CC3200
- CC3200 SimpleLink Wi-Fi—Consists of
Applications Microcontroller, Wi-Fi Network
Processor, and Power-Management Subsystems - Wi-Fi CERTIFIED™ Chip
- Applications Microcontroller Subsystem
- ARM® Cortex®-M4 Core at 80 MHz
- Embedded Memory
- RAM (Up to 256KB)
- External Serial Flash Bootloader, and
Peripheral Drivers in ROM
- 32-Channel Direct Memory Access (µDMA)
- Hardware Crypto Engine for Advanced Fast
Security, Including- AES, DES, and 3DES
- SHA2 and MD5
- CRC and Checksum
- 8-Bit Parallel Camera Interface
- 1 Multichannel Audio Serial Port (McASP)
Interface with Support for Two I2S Channels - 1 SD/MMC Interface
- 2 Universal Asynchronous Receivers and
Transmitters (UARTs) - 1 Serial Peripheral Interface (SPI)
- 1 Inter-Integrated Circuit (I2C)
- 4 General-Purpose Timers with 16-Bit Pulse-
Width Modulation (PWM) Mode - 1 Watchdog Timer
- 4-Channel 12-Bit Analog-to-Digital Converters
(ADCs) - Up to 27 Individually Programmable, Multiplexed
GPIO Pins
- Dedicated External SPI Interface for Serial Flash
- Wi-Fi Network Processor Subsystem
- Featuring Wi-Fi Internet-On-a-Chip™
- Dedicated ARM MCU
Completely Offloads Wi-Fi and Internet
Protocols from the Application Microcontroller - Wi-Fi and Internet Protocols in ROM
- 802.11 b/g/n Radio, Baseband, Medium Access
Control (MAC), Wi-Fi Driver, and Supplicant - TCP/IP Stack
- Industry-Standard BSD Socket Application
Programming Interfaces (APIs) - 8 Simultaneous TCP or UDP Sockets
- 2 Simultaneous TLS and SSL Sockets
- Industry-Standard BSD Socket Application
- Powerful Crypto Engine for Fast, Secure Wi-Fi
and Internet Connections with 256-Bit AES
Encryption for TLS and SSL Connections - Station, AP, and Wi-Fi Direct™ Modes
- WPA2 Personal and Enterprise Security
- SimpleLink Connection Manager for
Autonomous and Fast Wi-Fi Connections - SmartConfig™ Technology, AP Mode, and
WPS2 for Easy and Flexible Wi-Fi Provisioning - TX Power
- 18.0 dBm @ 1 DSSS
- 14.5 dBm @ 54 OFDM
- RX Sensitivity
- –95.7 dBm @ 1 DSSS
- –74.0 dBm @ 54 OFDM
- Application Throughput
- UDP: 16 Mbps
- TCP: 13 Mbps
- Power-Management Subsystem
- Integrated DC-DC Supports a Wide Range of
Supply Voltage:- VBAT Wide-Voltage Mode: 2.1 to 3.6 V
- VIO is Always Tied with VBAT
- Preregulated 1.85-V Mode
- Advanced Low-Power Modes
- Hibernate: 4 µA
- Low-Power Deep Sleep (LPDS): 250 µA
- RX Traffic (MCU Active): 59 mA @ 54 OFDM
- TX Traffic (MCU Active): 229 mA @ 54 OFDM,
Maximum Power - Idle Connected (MCU in LPDS):
825 µA @ DTIM = 1
- Integrated DC-DC Supports a Wide Range of
- Clock Source
- 40.0-MHz Crystal with Internal Oscillator
- 32.768-kHz Crystal or External RTC Clock
- Package and Operating Temperature
- 0.5-mm Pitch, 64-Pin, 9-mm × 9-mm QFN
- Ambient Temperature Range: –40°C to 85°C
Start your design with the industry’s first Wi-Fi CERTIFIED single-chip microcontroller unit (MCU) with built-in Wi-Fi connectivity. Created for the Internet of Things (IoT), the SimpleLink CC3200 device is a wireless MCU that integrates a high-performance ARM Cortex-M4 MCU, allowing customers to develop an entire application with a single IC. With on-chip Wi-Fi, Internet, and robust security protocols, no prior Wi-Fi experience is required for faster development. The CC3200 device is a complete platform solution including software, sample applications, tools, user and programming guides, reference designs, and the TI E2E™ support community. The device is available in a QFN package that is easy to layout.
