인터페이스 I2C, I3C 및 SPI IC I2C 및 I3C 레벨 시프터, 버퍼 및 허브

TCA9416

활성

초저전압 I2C 트랜스레이터 - 상승 시간 가속기 포함

제품 상세 정보

Features Output Enable Protocols I2C Frequency (max) (MHz) 1 VCCA (min) (V) 1.08 VCCA (max) (V) 3.6 VCCB (min) (V) 1.08 VCCB (max) (V) 3.6 Supply restrictions No rule Rating Catalog Operating temperature range (°C) -40 to 125
Features Output Enable Protocols I2C Frequency (max) (MHz) 1 VCCA (min) (V) 1.08 VCCA (max) (V) 3.6 VCCB (min) (V) 1.08 VCCB (max) (V) 3.6 Supply restrictions No rule Rating Catalog Operating temperature range (°C) -40 to 125
X2SON (DTM) 8 1.08 mm² (0.8 mm × 1.35 mm) SOT-23-THN (DDF) 8 8.12 mm² (2.9 mm × 2.8 mm)
  • 2-bit bidirectional translator for SDA and SCL lines in I2C applications
  • Provides bidirectional voltage translation with no direction pin
  • High-impedance output SCL_A, SDA_A, SCL_B, SDA_B pins when OE = 0 V or VCC = 0 V
  • Internal 10-kΩ pull-up resistor on all SDA and SCL pins are enabled based on respective VCC voltage
  • 1.08 V to 3.6 V on both A and B ports
  • VCC Isolation feature: If either VCC input is at GND, both ports are in the high-impedance state (excluding pull-ups)
  • No power-supply sequencing required: either VCCA or VCCB can be ramped first
  • Low Ioff of 2.5 µA when either VCCA or VCCB = 0 V
  • OE input can be tied directly to VCCA or controlled by GPIO
  • Latch-up performance exceeds 100 mA per JESD 78, class II
  • ESD Protection exceeds JESD 22
    • 2500-V Human-body model (A114-B)
    • 1500-V Charged-device model (C101)
  • 2-bit bidirectional translator for SDA and SCL lines in I2C applications
  • Provides bidirectional voltage translation with no direction pin
  • High-impedance output SCL_A, SDA_A, SCL_B, SDA_B pins when OE = 0 V or VCC = 0 V
  • Internal 10-kΩ pull-up resistor on all SDA and SCL pins are enabled based on respective VCC voltage
  • 1.08 V to 3.6 V on both A and B ports
  • VCC Isolation feature: If either VCC input is at GND, both ports are in the high-impedance state (excluding pull-ups)
  • No power-supply sequencing required: either VCCA or VCCB can be ramped first
  • Low Ioff of 2.5 µA when either VCCA or VCCB = 0 V
  • OE input can be tied directly to VCCA or controlled by GPIO
  • Latch-up performance exceeds 100 mA per JESD 78, class II
  • ESD Protection exceeds JESD 22
    • 2500-V Human-body model (A114-B)
    • 1500-V Charged-device model (C101)

The TCA9416 is a 2-bit bidirectional I2C and SMBus voltage-level translator with an output enable (OE) input and rising and falling edge accelerators. It is operational from 1.08 V to 3.6 V on both the A-side and B-side. This allows the device to interface between lower and higher logic signal levels at any of the typical 1.2-V, 1.8-V, 2.5-V, and 3.3-V supply rails.

The OE input pin is referenced to VCCA, can be tied directly to VCCA, but it is also 3.6-V tolerant. The OE pin can also be controlled and set to a logic low to place all the SCL and SDA pins in a high-impedance state, which significantly reduces the quiescent current consumption.

Under normal I2C and SMBus configurations, the TCA9416 is compatible with standard speeds where the frequency of SCL is 100 kHz (Standard-mode), 400 kHz (Fast-mode), or 1 MHz (Fast-mode Plus).

The TCA9416 features internal 10-kΩ pull-up resistors on SCL_A, SDA_A, SCL_B, and SDA_B. Additional external pull-up resistors can be added to the bus to reduce the total pull-up resistance and speed up rising edges.

