TPS929240-Q1
- AEC-Q100 qualified for automotive applications:
- Temperature grade 1: –40°C to +125°C, TA
- 24-channel precision high-side current output:
- Device supply voltage 4.5V to 40V
- LED supply voltage 4V to 36V
- Up to 100mA channel current set by resistor
- 2-bit global, 6-bit independent current setting
- High-current accuracy < ±5% at 5mA to 100mA
- Low voltage drop 750mV at 100mA
- 12-bit independent PWM dimming
- Programmable PWM frequency up to 20kHz
- Phase-shift PWM dimming
- Linear and exponential dimming method
-
FlexWire™ control interface
- Up to 1MHz clock frequency
- Maximum 16 devices on one FlexWire bus
- Up to 24 bytes data transaction in one frame
- 5V LDO output to supply CAN transceiver
- Diagnostic and protection:
- Programmable FAIL-SAFE state
- LED open-circuit detection
- LED short-circuit detection
- Single-LED short-circuit diagnostic
- Programmable low-supply detection
- Open-drain ERR for fault indication
- Watchdog and CRC for FlexWire interface
- 8-bit ADC for pin voltage measurement
- Overtemperature protection
With the increasing demand for animation in automotive lighting, LEDs must be controlled independently. Therefore, LED drivers with digital interfaces are essential to effectively drive pixel-controlled lighting applications. In exterior lighting, multiple lamp functions are typically located on different PCB boards with off-board wires connected to each other. It is difficult for a traditional single-ended interface to meet the strict EMC requirements. By using an industrial-standard CAN physical layer, the UART-based FlexWire interface of the TPS929240-Q1 easily accomplishes long distance off-board communication without impacting EMC.
The TPS929240-Q1 is a 24-channel, 40V high-side LED driver that controls the 8-bit output current and 12-bit PWM duty cycles. The device meets multiple regulation requirements with LED open-circuit, short-to-ground, and single LED short-circuit diagnostics. A configurable watchdog also automatically sets FAIL-SAFE states when the MCU connection is lost, and, with programmable EEPROM, TPS929240-Q1 can flexibly be set for different application scenarios.
기술 자료
| 상위 문서 | 유형 | 직함 | 형식 옵션 | 최신 영어 버전 다운로드 | 날짜 |
|---|---|---|---|---|---|
| * | 데이터 시트 | TPS929240-Q1 24-Channel, Automotive, 40V, High-Side (O)LED Driver With FlexWire™ Interface datasheet (Rev. B) | PDF | HTML | 2024. 4. 16 | |
| 사용 설명서 | TPS929xxx-Q1 Sample Code User's Guide | PDF | HTML | 2023. 4. 10 | ||
| 애플리케이션 노트 | Typical Application to Achieve High Immunity to BCI | PDF | HTML | 2022. 11. 7 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
TPS929240EVM — 24채널 오토모티브 LED 드라이버용 TPS929240-Q1 평가 모듈
설계자는 TPS929240-Q1 EVM(평가 모듈)을 이용해 오토모티브 조명 애플리케이션 용도로 출력 전류와 PWM 듀티 사이클을 개별 제어할 수 있는 FlexLED™ 인터페이스가 포함된 12채널 40V 고압측 LED 드라이버 TPS929240-Q1의 작동 및 성능을 평가할 수 있습니다. 또한, LED 개방 회로, 접지 단락 및 단일 LED 단락 회로 진단 기능도 갖고 있습니다. MCU 연결이 끊기거나 MCU 제어가 없는 경우 자동적으로 사전 정의된 안전 상태로 들어가는 기능을 지원합니다.
OPTEEQ-3P-SG400-SERIES — OPTEEQ SG400 시리즈 범용 인시스템 갱 프로그래머
OPTEEQ Technologies는 반도체 칩 프로그래밍에 대한 10년 이상의 깊이 있는 전문 지식을 갖춘 시장 선두 주자입니다. OPTEEQ SG400E 프로그래머는 1~32채널 옵션을 제공합니다. SG400 시리즈의 높은 안정성과 초고속 프로그래밍 속도를 유지하면서 새롭게 설계된 독립 전원 공급 시스템을 통해 고객의 다양한 응용 시나리오를 충족합니다. 또한 VCC/VPP 고속 방전 회로와 이중 과부하 보호 회로를 추가하여 자동차 전자 장치, 산업 제어 및 기타 산업에서 PCB의 대량 생산 및 테스트에 이상적이며 고객이 백만 (...)
TPS929240Q1-F5529-SW — TPS929240-Q1 reference code based on MSP430F5529 (MSP-EXP430F5529LP)
SLVRBM1 — TPS929240-Q1 TPS929160-Q1 EEPROM Configuration Tool
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| HTSSOP (DCP) | 38 | Ultra Librarian |
주문 및 품질
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.