The applications MCU subsystem contains an industry-standard ARM Cortex-M4 core running at 80 MHz. The device includes a wide variety of peripherals, including a fast parallel camera interface, I2S, SD/MMC, UART, SPI, I2C, and four-channel ADC. The CC3200 family includes flexible embedded RAM for code and data and ROM with external serial flash bootloader and peripheral drivers.
The Wi-Fi network processor subsystem features a Wi-Fi Internet-on-a-Chip and contains an additional dedicated ARM MCU that completely offloads the applications MCU. This subsystem includes an 802.11 b/g/n radio, baseband, and MAC with a powerful crypto engine for fast, secure Internet connections with 256-bit encryption. The CC3200 device supports Station, Access Point, and Wi-Fi Direct modes. The device also supports WPA2 personal and enterprise security and WPS 2.0. The Wi-Fi Internet-on-a-chip includes embedded TCP/IP and TLS/SSL stacks, HTTP server, and multiple Internet protocols.
The power-management subsystem includes integrated DC-DC converters supporting a wide range of supply voltages. This subsystem enables low-power consumption modes, such as the hibernate with RTC mode requiring less than 4 µA of current.
관심 가지실만한 유사 제품
비교 대상 장치와 동일한 기능을 지원하는 핀 대 핀.
비교 대상 장치와 유사한 기능.
기술 자료
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
CC3200-LAUNCHXL — SimpleLink Wi-Fi CC3200 론치패드
SimpleLink™ Wi-Fi® CC3200 LaunchPad™ 개발 키트(QFN 패키지 장치 포함)는 연결이 내장된 업계 최초의 단일 칩 프로그래밍 가능 MCU인 CC3200 무선 MCU(마이크로컨트롤러)를 위한 평가 개발 플랫폼입니다. 이 보드는 FTDI를 사용하는 온보드 에뮬레이션을 제공하며 센서가 포함되어 있어 바로 사용 가능한 완전한 환경을 제공합니다. 이 보드를 PC에 직접 연결하여 Code Composer Studio™ Cloud IDE(통합 개발 환경) 및 IAR Embedded Workbench 같은 (...)
CC3200AUDBOOST — SimpleLink Wi-Fi CC3100 오디오 부스터팩
The SimpleLink™ Wi-Fi® CC3200 Audio BoosterPack enables the evaluation and development with the digital audio peripheral [I2S] present on the SimpleLink™ Wi-Fi® CC3200 device. It contains a Class-D power amplifier to drive speakers and an ultra-low power audio codec, TLV320AIC3254, supporting (...)
CC3200STK-WIFIMK — SimpleLink™ Wi-Fi® CC3200 SensorTag
SimpleLink™ Wi-Fi® CC3200 SensorTag 개발 키트는 센서를 클라우드에 직접 연결하는 가장 빠르고 쉬운 방법 중 하나입니다!
새로운 Wi-Fi SensorTag 키트는 업계 최초의 Wi-Fi CERTIFIED™ 단일 칩 MCU(마이크로컨트롤러 유닛)인 저전력 SimpleLink Wi-Fi CC3200 무선 MCU를 기반으로 합니다. 따라서 SensorTag 키트를 AAA 배터리로 구동할 수 있습니다.
Wi-Fi SensorTag 키트에는 9개의 저전력 MEMS 센서가 포함되어 있습니다.
Wi-Fi를 사용하여 (...)
TMDSEMU200-U — XDS200 USB 디버그 프로브
XDS200은 TI 임베디드 장치를 디버깅하는 데 사용되는 디버그 프로브(에뮬레이터)입니다. 대부분의 장치의 경우 더욱 저렴한 신형 XDS110(www.ti.com/tool/TMDSEMU110-U)을 사용하실 것을 권장합니다. XDS200은 단일 포드에서 다양한 표준(IEEE1149.1, IEEE1149.7, SWD)을 지원합니다. 모든 XDS 디버그 프로브는 ETB(임베디드 트레이스 버퍼)가 포함되어 있는 모든 Arm® 및 DSP 프로세서에서 코어 및 시스템 트레이스를 지원합니다.
XDS200은 TI 20핀 커넥터(TI 14핀, (...)
TMDSEMU560V2STM-U — XDS560™ 소프트웨어 v2 시스템 추적 USB 디버그 프로브
XDS560v2는 디버그 프로브의 XDS560™ 제품군 중 최고의 성능을 가진 제품으로, 기존의 JTAG 표준(IEEE1149.1)과 cJTAG(IEEE1149.7)를 모두 지원합니다. SWD(직렬 와이어 디버그)는 지원하지 않습니다.
