LM8335
- MIPI RFFE Interface Version 1.10 Compliant
- Supports Output Expansion
- Host Interface Address Select Pin:
- ADR=GND, USID[3:0]=0001
- ADR=VDD, USID[3:0]=1001
- Pin-Configurable Initial State: VIO
- CFG=GND, GPO High-z, with Weak Internal Pull-Down Resistor Enabled; GPO_OUT_DATA is Unmasked
- CFG=VDD, GPO High-z, with Weak Internal Pull-Down Resistor Enabled; GPO_OUT_DATA is Masked
- Three Sources for Chip Reset:
- VIO Input Pin
- POR
- Software-Commanded Reset
Key Specifications
- 1.8 ± 0.15V MIPI RFFE Operation (VIO)
- 1.8 ± 0.15V Core Supply (VDD)
- 1.65 to 3.6V GPO Supply (VDDIO)
- Low Standby and Active Current
- On-Chip Power-On Reset (POR)
- −30 to +85°C Ambient Temperature Range
- 16-Bump DSBGA Package
- 1.965 mm x 1.965 mm x 0.6 mm, 0.5 mm Pitch (Nominal)
All trademarks are the property of their respective owners.
The LM8335 General Purpose Output Expander is a dedicated device to provide flexible and general purpose, host programmable output expansion functions. This device communicates with a host processor through a MIPI® RFFE Interface (Mobile Industry Processor Interface RF Front-End).
Eight general purpose outputs (GPO) can be configured by the host controller as drive high/low/high-z. Weak pull-ups (PU) or weak pull-downs (PD) can be enabled.
Upon power-on, the LM8335 default configuration is for all GPO to be set based on the state of the CFG pin.
After startup, any changes to the default configuration must be sent from the host via the MIPI RFFE host interface..
The LM8335 is available in a 16-bump lead-free DSBGA package of size 1.965 mm x 1.965 mm x 0.6 mm (0.5 mm pitch).
기술 문서
유형 | 직함 | 날짜 | ||
---|---|---|---|---|
* | Data sheet | LM8335 General-Purpose Output Expander with MIPI RFFE Host Interface datasheet (Rev. B) | 2013/05/02 | |
Application note | Choosing the Correct I2C Device for New Designs | PDF | HTML | 2016/09/07 | |
Application note | Understanding the I2C Bus | PDF | HTML | 2015/06/30 | |
Application note | Maximum Clock Frequency of I2C Bus Using Repeaters | 2015/05/15 | ||
Application note | I2C Bus Pull-Up Resistor Calculation | PDF | HTML | 2015/02/13 | |
User guide | LM8335 Evaluation Module (Rev. A) | 2013/05/03 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
LM8335EVM — LM8335 MIPI RFFE 호스트 인터페이스를 갖춘 범용 출력 확장장치 평가 모듈 보드
General-Purpose Output Expander with MIPI RFFE Host Interface Evaluation Module - I2C IO Expander
The EVM operates from USB supplied power. This board supports USB to MIPI RFFE communication to support evaluation of the LM8335 MIPI RFFE to General Purpose Output (GPO) expansion.PSPICE-FOR-TI — TI 설계 및 시뮬레이션 툴용 PSpice®
TI 설계 및 시뮬레이션 환경용 PSpice는 기본 제공 라이브러리를 이용해 복잡한 혼합 신호 설계를 시뮬레이션할 수 있습니다. 레이아웃 및 제작에 (...)
TINA-TI — SPICE 기반 아날로그 시뮬레이션 프로그램
패키지 | 핀 | 다운로드 |
---|---|---|
DSBGA (YZR) | 16 | 옵션 보기 |
주문 및 품질
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
- 팹 위치
- 조립 위치
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.