Ultra Librarian |
주문 및 품질
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.