모든 XDS 디버그 프로브는 ETB(임베디드 추적 버퍼)가 있는 모든 ARM 및 DSP 프로세서에서 코어와 시스템 트레이스를 지원합니다. 핀을 통한 추적의 경우 XDS560v2 PRO TRACE가 필요합니다.
XDS560v2는 MIPI HSPT 60핀 커넥터(TI 14핀, TI 20핀 및 ARM (...)
TMDSEMU560V2STM-UE — XDS560v2 시스템 추적 USB 및 이더넷 디버그 프로브
The XDS560v2 is the highest performance of the XDS family of debug probes and supports both the traditional JTAG standard (IEEE1149.1) and cJTAG (IEEE1149.7). Note that it does not support serial wire debug (SWD).
All XDS debug probes support Core and System Trace in all ARM and DSP processors that (...)
LB-3P-TRACE32-WIRELESS — 무선 연결용 Lauterbach TRACE32® 디버그 시스템
Lauterbach의 TRACE32® 툴은 개발자가 다양한 종류의 TI 무선 연결 칩을 분석, 최적화 및 인증할 수 있도록 하는 첨단 하드웨어 및 소프트웨어 구성 요소 제품군입니다. 세계적으로 유명한 임베디드 시스템용 디버그 솔루션은 초기 사전 실리콘 개발부터 현장의 제품 인증 및 문제 해결에 이르기까지 다음을 포함하는 모든 개발 단계를 위한 완벽한 솔루션입니다. 전체 온칩 중단점 지원, 런타임 메모리 액세스, 플래시 프로그래밍 및 벤치마크 카운터. 모든 것이 스크립팅이 가능하므로 개발자는 동일한 테스트 시퀀스를 계속해서 (...)
TSK-3P-BLUEBOX — TASKING BlueBox hardware debugger
TASKING’s Debug, Trace, and Test tools offer comprehensive solutions for efficient debugging, tracing, and testing of TI's embedded systems. The scalable TASKING BlueBox debuggers allow users to easily flash, debug, and test across TI's portfolio. Development on TI hardware is made even easier with (...)
CC3200SDK — CC3200 Software Development Kit (SDK), Service Pack, and Add-Ons
The SimpleLink™ Wi-Fi® CC3200 SDK contains drivers for the CC3200 programmable MCU, 40+ sample applications, and documentation needed to use the solution. It also contains the flash programmer, a command line tool for flashing software, configuring network and software parameters (SSID, (...)
CC3XXXRADIOTEST — SimpleLink™ Wi-Fi® 무선 테스팅 툴
SimpleLink™ Wi-Fi® 무선 테스트 툴은 개발 및 인증 중 SimpleLink Wi-Fi CC31xx 및 CC32xx 설계를 RF 평가 및 테스트할 수 있는 Windows 기반 소프트웨어 툴입니다. 이 도구는 라디오를 전송 또는 수신 모드로 수동 설정해 낮은 수준의 라디오를 테스트하는 기능을 지원합니다. 이 툴을 사용하려면 무선 회로 이론 및 무선 테스트 방법에 대한 지식이 필요합니다.
IoT(사물 인터넷)용으로 제작된 SimpleLink Wi-Fi CC31xx 및 CC32xx 장치에는 온칩 Wi-Fi, 인터넷 및 (...)
CCSTUDIO — Code Composer Studio integrated development environment (IDE)
CCStudio™ IDE is part of TI's extensive CCStudio™ development ecosystem and is an integrated development environment for TI's microcontrollers, processors, wireless connectivity devices, and radar sensors. CCStudio IDE is available as desktop or cloud-based applications. The cloud version (...)
ENERGIA — Energia
Energia is an open source & community-driven integrated development environment (IDE) & software framework. Based on the Wiring framework, Energia provides an intuitive coding environment as well as a robust framework of easy-to-use functional APIs & libraries for programming a (...)
SYSCONFIG — Standalone desktop version of SysConfig
CCStudio™ SysConfig is part of TI's extensive CCStudio™ development ecosystem and is a configuration tool that simplifies hardware and software configuration challenges to accelerate software development.
SysConfig provides an intuitive graphical user interface for configuring pins, peripherals, (...)
TSK-3P-VX-TOOLSET — Arm용 TASKING VX-toolset
Arm용 VX-Toolset은 일부 Cortex-M 및 Cortex-R 코어 장치의 안전 필수 임베디드 소프트웨어 개발을 위해 인증된 컴파일러 툴체인입니다. Eclipse IDE 통합, 고급 멀티코어 지원, TASKING BlueBox 디버거와의 호환성을 제공하는 VX-toolset은 개발을 단순화합니다. 최대 ASIL D까지의 ISO 26262 및 ISO 21434 규격 준수를 위해 TÜV NORD 인증을 획득했습니다.
