PCA9535
- Low standby-current consumption of 1 µA Max
- I2C to Parallel port expander
- Open-drain active-low interrupt output
- 5-V Tolerant I/O ports
- Compatible with most microcontrollers
- 400-kHz Fast I2C Bus
- Address by three hardware address pins for use of up to eight devices
- Polarity inversion register
- Latched outputs with high-current drive capability for directly driving LEDs
- Latch-up performance exceeds 100 mA Per JESD 78, class II
- ESD Protection exceeds JESD 22
- 2000-V Human-body model (A114-A)
- 1000-V Charged-device model (C101)
INT can be connected to the interrupt input of a microcontroller. By sending an interrupt signal on this line, the remote I/O can inform the microcontroller if there is incoming data on its ports without having to communicate via the I2C bus. Thus, the PCA9535 can remain a simple slave device.
The device outputs (latched) have high-current drive capability for directly driving LEDs. The device has low current consumption.
Although pin-to-pin and I2C address compatible with the PCF8575, software changes are required due to the enhancements.
The PCA9535 is identical to the PCA9555, except for the removal of the internal I/O pullup resistor, which greatly reduces power consumption when the I/Os are held low.
Three hardware pins (A0, A1, and A2) are used to program and vary the fixed I2C address and allow up to eight devices to share the same I2C bus or SMBus. The fixed I2C address of the PCA9535 is the same as the PCA9555, PCF8575, PCF8575C, and PCF8574, allowing up to eight of these devices in any combination to share the same I2C bus or SMBus.
기술 문서
| 유형 | 직함 | 날짜 | ||
|---|---|---|---|---|
| * | Data sheet | PCA9535 Remote 16-BIT I2C and SMBus Low-Power I/O Expander With Interrupt Output and Configuration Registers datasheet (Rev. K) | PDF | HTML | 2021/03/11 |
| Application note | I2C Dynamic Addressing | 2019/04/25 | ||
| Selection guide | Logic Guide (Rev. AB) | 2017/06/12 | ||
| Application note | Choosing the Correct I2C Device for New Designs | PDF | HTML | 2016/09/07 | |
| Application note | Understanding and Interpreting Standard-Logic Data Sheets (Rev. C) | 2015/12/02 | ||
| Application note | Understanding the I2C Bus | PDF | HTML | 2015/06/30 | |
| Application note | Maximum Clock Frequency of I2C Bus Using Repeaters | 2015/05/15 | ||
| Application note | I2C Bus Pull-Up Resistor Calculation | PDF | HTML | 2015/02/13 | |
| Application note | Programming Fun Lights With TI's TCA6507 | 2007/11/30 | ||
| Application note | Semiconductor Packing Material Electrostatic Discharge (ESD) Protection | 2004/07/08 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
I2C-DESIGNER — I2C 디자이너 툴
PSPICE-FOR-TI — TI 설계 및 시뮬레이션 툴용 PSpice®
TI 설계 및 시뮬레이션 환경용 PSpice는 기본 제공 라이브러리를 이용해 복잡한 혼합 신호 설계를 시뮬레이션할 수 있습니다. 레이아웃 및 제작에 (...)
TINA-TI — SPICE 기반 아날로그 시뮬레이션 프로그램
| 패키지 | 핀 | 다운로드 |
|---|---|---|
| SOIC (DW) | 24 | 옵션 보기 |
| SSOP (DB) | 24 | 옵션 보기 |
| SSOP (DBQ) | 24 | 옵션 보기 |
| TSSOP (PW) | 24 | 옵션 보기 |
| TVSOP (DGV) | 24 | 옵션 보기 |
| VQFN (RGE) | 24 | 옵션 보기 |
| WQFN (RTW) | 24 | 옵션 보기 |
주문 및 품질
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
- 팹 위치
- 조립 위치
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.