OPA2690
- FLEXIBLE SUPPLY RANGE:
+5V to +12V Single Supply
±2.5V to ±6V Dual Supply - WIDEBAND +5V OPERATION: 220MHz (G = 2)
- HIGH OUTPUT CURRENT: 190mA
- OUTPUT VOLTAGE SWING: ±4.0V
- HIGH SLEW RATE: 1800V/µs
- LOW SUPPLY CURRENT: 5.5mA/ch
- LOW DISABLE CURRENT: 100µA/ch
- APPLICATIONS
- VIDEO LINE DRIVING
- xDSL LINE DRIVER/RECEIVER
- HIGH-SPEED IMAGING CHANNELS
- ADC BUFFERS
- PORTABLE INSTRUMENTS
- TRANSIMPEDANCE AMPLIFIERS
- ACTIVE FILTERS
The OPA2690 represents a major step forward in unity-gain stable, voltage-feedback op amps. A new internal architecture provides slew rate and full-power bandwidth previously found only in wideband, current-feedback op amps. A new output stage architecture delivers high currents with a minimal headroom requirement. These give exceptional single-supply operation. Using a single +5V supply, the OPA2690 can deliver a 1V to 4V output swing with over 120mA drive current and 150MHz bandwidth. This combination of features makes the OPA2690 an ideal RGB line driver or single-supply Analog-to-Digital Converter (ADC) input driver.
The low 5.5mA/ch supply current of the OPA2690 is precisely trimmed at +25°C. This trim, along with low temperature drift, provides lower maximum supply current than competing products. System power may be reduced further using the optional disable control pin. Leaving this disable pin open, or holding it HIGH, will operate the OPA2690I-14D normally. If pulled LOW, the OPA2690I-14D supply current drops to less than 200µA/ch while the output goes to a high-impedance state.
기술 자료
| 상위 문서 | 유형 | 직함 | 형식 옵션 | 최신 영어 버전 다운로드 | 날짜 |
|---|---|---|---|---|---|
| * | 데이터 시트 | Dual, Wideband, Voltage-Feedback Operational Amplifier with Disable datasheet (Rev. G) | 2010. 3. 4 | ||
| e북 | The Signal e-book: A compendium of blog posts on op amp design topics | PDF | HTML | 2017. 3. 28 | ||
| 애플리케이션 노트 | Design for a Wideband Differential Transimpedance DAC Output (Rev. A) | 2016. 10. 17 | |||
| 애플리케이션 노트 | RLC Filter Design for ADC Interface Applications (Rev. A) | 2015. 5. 13 | |||
| 사용 설명서 | DEM-OPA-SO-2A User's Guide (Rev. B) | 2010. 4. 30 | |||
| 애플리케이션 노트 | Wireline Data Transmission and Reception | 2010. 1. 27 | |||
| 사용 설명서 | DEM-OPA-SO-2D User's Guide (Rev. A) | 2006. 5. 25 | |||
| 애플리케이션 노트 | Noise Analysis for High Speed Op Amps (Rev. A) | 2005. 1. 17 | |||
| 애플리케이션 노트 | ADS5500, OPA695: PC Board Layout for Low Distortion High-Speed ADC Drivers | 2004. 4. 22 | |||
| 애플리케이션 노트 | Measuring Board Parasitics in High-Speed Analog Design | 2003. 7. 7 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
DEM-OPA-SO-2A — SO-8 패키지용 듀얼 연산 증폭기 평가 모듈
The DEM-OPA-SO-2A demonstration evaluation module helps designers evaluate the operation and performance of TI dual-channel, high-speed, wideband operational amplifiers. This unpopulated printed-circuit board (PCB) is compatible with products offered in the 8-lead SOIC (D) package.
For more (...)
DEM-OPA-SO-2D — SO-14 패키지용 듀얼 연산 증폭기 평가 모듈
DEM-OPA-SO-2D 데모 보드는 비활성화 기능을 갖춘 SO-14(DDB) 패키지용 TI 이중 고속 연산 증폭기의 작동 및 성능을 평가하기 위한 범용 비실장 PCB(인쇄 회로 보드)입니다.
ANALOG-ENGINEER-CALC — PC software analog engineer's calculator
아날로그 엔지니어의 계산기는 아날로그 회로 설계 엔지니어가 정기적으로 사용하는 많은 반복 계산의 속도를 높이도록 설계되었습니다. 이 PC 기반 툴은 피드백 저항을 사용한 연산 증폭기 게인 설정부터 아날로그-디지털 컨버터(ADC) 드라이브 버퍼 회로 안정화를 위한 적절한 회로 설계 요소 선택에 이르기까지 다양한 일반적인 계산 목록이 포함된 그래픽 인터페이스를 제공합니다.
이 계산기는 독립 실행형 툴로 유용할 뿐만 아니라 아날로그 엔지니어의 포켓 레퍼런스에 설명된 개념과도 잘 어울립니다.
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| SOIC (D) | 14 | Ultra Librarian |
| SOIC (D) | 8 | Ultra Librarian |