SIMPLELINK-ACADEMY-CC32XX — SimpleLink™ Academy for CC32xx
WIFISTARTERPRO — SimpleLink™ Wi-Fi® 스타터 프로
iTunes App Store에서 다운로드
Google Play에서 다운로드
SimpleLink™ Wi-Fi® 스타터 프로 모바일 앱은 SimpleLink 프로비저닝을 위한 새로운 모바일 애플리케이션입니다. 장치 측에서 실행되는 임베디드 프로비저닝 라이브러리 및 예제와 함께 제공됩니다. 새로운 프로비저닝 릴리스는 SimpleLink Wi-Fi 제품을 사용한 Wi-Fi 프로비저닝을 위한 TI의 권장 사항입니다. 성공적인 프로세스를 보장하기 위해 피드백 및 폴백 옵션과 함께 고급 AP 모드 프로비저닝을 구현합니다. 고객은 임베디드 (...)
EMBEDDED-PROGRAMMING — SimpleLink™ Wi-Fi® 임베디드 프로그래밍
임베디드 CC3120/CC3220 장치가 탑재된 각 제품에는 직렬 플래시 장치도 연결되어 있어야 합니다. 직렬 플래시는 포맷되어야 하며, 최소한 필요한 소프트웨어 업데이트와 추가 기능이 포함된 서비스 팩으로 프로그래밍되어야 합니다. CC3220의 경우 내부 MCU 프로세서에서 실행되는 이진 이미지도 프로그래밍되어해야 합니다. 직렬 플래시 프로그래밍에는 다음과 같은 몇 가지 기존 옵션이 있습니다:
- Uniflash – 이미지 생성 및 프로그래밍을 제공하는 PC 기반 유틸리티입니다. 콘텐츠는 UART를 통해 프로그래밍됩니다.
- 무선 (...)
UNIFLASH — UniFlash for most TI microcontrollers (MCUs) and mmWave sensors
UniFlash는 TI의 광범위한 CCStudio™ 개발 에코시스템의 일부로, TI 마이크로컨트롤러 및 무선 연결 장치의 온칩 플래시와 TI 프로세서의 온보드 플래시를 프로그래밍하기 위한 소프트웨어 도구입니다. UniFlash는 그래픽 및 명령줄 인터페이스를 모두 제공하며, 데스크톱 또는 클라우드 환경에서 실행할 수 있습니다.
UniFlash는 CCStudio™ 개발자 영역의 클라우드에서 실행하거나 Windows®, Linux®, macOS® 컴퓨터에서 다운로드해 사용할 수 있습니다.
macOS는 mmWave, AMx, K2G 및 (...)
TIDCAL4 — CC3200 Wi-Fi Enabled NFC Card Reader Software
TIDCAL5 — CC3200 Smart Plug Gen1 Software
TIDCCW7 — CC3200 Video Camera Software
SIMPLELINK-CC3XXX-CERTIFICATION — SimpleLink™ CC3XXX에 대한 무선 인증
CC3XXX 인증 지원을 찾고 계십니까? SIMPLELINK-CC3XXX-CERTIFCATION은 CC31XX, CC32XX 및 CC33XX 제품의 성공적인 인증을 위한 관련 정보와 지원을 제공합니다. 이 페이지에서는 칩 다운 솔루션을 사용한 설계를 위한 TI의 모듈에 대한 최신 인증 보고서와 평가 보드를 확인할 수 있습니다.
3P-WIRELESS-MODULES — 타사 무선 모듈 검색 툴
타사 무선 모듈 검색 툴은 개발자가 완제품 사양을 충족하는 제품을 식별하고 생산 준비가 완료된 무선 모듈을 조달하는 데 유용합니다. 검색 툴에 포함되어 있는 타사 모듈 공급업체는 TI 무선 연결 제품을 사용하여 무선 모듈을 설계 및 제조하는 전문성을 갖춘 독립 회사입니다.
SWRR177 — CC3x00 Design Checklist
많은 TI 레퍼런스 설계에는 CC3200이(가) 포함됩니다.
레퍼런스 디자인 선택 툴을 사용하여 애플리케이션 및 매개 변수에 가장 적합한 설계를 검토하고 식별할 수 있습니다.
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| VQFN (RGC) | 64 | Ultra Librarian |
주문 및 품질
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.