The TCA9416 is a 2-bit bidirectional I2C and SMBus voltage-level translator with an output enable (OE) input and rising and falling edge accelerators. It is operational from 1.08 V to 3.6 V on both the A-side and B-side. This allows the device to interface between lower and higher logic signal levels at any of the typical 1.2-V, 1.8-V, 2.5-V, and 3.3-V supply rails.

The OE input pin is referenced to VCCA, can be tied directly to VCCA, but it is also 3.6-V tolerant. The OE pin can also be controlled and set to a logic low to place all the SCL and SDA pins in a high-impedance state, which significantly reduces the quiescent current consumption.

Under normal I2C and SMBus configurations, the TCA9416 is compatible with standard speeds where the frequency of SCL is 100 kHz (Standard-mode), 400 kHz (Fast-mode), or 1 MHz (Fast-mode Plus).

The TCA9416 features internal 10-kΩ pull-up resistors on SCL_A, SDA_A, SCL_B, and SDA_B. Additional external pull-up resistors can be added to the bus to reduce the total pull-up resistance and speed up rising edges.

다운로드 스크립트와 함께 비디오 보기 비디오

기술 자료

검색된 결과가 없습니다. 검색어를 지우고 다시 시도하세요.
3개 모두 보기
상위 문서 유형 직함 형식 옵션 최신 영어 버전 다운로드 날짜
* 데이터 시트 TCA9416 Ultra-Low-Voltage I2C Translator with Rise Time Accelerators datasheet (Rev. A) PDF | HTML 2021. 8. 6
애플리케이션 노트 Understanding Transient Drive Strength vs. DC Drive Strength in Level-Shifters (Rev. A) PDF | HTML 2024. 7. 3
인증서 TCA9416EVM EU Declaration of Conformity (DoC) 2021. 2. 25

설계 및 개발

추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.

평가 보드

TCA9416EVM — 상승 시간 가속기가 포함된 TCA9416 초저전압 I2C 트랜스레이터 평가 모듈

이 EVM은 조정 가능한 풀업 저항기와 버스 정전 용량을 통해 구성 가능한 로딩 조건을 제공하여 설계자가 시스템에서 이 장치의 성능을 쉽게 테스트할 수 있게 도와줍니다.

사용 설명서: PDF | HTML
지원되는 제품 및 하드웨어
재고 있음
제한:
??asset.out-of-stock-ti_ko_KR??
이용할 수 없음
시뮬레이션 모델

TCA9416 IBIS Model

SCPM047.ZIP (63 KB) - IBIS 모델
지원되는 제품 및 하드웨어
설계 툴

I2C-DESIGNER — I2C 디자이너 툴

I2C 설계자 툴을 사용하여 I2C 기반 설계의 주소 지정, 전압 레벨 및 주파수의 충돌을 신속하게 해결합니다. 마스터 및 슬레이브 입력을 입력하여 I2C 트리를 자동으로 생성하거나 사용자 지정 솔루션을 쉽게 구축합니다. 이 툴을 사용하면 설계자가 누락 승인을 디버깅하고, 풀업 저항을 선택하고, I2C 버스의 최대 커패시턴스 부하를 충족하는 방법에 대한 지침을 통해 시간을 절약하고 I2C 표준을 준수할 수 있습니다. 
지원되는 제품 및 하드웨어
패키지 CAD 기호, 풋프린트 및 3D 모델
X2SON (DTM) 8 Ultra Librarian
SOT-23-THN (DDF) 8 Ultra Librarian

주문 및 품질

권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.

지원 및 교육

TI 엔지니어의 기술 지원을 받을 수 있는 TI E2E™ 포럼

콘텐츠는 TI 및 커뮤니티 기고자에 의해 "있는 그대로" 제공되며 TI의 사양으로 간주되지 않습니다. 사용 약관을 참조하십시오.

품질, 패키징, TI에서 주문하는 데 대한 질문이 있다면 TI 지원을 방문하세요. ​​​​​​​​​​​​​​

동영상